Digitus DN-95341-1 Manual de usuario

8 Port Gigabit PoE Switch,

19 Inch, Unmanaged,

2 SFP Uplink

Quick Installation Guide

DN-95341-1

1. Introduction

The DIGITUS 8-Port Gigabit Rack mount Switch with eight Power over Ethernet ports

and two additional SFP Fiber Port, offers your network significant improvement in

terms of performance and efficiency. Thanks to PoE support, you only need a single

(network) cable for power and data transfer. This switch makes it much easier to

connect devices such as access points, network cameras, and IP telephones, and

requires far less cabling than alternatives. It also allows you to extend your network

in places where there are no power supply cables or sockets available. The switch

does not require any configuration and therefore guarantees quick and seamless

integration into the network. Moreover, the switch has a rack mountable design and

can be easily installed with many standard racks, which makes this device the perfect

solution for data center and local server rooms.

2. Features

8-Port 10/100/1000 Mbps PoE Gigabit rack mountable Switch + 2x SFP Uplink

Ethernet IEEE802.3 / 802.3u / 802.3x/802.3ab/802.3z / IEEE802.3 af/at

Power over Ethernet (PoE) - You only need one cable for power and data transfer

PoE power budget: 140 Watts

Supports PoE: Provides 8 PoE Port, each port output 30W maximum power

No configuration necessary

Status LEDs on each port

Pin Feet: V+ (RJ45 Pin 3, 6) V- (RJ45 Pin 1, 2)

Backplane: 20Gbps

MAC address table: 4K

Rack mountable in system rack (1U)

Internal power supply: 150W

Dimensions (L x W x H): 275 mm x 200 mm x 44 mm

Weight: 4500g

Ethernet speed: Gigabit

Number of ports (uplink): 2

Connection of uplink port: SFP

VLAN: no

PoE standard: IEEE802.3at (PoE+)

3. Package Contents

8P POE switch 2 SFP Uplink Ports

User Manual

Power Cable

Rubber feet 4pcs

Mounting brackets 2pcs

Screws 6pcs

4. Specifications

Fixed port

8 x 10/100/1000Mbps PoE ports and

2 Gigabit SFP Ports

Standards and protocols

IEEE802.3 10Base-T Ethernet standard

IEEE802.3u 100Base-TX Fast Ethernet standard

IEEE802.3ab 1000Base-T Ethernet standard

IEEE802.3z Gigabit Ethernet (fiber)

IEEE802.3x Full duplex flow control and

Backpressure Half duplex flow control

IEEE802.3ab Link aggregation

Forwarding Rate

10/100/1000Mbps

LED Indicators

Power, Link/Act, PoE

AC Input Voltage Range

100V～240V AC，50/60Hz

Operating temperature

0°C ~ 40°C

Storage temperature

-10°C ~ 70°C

Operating humidity

5%～95% (non-condensing)

Exchange capacity

20G

MAC Addresses

Power Supply

150W

Power Consumption

10W

PoE Technology

PoE Compliance

100% IEEE 802.3af, 802.3at compliant

PoE Classification

PSE (Power Sourcing Equipment)

PoE Voltage

+52 VDC

PoE Power Budget

140W

PoE Power

Up to 30 W per port

PoE Operation

Automatic detection and power management

PoE Pin Assignments

V+ (RJ45 Pin 3, 6), V- (RJ45 Pin 1, 2)

PoE Disconnect Mode

DC disconnect

Mechanical

Casing

Metal

Dimensions (W x L x H)

275mm x 200mm x 44 mm

Installation

Rack mounting or Desktop

5. External Component Description

Front Panel

The front panel consists of LED indications and network ports.

PWR LED: The Power LED lights up when the Switch is connected to a power source.

Link/Act LED: The Link/Act LED flashes which indicates a network link through the

corresponding port. Blinking indicates that the Switch is either sending or receiving

data to the port.

PoE indicator: constant brightness indicates that the PD device is connected to the

corresponding port, and extinguished indicates that the port is not powered or no PD

device is found.

Real Panel

The rear panel view of the Switch consists of an AC power connector.

Power outlet: Supports input voltages 100-240VAC, 50/60Hz.

Switch: Used to connect the power supply.

Fuse: Prevent affect the power grid from equipment short circuit.

(Tank containing a spare fuse)

Grounding: use specialized ground lead connect.

6. Hardware installation

6.1 switch installation

For safe switch installation and operation,

it is recommended that you:

Visually inspect the power cord to see that it is secured fully to the AC power

connector

Make sure that there is proper heat dissipation and adequate ventilation around

the switch.

Do not place heavy objects on the switch.

Desktop or Shelf Installation

When installing the switch on a desktop or shelf, the rubber feet included with the

device must be attached on the bottom at each corner of the device's base. Allow

enough ventilation space between the device and the objects around it.

Rack Installation

The switch can be mounted in an EIA standard size 19-inch rack, which can be placed

in a wiring closet with other equipment. To install, attach the mounting brackets to

the switch's side panels (one on each side) and secure them with the screws

provided (please note that these brackets are not designed for palm size switches).

Then, use the screws provided with the equipment rack to mount the switch in the

rack.

6.2 Plugging in the AC Power Cord

You can connect AC power supply cord to switch back and the other side connect the

power outlet. (Power outlet might as well grounding and support over voltage

protection)

Warning: Do not turn on the power switch before power cables are connected.

Power surge may cause damage to the Switch.

Power failure

As a precaution, the switch should be unplugged in case of power failure. When power

is resumed, plug the switch back in.

Network connection

Monitor

NVR

PoE IP Camera

CE Mark Warning: This is a Class A product. In home environment, this product may

cause radio interference. In this case, the user may be required to take appropriate

measures.

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is

part of the shipping content. If the Declaration of Conformity is missing, you can

request it by post under the below mentioned manufacturer address.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3, 58513 Lüdenscheid, Germany

Tabla de contenidos

Otros manuales de Cambiar de Digitus

Digitus

Digitus 8/16-Port Combo KVM OSD Switch For Usb And... Manual de usuario

Digitus

Digitus DS-23100-1 Manual de usuario

Digitus

Digitus DN-95354 Manual de usuario

Digitus

Digitus DN-95311 Manual de usuario

Digitus

Digitus DN-651118 Manual de usuario

Digitus

Digitus DA-73300 Manual de usuario

Digitus

Digitus DA-70221 Manual de usuario

Digitus

Digitus DS-12874 Manual de usuario

Digitus

Digitus DS-44100-1 Manual de usuario

Digitus

Digitus DN-95347-1 Manual de usuario

Digitus

Digitus DS-45339 Manual de usuario

Digitus

Digitus DN-651129 Manual de usuario

Digitus

Digitus DA-70246 Manual de usuario

Digitus

Digitus DA-70220 Manual de usuario

Digitus

Digitus DS-45305 Manual de usuario

Digitus

Digitus DA-70135-3 Manual de usuario

Digitus

Digitus DN-80063 Manual de usuario

Digitus

Digitus DS-44100 Manual de usuario

Digitus

Digitus DS-50304 Manual de usuario

Digitus

Digitus DN-95301 Manual de usuario

Digitus

Digitus DA-70247 Manual de usuario

Digitus

Digitus DN-80119 Manual de usuario

Digitus

Digitus Professional DN-60013 Manual de usuario

Digitus

Digitus DN-80069 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario