Digitus DN-80067 Manual de usuario
8-Port Gigabit + 2 Gigabit
SFP Ethernet, Unmanaged Switch
Quick Installation Guide
DN-80067
2
Copyright Statement
Our company reserves all copyrights of this document. Any
reproduction, excerption, backup, modification, transmission,
translation or commercial use of this document or any portion of
this document, in any form or by any means, without the prior
written consent of our company is prohibited.
Exemption Statement
This document is provided "as is". The contents of this document
are subject to change without any notice. Please obtain the latest
information through our company website. Our company
endeavors to ensure content accuracy and will not shoulder any
responsibility for losses and damages caused due to content
omissions, inaccuracies or errors.
Before you install and use this product, please read this manual
carefully for full exploiting the functions of this product.
1. Product Introduction
The Switch is 8 ports 10/100/1000Mbps + 2 ports 100/1000Mbps
SFP Slots Unmanaged Ethernet Switch. This switch is a design of
high integration level, exquisite, portable, easy to operate, which
is suitable for the small and medium office and home network.
The switch provide you with a simple, economic, standard and
high performance of network application plan, it is ideal choice to
promote the department and working group performance. It
provide simple and understood LED indicator light on the front
panel, so that you can quickly judge the working state of the
switch, and help to diagnose the network failure.
3
1.1 Package Content
Before installing the Switch, make sure that the following the
"packing list" listed OK. If any part is lost and damaged, please
contact your local agent immediately. In addition, make sure that
you have the tools install switches and cables by your hands.
1 x 8-Port Gigabit + 2 Gigabit SFP
Ethernet, Unmanaged Switch
1 x Power supply
1 x Quick Start Guide
1.2 Features
Comply with IEEE 802.3, IEEE 802.3u, IEEE802.3x,
IEEE802.3ab standards
Support ports Auto MDI/MDIX
4K entry MAC address table of the switch
with auto-learning and auto-aging
Supports IEEE802.3x flow control for Full-duplex Mode
and backpressure for Half-duplex Mode
Support packet length 9216 bytes jumbo frame packet
forwarding at wire speed
8 x 10/100/1000Mbps Auto MDI/MDI-X Ethernet port
Two 1000Mbps SFP Slots
LED indicators for monitoring Link / Activity/Speed
4
1.3 Hardware Specifications
Standards and Protocols
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab,
IEEE 802.3x, IEEE 802.3z
Interface
8 x 10/100/1000Mbps
Auto-Negotiation ports
2x 1000Mbps SFP ports
Network Media
10BASE-T: UTP category 3, 4, 5 cable
(maximum 100m)
100BASE-Tx:UTP category 5, 5e cable
(maximum 100m)
1000Base-T: UTP category
5e, 6 cable
(maximum 100m)
1000Base-SX: 62.5μm/
50μm MMF (2m~550m)
1000Base-LX: 62.5μm/
50μm MMF (2m~550m)
or 10μm SMF (2m~5000m)
Transfer Method
Store-and-Forward
MAC Address Table
4K
Switching Capacity
20Gbps
Buffer
1.5Mbit
Packet Forwarding
14.88Mpps
Jumbo Frame
9216Bytes
Indicators
Per Device
Power
Per Port
Link/Activity/Speed
Power Supply
12V 1A External Power Supply
5
Power Consumption
Maximum: 5.78W (220V/50Hz)
Dimensions (W x D x H)
190x100x28mm
Environment
Operating Temperature: 0°C~45°C
Storage Temperature: -40°C~70°C
Operating Humidity:
10%~90% non-condensing
Storage humidity:
5%~90% non-condensing
1.4 External Component Description
Front Panel
The front panel of the Switch consists of a series of LED indicators
and 8 x 10/100/1000Mbps RJ-45 ports and two SFP ports.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and
troubleshoot any potential problem with the Switch, connection
or attached devices.
6
The following chart shows the LED indicators of the Switch along
with explanation of each indic a t o r.
Indicator
Faceplate
Marker
Status Indication
PWR
Status Light PWR
Off
Power Off.
Solid
green
Power On.
10/100/1000
BASE-adaptive
Ethernet
port indicator
Link/Act/
Speed
Off
Power Off.
Solid
green
Power On.
Solid
orange
The port is
connected at
100/10Mbps.
Blinking
The port is
transmitting or
receiving data.
SFP port
indicators Link/Act
Off
The port is
NOT connected.
Solid
green
The port is
connected
Blinking
The port is
transmitting or
receiving data.
10/100/1000 Mbps RJ-45 ports (1~8):
Designed to connect to the device with a bandwidth of 10Mbps,
100Mbps, 1000Mbps. Each has a corresponding Link/Act/Speed
indicator.
7
SFP ports (SFP1, SFP2):
The interface card provides an interface so that you can insert a
transceiver module (SFP) into the interface and connect it to the
interface of another switch with cables. Each has a corresponding
Link/Act LED.
Rear Panel
The rear panel of the Switch contains one Grounding Terminal
and DC power adapter
Grounding Terminal:
Located on the right side of the power supply connector, use wire
grounding to lightning protection.
DC Power Connector:
Powered by the external power adaptor, 12V/1A spark-proof
external power supply.
8
2. Installing and Connecting the Switch
This part describes how to install your Ethernet Switch and make
connections to it. Please read the following topics and perform
the procedures in the order being presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect
installation causing device damage and security threat.
Put the Switch on stable place or desktop in case of
falling damage.
Make sure the Switch works in the proper DC input range
and matches the voltage labeled on the Switch.
To keep the Switch free from lightning, do not open the
Switch's shell even in power failure.
Make sure that there is proper heat dissipation from and
adequate ventilation around the Switch.
Make sure the cabinet to enough back up the weight of
the Switch and its accessories.
2.2 Desktop Installation
Sometimes users are not equipped with the 19-inch standard
cabinet. So when installing the Switch on a desktop, please attach
these cushioning rubber feet provided on the bottom at each
corner of the Switch in case of the external vibration. Allow
adequate space for ventilation between the device and the
objects around it.
9
2.3 Wall Installation
The installation process is as follows:
Step one:
Please drill two suitable holes,
press two expansion tubes into
the two holes respectively.
Step two:
Insert the screw into the
expansion tube.
Step three:
Hang the switch on the two
screws.
Step four:
Installation is completed.
10
2.4 Power on the Switch
The Switches connected an external power adapter power
12V/1A supply, make sure you use the proper power supply.
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with
neutral outlet or multifunctional computer professional
receptacle. Please make sure to connect the metal ground
connector to the grounding source on the outlet.
DC Power Adapter Connection:
Connect the DC power connector in the back panel of the Switch
to external receptacle with the included DC Power Adapter and
check the power indicator is ON or not. When it is ON, it indicates
the power connection is OK.
2.5 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network
card driver, please connect one end of the twisted pair to RJ-45
jack of your computer, the other end will be connected to any RJ-
45 port of the Switch, the distance between Switch and computer
is around 100 meters. Once the connection is OK and the devices
are power on normally, the LINK/ACT/Speed status indicator lights
corresponding ports of the Switch.
Tabla de contenidos
Otros manuales de Cambiar de Digitus
Digitus
Digitus DS-45316 Manual de usuario
Digitus
Digitus DS-45320 Manual de usuario
Digitus
Digitus DC-71301 Manual de usuario
Digitus
Digitus DA-73300 Manual de usuario
Digitus
Digitus DS-45339 Manual de usuario
Digitus
Digitus DN-95358 Manual de usuario
Digitus
Digitus DA-70232 Manual de usuario
Digitus
Digitus DN-50021 Manual de usuario
Digitus
Digitus DS-46100 Manual de usuario
Digitus
Digitus DN-95351 Manual de usuario
Digitus
Digitus DS-45334 Manual de usuario
Digitus
Digitus DS-12874 Manual de usuario
Digitus
Digitus DA-73300-1 Manual de usuario
Digitus
Digitus DN-80233 Manual de usuario
Digitus
Digitus DN-651126 Manual de usuario
Digitus
Digitus DN-95320-1 Manual de usuario
Digitus
Digitus 5-Port HDMI Switch Manual de usuario
Digitus
Digitus DN-95320 Manual de usuario
Digitus
Digitus DS-45312 Manual de usuario
Digitus
Digitus DN-80071 BLACK RAPID 1000 Manual de usuario
