DigitaLinx DL-44E-KIT Instrucciones de funcionamiento

11675 Ridgeline Dr
Colorado Springs, CO 80921
Rev 160926 Phone: 719-260-0061
Toll-Free: 800-530-8998
Fax: 719-260-0075
DL-44E-KIT Installaon and
Operaon Guide

DL-44E-KIT Installaon Guide
2

DL-44E-KIT Installaon Guide
3
Important Safety Instrucons
»Please completely read and verify you understand all instrucons in this manual before operang this equipment.
»Keep these instrucons in a safe, accessible place for future reference.
»Heed all warnings.
»Follow all instrucons.
»Do not use this apparatus near water.
»Clean only with a dry cloth.
»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
»Use only accessories specied or recommended by Intelix.
»Explanaon of graphical symbols:
◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle
symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the
product enclosure which may be of sucient magnitude to constute a risk of shock to a person or
persons.
◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended
to alert the user to the presence of important operang and maintenance (servicing) instrucons
in the literature accompanying the product.
»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
»Use the mains plug to disconnect the apparatus from the mains.
»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.
»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of
your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be
maintained.
»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the
point where they exit from the apparatus.
»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.
»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a
cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.
»Unplug this apparatus during lightning storms or when unused for long periods of me.
»Cauon! Shock Hazard. Do not open the unit.
»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

DL-44E-KIT Installaon Guide
4
Table of Contents
Product Overview��������������������������������������������������������������������������������������������������������������������������������������� 6
Package Contents ��������������������������������������������������������������������������������������������������������������������������������������� 6
Front and Rear Panels DL-44E-KIT��������������������������������������������������������������������������������������������������������������� 7
Front Panel���������������������������������������������������������������������������������������������������������������������������������������������������� 7
Rear Panel ����������������������������������������������������������������������������������������������������������������������������������������������������� 7
Front and Rear Panels DL-HD70LS-RX ��������������������������������������������������������������������������������������������������������� 8
Front Panel���������������������������������������������������������������������������������������������������������������������������������������������������� 8
Rear Panel ����������������������������������������������������������������������������������������������������������������������������������������������������� 8
Installaon Instrucons������������������������������������������������������������������������������������������������������������������������������ 9
Mount the Matrix ����������������������������������������������������������������������������������������������������������������������������������������� 9
Usage Precauons ���������������������������������������������������������������������������������������������������������������������������������������� 9
Connecon Procedure����������������������������������������������������������������������������������������������������������������������������������� 9
Connecon with HDBaseT Receiver �������������������������������������������������������������������������������������������������������������� 9
System Operaons ��������������������������������������������������������������������������������������������������������������������������������������10
IR Remote������������������������������������������������������������������������������������������������������������������������������������������������� 10
Control Far-end Device locally���������������������������������������������������������������������������������������������������������������������11
Control Local Device Remotely ....................................................................................................................11
Mulple to Mulple: (IR Matrix) .................................................................................................................11
TCP/IP Control ������������������������������������������������������������������������������������������������������������������������������������������ 12
Controlled by PC������������������������������������������������������������������������������������������������������������������������������������������ 12
Controlled by PC(s) in LAN���������������������������������������������������������������������������������������������������������������������������12
Web Browser Control�������������������������������������������������������������������������������������������������������������������������������� 13
EDID Management ����������������������������������������������������������������������������������������������������������������������������������� 14
EDID learning ��������������������������������������������������������������������������������������������������������������������������������������������14
EDID Invoking���������������������������������������������������������������������������������������������������������������������������������������������� 14
RS232 Commands������������������������������������������������������������������������������������������������������������������������������������� 15
Troubleshoong ��������������������������������������������������������������������������������������������������������������������������������������� 19
Loss of color or no video signal output �������������������������������������������������������������������������������������������������������19
Cannot control the device via front panel buons��������������������������������������������������������������������������������������19
Cannot control the device via IR remote ����������������������������������������������������������������������������������������������������� 19
Cannot control the matrix by control device (e.g. a PC) through RS232 port����������������������������������������������19
Stac becomes stronger when connecng the video connectors ���������������������������������������������������������������19
DL-44E-KIT Technical Specicaons����������������������������������������������������������������������������������������������������������� 20
DL-HD70LS-RX Technical Specicaons ����������������������������������������������������������������������������������������������������� 21

DL-44E-KIT Installaon Guide
5

DL-44E-KIT Installaon Guide
6
The DL-44E-KIT is a professional 4K HDBaseT Home Distribuon Hub Kit, which consists of a 4K HDBaseT Matrix
Switcher, 3 HDBaseT Receivers and accessories. The DL-44E-KIT is a professional 4x4 HDBaseT Matrix Switcher
that consist of the following inputs and outputs, 4 HDMI IN (4kx2K@60Hz signal at max), 3 IR IN, 1 IR EYE, 4 IR
OUT, 3 HDBaseT OUT, 1 HDMI OUT, 1 SPDIF OUT, 1 L&R RCA OUT, and TCP/IP, RS232 control port via phoenix
connector. The DL-44E-KIT oers manual HDCP management and auto-detecng along with easy installaon
with rack-mounng design.
The DL-HD70LS-RX is an HDBaseT Receiver that consists of the following inputs and outputs, 1 HDBaseT IN,
1 IR IN, 1 IR OUT and HDMI OUT. The receiver is powered directly by the DL-44E-KIT. All HDMI inputs can be
selected by either the front panel buons, IR, RS232 or GUI. The selected source is delivered to HDBaseT zoned
outputs 1-3 & HDMI Output.
The DL-44E-KIT is capable of delivering 4K signals up to 40m, 1080p up to 70m and powering the receivers via
a single CAT5e cable. It is recommended to use good quality CAT6 cable. The Matrix Switcher supports EDID
management and is HDCP 2.2, 1.4 compliant. Audio sources can be selected via RS232 commands and TCP/IP
at the Matrix Switcher or by 3rd Party control.
Product Overview
Package Contents
Please verify the following items are in the shipping box prior to installaon of the DL-44E-KIT.
1 x DL-44E-KIT 4K HDBaseT Matrix Switcher,
3 x DL-HD70LS-RX HDBaseT Receivers
1 x Power Adapter (DC 24V 2.71A)
1 x Power Cord(Oponal)
4 x IR Emiers
3 x IR Receivers
1 x IR Receiver(Inserted into IR EYE port)
1 x IR remote
1 x RS232 cable(Phoenix to 9-pin D-Sub)
2 x Mounng ears & 6 x Screws (For DL-44E-KIT 4K HDBaseT Matrix Switcher )

DL-44E-KIT Installaon Guide
7
DL-44E-KIT Front and Rear Panels
Front Panel
Rear Panel
FIRMWARE
OUTPUT 1
IN PUT TO
1 2 3 4
OUTPUT 2
IN PUT TO
1 2 3 4
OUTPUT 3
IN PUT TO
1 2 3 4
OUTPUT 4
IN PUT TO
1 2 3 4
13
24
1-HDBT
IR OUT
IR E YE
2-HD BT 4-SPDIF4-HDMI
3- HDBT L R
4 DC 24V TCP/I P
RxTx
RS 232
POWER CONTR OL
IR IN
1 2 3
4
1 2 3
HD MI 1 HD MI 2 HD MI 3 H DMI 4
INPUTS OUTPUTS
3
4
25
16
1. FIRMWARE
2. Power Indicator
3. INPUT Selector Indicators
4. Output selector buon
1. HDMI INPUTS
2. IR IN
3. IR OUT
4. OUTPUTS
5. TCP/IP and RS232 Control
6. DC 24V

DL-44E-KIT Installaon Guide
8
DL-HD70LS-RX Front and Rear Panels
Front Panel
Rear Panel
IR IN IR OUTHDMI OUT
123
Link HDCP
12V DC
12
1. HDMI OUT
2. IR IN
3. IR OUT
1. Power Indicator
2. TP IN
The RJ45 socket has two LED status indicators. Plug in the Pre-installed CAT cable in to the HDBT RJ45 socket.
HDCP: HDCP compliant indicator, OFF: No HDMI trac (no picture), GREEN: Signals with HDCP, Blinking GREEN:
Signal without HDCP.
LINK: HDBT Link status indicator. OFF: No Link, YELLOW:Link Successful, Blinking YELLOW: Link Error.

DL-44E-KIT Installaon Guide
9
Installaon Instrucons
Mount the Matrix
At least 2 inches of free air space is required on both sides of the DL-44E-KIT for proper side venlaon. Avoid
mounng the DL-44E-KIT near a power amplier or any other source of signicant heat.
1. The DL-44E-KIT 4K Home Distribuon kit should be installed in a clean and dust free environment.
2. Ensure that all plugs, power cords and sockets are in good condion without signs of damage.
3. All devices should be connected before power on.
Usage Precauons:
Connecon Procedure:
1. Connect HDMI sources (e.g. DVD) to HDMI input ports of the Matrix Switcher via good quality HDMI
cables.
2. Connect the Pre-Installed CAT5e/CAT 6 cable infrastructure to the DL-44E-KIT Matrix Switcher and
HDBaseT receivers DL-HD70LS-RX via good quality patch leads.
3. Connect HDTV to HDMI output port via HDMI cable.
4. Plug in an HDMI cable in to each of the DL-HD70LS-RX and connect to the local display [HDTV].
5. Connect AVR amplier to SPDIF output port or via the Toslink opc bre cable.
6. Connect speaker to L&R (RCA) output port via audio cable.
7. Plug the IR Receivers 3.5mm jack into the IR IN sockets on the DL-HD70LS-RX and plug in the IR Emiers
to the IR OUT sockets (1-4) on the Matrix Switcher to make up as an IR Matrix.
8. Plug the phoenix connector in to the RS232 socket on the matrix, this will enable the Matrix Switcher to
be controlled via a PC.
9. Plug in a Patch lead from the router in to the Ethernet port on Matrix Switcher to control Matrix Switcher
by TCP/IP protocol.
10. Plug in the Power supply adapter 24V DC and ghten to secure. Once all components have been
connected and the installaon is completed, turn on the power.
Connecon with HDBaseT Receiver:
1. The Matrix Switcher has 3 HDBaseT outputs which support PoC technology.
2. Plug in the 4 RJ45 patch leads in to the HDBT outputs and connect to the pre-installed infrastructure.
3. Connect the DL-HD70LS-RX HDBaseT Receivers to the pre-installed cabling via addional patch leads.
4. Plug the power supply in to the power socket on the matrix, the DL-HD70LS-RX will be powered by the
Matrix Switcher.

DL-44E-KIT Installaon Guide
10
System Operaons
The Matrix Switcher can be controlled via the front panel. Please follow the basic programing instrucons
below:
1. To convert one input to an output:
Example: Input 1 to Output 3
-Press INPUTS 1 + OUTPUTS 3 + ENTER
2. To convert an input to several outputs:
Example: Convert Input 2 to Output 3 and 4
-Press INPUTS 2 + OUTPUTS 3 + OUTPUTS 4 + ENTER
3. To convert an input to all outputs:
Example: Input 1 to all Outputs
-Press INPUTS 1 + ALL + ENTER
IR Remote
Connect an IR receiver to the IR EYE port of the Matrix Switcher, users can control it through the included IR
remote. Here is a brief introducon to the IR remote.
Standby buon, press it to enter/ exit standby mode.
INPUTS: Input channel selecon buons, range from 1-4, corresponding IR signal switched
synchronously when switching input channels.
OUTPUTS: Output channel selecon buons.
Menu buons: ALL, EDID, CLEAR and ENTER.
-ALL: Select all outputs.
-EDID management buon: Enable input port to manually capture and learn the EDID data
of output devices.
-CLEAR: Withdraw an operaon like switching output channel, learning EDID data before it
comes into eect. Meanwhile, the matrix will return to the previous status.
-ENTER: Conrm operaon.
Tabla de contenidos
Otros manuales de Conmutador de matriz de DigitaLinx

DigitaLinx
DigitaLinx DL-HDM44 Manual de usuario

DigitaLinx
DigitaLinx DL-HDM44-FS Instrucciones de funcionamiento

DigitaLinx
DigitaLinx DL-HDM88A-H2 Manual de usuario

DigitaLinx
DigitaLinx DL-A31 Manual de usuario

DigitaLinx
DigitaLinx DL-HDM88-SS Instrucciones de funcionamiento

DigitaLinx
DigitaLinx DL-HDM88A-H2 Manual de usuario

DigitaLinx
DigitaLinx DL-A51 Manual de usuario

DigitaLinx
DigitaLinx DL-HDM88-FS Instrucciones de funcionamiento

DigitaLinx
DigitaLinx DL-S42-H2 Manual de usuario

















