Digital Watchdog DWC-PB6M4T Manual de usuario

Quick Start Guide

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00AM – 8:00PM EST, Monday thru Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

‘Search by Product’ search bar. Results for applicable

part numbers will populate automatically based on the

part number you enter.

3. Click ‘Search’. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

DWC-PB6M4T

Default Login Information

Username: admin Password: admin

WHAT’S IN THE BOX

Quick

setup

guide

1Sunshield

screws 1 Set

Mounting

template 1

Screws and

plastic

anchors – 4pcs

1 Set

Sunshield 1T-Wrench 1

1. Once all cables are connected, secure the camera to the mounting surface using the included screws.

2. To adjust the camera’s pan and tilt, loosen the pan/tilt stopper screw. Adjust the camera’s position as needed.

You may use the camera’s video test cable for local image view.

3. Attach the sunshield to the camera by using the provided sunshield screws.

1. The mounting surface must bear ﬁve times the weight of your

camera (2.2 lbs).

2. Mind the cables and power line to avoid damage.

3. CAUTION: These servicing instructions are for use by qualiﬁed

service personnel only. To reduce the risk of electric shock do not

perform any servicing other than that contained in the operating

instructions unless you are qualiﬁed to do so.

4. This product is intended to be supplied by a UL Listed Power

Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc,

880 mA min.

5. The wired LAN hub providing power over the Ethernet (PoE) in

accordance with IEEE 802-3af shall be a UL Listed device with

the output evaluated as a Limited Power Source as deﬁned in

UL60950-1 or PS2 as deﬁned in UL62368-1.

6. Unit is intended for installation in a Network Environment 0 as

deﬁned in IEC TR 62102. As such, associated Ethernet wiring shall

be limited to inside the building.

7. Using the mounting template sheet or the camera itself, mark and

drill the necessary holes in the wall or ceiling.

Pass the wires through the mount bracket and make all

necessary connections.

a. NETWORK CONNECTIONS – If you are using a PoE Switch,

connect the camera using an Ethernet cable for both data

and power.

b. NETWORK CONNECTIONS – If you are using a non-PoE

switch, connect the camera to the switch using an Ethernet

cable for data transmission and use a power adapter to power

the camera.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES

Power requirements Power consumption

DC12V, PoE IEEE 802.3at

Class 3

(adapter not included)

TDN On: MAX 10.1W

TDN O: 7.7W

STEP 3 – INSTALLING THE CAMERA

AUDIO

INPUT

AUDIO

OUTPUT

POWER

NET WORK

ALARM

OUTPUT

ALARM

INPUT

ILLUMINATOR

Reset

Button

SD Card Slot

Test Video Output

Rev Date: 04/19

Speciﬁcations and pricing are subject to change without notice.

Quick Start Guide

STEP 6 – DW IP FINDER™

Network Setup

1. To install the DW IP Finder™, go to:

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page

and press Enter.

3. Click on the DW IP Finder from the search result and go to

Software tab. Click on download icon to download the DW IP

Finder installation ﬁle.

4. Run the installation ﬁle and follow the wizard to install the DW

IP Finder™. Open the DW IP Finder™ and click ‘Scan Devices’. It

will scan the selected network for all supported devices and list

the results in the table. During the scan, the DW logo will

turn gray.

Default ID / PW : admin / admin

‘Port forwarding’ has to be set in your

network’s router for external access

to the camera.

*NOTE: For security purposes, it is highly

recommended to change your

password after initial setup.

Default TCP/IP information: DHCP

Select DHCP if the internet service is dynamic IP. This will allow the

camera to receive its IP address from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)

Netmask, Gateway and DNS information.

* The camera’s IP must be set to Static if connecting to

DW Spectrum

Contact your network administrator for more information.

Thumbnail view

Firmware version

Camera’s uptime

Open Device

conﬁguration

settings

Filter device type to scan

Scan devices

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk IP assignment

Firmware upgrade

Device’s

information

5. Select a camera from the list by double-clicking on the

camera’s image or clicking on the ‘Click’ button under the

IP Conf. column. The pop-up window will show the camera’s

current network settings, allowing admin users to adjust the

settings as needed.

6. To access the camera’s web page, click on ‘View

Camera Website’.

7. To save the changes made to the

camera’s setting, input username and

password of the camera and click Apply.

Click “Scan Devices” from the

main screen again to display the

updated information.

Use the DW IP Finder™ software to scan the network and detect all MEGApix®cameras, set the camera’s network settings or access the camera’s web client.

STEP 7 – WEB VIEWER

STEP 4 – MANAGING THE SD CARD

STEP 5 – RESETTING THE CAMERA

To install the memory card (not included):

1. To install the camera’s SD Card, locate the SD card slot in the side

of the camera by unscrewing

the con cap.

2. Insert class 10 SD/SDHC/SDXC card into the SD card slot by

pressing the SD card until clicks.

3. To remove the SD card, press the card inward until it clicks to

release from the card slot then pull out from the slot

To reset the camera, use the tip of a paper clip or a pencil and press

the reset button. Pressing the button for ﬁve (5) seconds will initiate a

camera-wide reset of all the settings, including network settings.

Con Cap SD Card Slot

Reset Button

Once the camera’s network settings have been setup properly, you

can access the camera’s web viewer using the DW IP Finder™.

To open the camera’s web viewer:

1. Find the camera using the DW IP Finder™.

2. Double-click on the camera’s view in the results table.

3. Press the ‘View Camera Website’. The camera’s web viewer will

open up in your default web browser.

4. Enter the camera’s username and password

(default are admin / admin).

5. If you are accessing the camera for the ﬁrst time, install the

ActiveX ﬁles in order to view video from the camera.

The GUI display may dier by camera models.

NOTE: Please see the full product manual for web viewer setup,

functions and camera settings options.

NOTE: Some Menu options may not be available based on the

camera model. See the full manual for more information.

Otros manuales para DWC-PB6M4T

Otros manuales de Cámara de seguridad de Digital Watchdog

Digital Watchdog

Digital Watchdog DWC-V3363D Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MPF5Wi4TW Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light Plus Universal HD over Coax... Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MB75Wi4T Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MT94WiAT Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPix DWC-MB62DiVT Manual de usuario

Digital Watchdog

Digital Watchdog DWC-PTZ10x Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix Ai DWC-XSDE08Mi Manual de usuario

Digital Watchdog

Digital Watchdog DWC-B562DIR Manual de usuario

Digital Watchdog

Digital Watchdog Starlight V3363D Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix Flex DWC-PVX16W2 Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix MPTZ5X Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MV421D Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-V7553W Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT 960H DWC-V6553D Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPIX DWC-MF4Wi4 Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-D3863WTIRW Manual de usuario

Digital Watchdog

Digital Watchdog Infinity B1367WTIR650 Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPIX PANO DWC-PVF5M1TIR Manual de usuario

Digital Watchdog

Digital Watchdog B1362TIR650 Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT Flex DWC-VS753WT2222 Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-B7553TIR Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT AHD DWC-D3763TIR Manual de usuario

Digital Watchdog

Digital Watchdog Snapit DWC-D4363D Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario