Power
Ethernet cable
Ethernet cable
Rev Date: 04/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Quick Start Guide
STEP 6 – DW IP FINDER™
Thumbnail view
Firmware version
Camera’s uptime
Open Device
configuration
settings
Filter device type to scan
Scan devices
Select network to scan
Show/hide thumbnail view
Refresh thumbnail view
Bulk IP assignment
Firmware upgrade
Device’s
information
Use the DW IP Finder™ software to scan the network and detect all MEGApix®cameras, set the camera’s network settings or access the camera’s web client.
STEP 7 – WEB VIEWER
STEP 4 – CABLING
STEP 5 – MANAGING THE SD CARD
Use the diagram below to properly connect power, network, audio,
alarm and sensors to the camera.
1. To install the camera’s SD Card, locate the SD card slot in the
bottom of the camera by unscrewing the con cap.
2. Insert class 10 SD/SDHC/SDXC card into the SD card slot by
pressing the SD card until clicks.
3. To remove the SD card, press the card inward until it clicks to
release from the card slot than pull out from the slot.
Using a PoE Switch or PoE
Injector
Not using PoE Switch or PoE
Injector
NOTE: Maximum SD Card size supported: 64GB.
When inserting the SD card into the card slot, the SD
card’s contacts should be facing upward, as shown in
the diagram.
4Alarm In
DI: Orange
DI COM: Yellow
DO1(N.O.): Green
DO1 COM: Blue
3Alarm Out
1Audio In
(WHITE Jack)
2Audio Out
(RED Jack)
NOTE: Please see the full product manual for web viewer setup,
functions and camera settings options.
NOTE: Some Menu options may not be available based on the
camera model. See the full manual for more information.
*
The GUI display may dier by camera models.
Once the camera’s network settings have been setup properly, you
can access the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will
open up in your default web browser.
4. Enter the camera’s username and password
(default are admin / admin).
5. If you are accessing the camera for the first time, install the VLC
player for web files in order to view video from the camera.
Network Setup
1. To install the DW IP Finder™, go to:
http://www.digital-watchdog.com
2. Enter “DW IP Finder” on the search box at the top of the page
and press Enter.
3. Click on the DW IP Finder from the search result and go to
Software tab. Click on download icon to download the DW IP
Finder installation file.
4. Run the installation file and follow the wizard to install the DW
IP Finder™. Open the DW IP Finder™ and click ‘Scan Devices’. It
will scan the selected network for all supported devices and list
the results in the table. During the scan, the DW logo will
turn gray.
Default ID / PW : admin / admin
‘Port forwarding’ has to be set in your
network’s router for external access
to the camera.
*NOTE: For security purposes, it is highly
recommended to change your
password after initial setup.
Default TCP/IP information: DHCP
Select DHCP if the internet service is dynamic IP. This will allow the
camera to receive its IP address from the DHCP server.
Select “Static” to manually enter the camera’s IP address, (Sub)
Netmask, Gateway and DNS information.
* The camera’s IP must be set to Static if connecting to
DW Spectrum
Contact your network administrator for more information.
5. Select a camera from the list by double-clicking on the
camera’s image or clicking on the ‘Click’ button under the
IP Conf. column. The pop-up window will show the camera’s
current network settings, allowing admin users to adjust the
settings as needed.
6. To access the camera’s webpage, click on ‘View
Camera Website’.
7. To save the changes made to the
camera’s setting, input username and
password of the camera and click Apply.
Click “Scan Devices” from the
main screen again to display the
updated information.
