Digital Watchdog D4252 Series Manual de usuario

D4252 Series

About manual

INSTRUCTION MANUAL

Before installing and using the camera, please read this

manual carefully.

Be sure to keep it hand

for future reference.

5436 W Crenshaw Street

Tampa, FL 33634

www.digital-watchdog.com

Technical Support : 1-866-446-3595 / 813-888-9555

Before installing and using the camera, please read this

manual carefully.

Be sure to keep it handy for future reference.

5436 W Crenshaw Street

Tampa, FL 33634

www.digital-watchdog.com

Technical Support : 1-866-446-3595 / 813-888-9555

PRECAUTIONS

Before installing and using the camera, please read this manual

carefully.

Be sure to keep it handy for later reference.

UNPACKING

Care should be taken when the unpacking the shipped unit.

Check the parts list and confirm all items are included in.

Contact … .. If a problem is noted.

■Do not open or modify

Do not open the case except during maintenance and installation,

as it may be dangerous and may damage the product.

■Do not put objects inside the unit

Make sure that no metal objects or flammable substances

enter the camera as it can cause fire, short-circuits, or permanent

damage.

■Be careful when handling the unit

To prevent damage, do not drop the camera or subject it to

strong shock or vibration

■Install away from electric or magnetic fields.

■Protect from humidity and dust

■Protect from high temperature

Be careful when installing on the ceiling in a kitchen or boiler

room, as the temperature may damage the camera.

■Cleanin

Before installing and using the camera, please read this manual

carefully.

Be sure to keep it handy for later reference.

UNPACKING

Care should be taken when the unpacking the shipped unit.

Check the parts list and confirm all items are included in.

Contact … .. If a problem is noted.

■Do not open or modify

Do not open the case except during maintenance and installation,

as it may be dangerous and may damage the product.

■Do not put objects inside the unit

Make sure that no metal objects or flammable substances

enter the camera as it can cause fire, short-circuits, or permanent

damage.

■Be careful when handling the unit

To prevent damage, do not drop the camera or subject it to

strong shock or vibration

■Install away from electric or magnetic fields.

■Protect from humidity and dust

■Protect from high temperature

Be careful when installing on the ceiling in a kitchen or boiler

room, as the temperature may damage the camera.

■Cleaning

Dirt can be removed from the case only by wiping it with a soft cloth

moistened with a soft detergent solution.

■Mounting Surface

The mounting surface must be strong enough to support

the camera.

TROUBLESHOOTING

Before sending the camera out for repair, check the items below.

If the problem persists after checking these items, contact your

service center.

■If no image appears

Is the coaxial cable attached securely?

Is the power and voltage within operational specification?

Has the iris of the lens been adjusted correctly (within specification

levels?

Is there adequate illumination?

■If the image is unclear

Is the lens in focus?

Is the lens dirty?

Dirt or fingerprints on the lens can adversely affect the

image. Gently wipe any dirt or fingerprints off the lens

with a soft cloth or lens cleaning paper and cleaning

Before sending the camera out for repair, check the items below.

If the problem persists after checking these items, contact your

service center.

■If no image appears

Is the coaxial cable attached securely?

Is the power and voltage within operational specification?

Has the iris of the lens been adjusted correctly (within specification

levels?

Is there adequate illumination?

■If the image is unclear

Is the lens in focus?

Is the lens dirty?

Dirt or fingerprints on the lens can adversely affect the

image. Gently wipe any dirt or fingerprints off the lens

with a soft cloth or lens cleaning paper and cleaning

fluid (commercially available).

Is the monitor adjusted correctly?

WARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE

DIMENSION (mm)

INSTALLATION

A. Separate the dome cover from the bottom

case .

B. Cut the hole in the ceiling for routing the

cables.

C. Align the camera unit with the surface of the

ceiling, make two marks, and then drill the two

holes.

D. Pass the power cable and video cable

through the cable hole in the ceiling.

E. Match two holes of camera unit with the holes

in the ceiling and then fix the camera unit by

tightening screws .

F Carry out the settings and adjustment for the

A. Separate the dome cover from the bottom

case .

B. Cut the hole in the ceiling for routing the

cables.

C. Align the camera unit with the surface of the

ceiling, make two marks, and then drill the two

holes.

D. Pass the power cable and video cable

through the cable hole in the ceiling.

E. Match two holes of camera unit with the holes

in the ceiling and then fix the camera unit by

tightening screws .

F. Carry out the settings and adjustment for the

camera.

G. Arrange the lens along with the black dome

insert and then fix the dome cover to the

camera unit .

DC12V

CONNECTION

CAUTION :

Check for polarity when using a DC 12V power supply.

LENS ADJUSTMENT

1. Isolate the dome cover from bottom case.

2. Loosen the module bracket by using screw driver.

3. Adjust the camera module to the desired position and then fix the module

bracket by using a screw driver.

4. Assemble the dome cover with the bottom case.

●Selecting Mirror Mode

OFF

CAMERA SETTINGS

OFF

●Compensating for backlight

OFF

WARRANTY INFORMATION

Digital Watchdog (referred to as “the Warrantor”) warrants the Camera

Series against defects in materials or workmanship as follows:

LABOR: For the initial five (5) years from the date of original purchase, if the

camera is determined to be defective, the Warrantor will repair or replace the

unit, with new or refurbished product at its option, at no charge.

PARTS: In addition, the Warrantor will supply replacement parts for the initial

five (5) years.

To obtain warranty or out of warranty service, please contact a Technical

Support Representative at 1-866-446-3595 Monday through Friday from 9:00

AM to 5:00 PM Eastern. A purchase receipt or other proof of the date of the

original purchase is required before warranty service is rendered. This

warranty only covers failures due to defects in materials and workmanship

which arise during normal use. This warranty does not cover damage which

occurs in shipment or failures which are caused by products not supplied by

the Warrantor or failures which result from accident, misuse, abuse, neglect,

mishandling misapplication alteration modification faulty installation set