Digicom LCM16P Manual de usuario

LCM16P

LCM16PR

USER'S MANUAL

III

LCM16P

LCM16PR

USER'S MANUAL

LCM16P LCM16PR rev.2.0 07/97 COD.7D0894

or trasmitted in any form or by any means, electronic, otherwise, without the prior written

permission of the publishers.

The contents of this booklet may be modified without prior permission.

Every possible care has been taken in testing and putting together all the documentation

contained in this booklet, however DIGICOM can not take any responsibility brought by

the use of this booklet.

INDEX

PRECAUTIONS

1. INTRODUCTION 1.1

1.1. PRODUCT FEATURES 1.1

1.2. TECHNICALCHARACTERISTICS 1.1

1.2.1. DTE-DCE digital interface 1.1

1.2.2. Data input 1.2

1.2.3. Clock signal characteristics 1.4

1.2.3. RTS/ CTS circuits 1.4

1.2.4. Asynchronous Mode 1.5

1.2.5. Analog Interface: transmission line 1.5

1.2.6. Analog Interface: receive line 1.5

1.2.7. Receive time base (synchronous mode only) 1.6

1.2.8. C109 Circuit 1.6

1.2.9. Tests 1.7

1.2.10. Connection distance 1.7

1.2.11. Line connection 1.8

1.2.12. DTE connection 1.8

1.3. FUNCTIONAL BLOCK DIAGRAM 1.8

1.3.1. Datapump 1.8

1.3.2. Microprocessor 1.8

1.3.3. Line Interface 1.9

1.3.4. RS 232 Interface 1.9

1.3.5. Power supply circuit 1.9

1.3.6. Loop circuits 1.9

1.4. TRANSMISSION CIRCUIT 1.11

1.4.1. Digital section 1.11

1.4.2. Analog section 1.12

1.5. RECEIVER CIRCUIT 1.13

1.5.1. Analog section 1.13

1.5.2. Digital section 1.13

1.6. POWER SUPPLY 1.14

1.7. CCITT V54 RECOMMENDATION 1.14

2. THIS CHAPTER IS INTENTIONALLY BLANK 2.1

3. OPERATION MODE 3.1

3.1. DEVELOPMENT AND ACCESSORY 3.1

3.1.1. Technical characteristics 3.1

3.1.1.1. Mechanical Size 3.1

3.1.1.3. Power supply 3.2

3.2. COMMAND AND MESSAGE DEVICES 3.2

3.3. INSTALLATION PROCEDURE 3.4

LCM16P LCM16PR Index

3.3.1. Preliminary Operations 3.4

3.3.2. Modem installation 3.4

3.3.3. Electrical connections 3.4

3.3.3.1. Main power supply connection 3.4

3.3.3.2. Line connection 3.5

3.3.3.3. DTE interface 3.5

3.4. LCM16P AND LCM16PR PREDISPOSITION 3.5

3.4.1. Functional Description 3.6

3.4.2. Jumpers functional description 3.12

4. DIAGNOSTIC 4.1

4.1. INTRODUCTION 4.1

4.2. LOOP 3 ACTIVATION 4.1

4.3. LOCAL LOOP 2 ACTIVATION 4.2

4.4. REMOTE LOOP 2 ACTIVATION 4.2

4.5. TANDEM CONFIGURATION EXAMPLE 4.4

4.6. TEST DURING LOOP 4.5

DECLARATION OF CONFORMITY

TABLES INDEX

Tab.: 1.1. CCITT V24 INTERFACE SIGNALS USED IN LCM16P AND

LCM16/PR MODEMS 1.3

Tab.: 1.2. DELAY TIMES RTS/CTS 1.4

Tab.: 1.3. DCD DELAY TIME. 1.6

Tab.: 1.4. CONNECTION DISTANCE WITHOUT THE EQUALIZER 1.7

Tab.: 1.5. CONNECTION DISTANCES WITH EQUALIZER 1.7

PICTURES INDEX

Fig.: 1.1. FUNCTIONAL BLOCK DIAGRAM 1.10

Fig.: 1.2. MODULATION WAVEFORMS 1.11

Fig.: 1.3. BLOCK DIAGRAM 1.16

Fig.: 3.1. LCM16P FRONTAL VIEW 3.3

Fig.: 3.2. LCM16P BACK VIEW 3.3

Fig.: 3.3. LCM16PR FRONTAL VIEW 3.4

Fig.: 3.4. LINE CONNECTOR AND PINS ASSIGNMENT FOR LCM16P 3.5

Fig.: 3.5 LINE CONNECTOR AND PINS ASSIGNMENTS FOR LCM16PR 3.5

Fig.: 3.6. LCM16P TOPOGRAPHICAL VIEW 3.14

Fig.: 3.7. LCM16PR TOPOGRAPHICAL VIEW 3.15

Fig.: 4.1. LOOP 3 DIAGRAM 4.1

Fig.: 4.2. LOCAL LOOP2 DIAGRAM 4.2

Fig.: 4.3. REMOTE LOOP 2 DIAGRAM 4.3

Fig.: 4.4. TANDEM CONNECTION + MULTI- POINT 4.4

LCM16P LCM16PR Index

LCM16P LCM16PR ENGLISH Index

PRECAUTIONS

The following installation rules should be respected in order to have the best working order of the

equipment an user’s safety.

Enviromental Conditions

Forall devices:

ENVIROMENTAL RELATIVE

TEMPERATURE HUMIDITY

from -5 to + 45°C from 20 to80% n.c.

Avoid rapid changes of temperature and humidity (0,03°C/ [min.]).

This system, including cables, should be installed in an area without or distant from:

lDust, humidity, elevated heat from direct sun light.

lObjects irradiating heat. These could cause damages to the container or other problems.

lObjects that cause a strong electromagnetic field. (HI-FI loudspeakers, Etc.).

lLiquids or chemical corrosive substances.

GENERALWARNINGSForallequipmentpowereddirectlyfromthenetwork

POWER SUPPLY 230 Volt 50Hz

ISOLATION CLASS only those indicated on the equipments label

NOMINAL CURRENTS only those indicated on the equipments label

To avoid electric shocks, the equipment should never be opened. Ask qualified personnel help.

To replace the fuse, remove the power supply cable.

Disconnect the power cable from the wall plug when the terminal is not used for a long period.

To disconnect the cable, pull it by the plug, never pull it by the cable itself.

If there should be a liquid or objet penetration in the equipment, disconnect the power cable and call the

qualified personnel for testing.

CLEANINGTHETERMINAL

Use a soft dry cloth. Wet the cloth with water or natural detergent if it is necessary to remove stains.

Never use chemical product such as petrol or solvents.

VIBRATIONS OR CRASHES Caution against vibrations and crashes.

WARNING

This is a class A product.

In a domestic environment this product may cause radio interference

in which case the user may be required to take adeguate measures.

SEDE LEGALE, DIREZIONE ed UFFICI

REGISTERED AND HEAD OFFICE

ITALY - 21010 Cardano al Campo VA

Via Alessandro Volta 39

Tel. 0331/702611 - Fax 0331/263733

Tel. +39/331/702611 - Fax +39/331/263733

http://www.digicom.it

ROMA

00194 Roma Via Dei Colli Della Farnesina 72

Tel. 06/36300015 - Fax 06/3293695

Tel. +39/6/36300015 - Fax +39/6/3293695

BOLOGNA

40122 Bologna Via Lame 116

Tel. e Fax 051/ 558709

Tel. and Fax +39/51/558140

TORINO

10129 Torino C.so De Gasperi 26

Tel. 011/504802 Fax 011/504627

Tel. +39/11/504802 Fax +39/11/504627

PADOVA

35030 Rubano PD Via Della Provvidenza 37

Tel. 049/8976528 Fax 049/8976524

Tel. +39/49/8976528 Fax +39/49/8976524

HOT LINE

Tel. 0331/261649 Fax 0331/730800

Tel. +39/331/261649 Fax +39/331/730800

1.1

LCM16P/LCM16PR Introduction

Digicom SpA

1. INTRODUCTION

1.1. PRODUCT FEATURES

The digicom LCM16P is a baseband modem in table top or rack version.

It is possible to use LCM16 modem in systems of dedicated point to point,

multiple point and tandem two or four wire lines.

The line must have metallic continuity.

Do not insert channel amplifiers on the line.

Isitpossible toactivateremote digitalloop(Loop 2 “RDL”)andremote loop

3 for tandem configuration in accordance with CCITT V.54 standard.

It supports both asynchronous and synchronous communication modes.

DTE interface speed is from 225 up to 19200 bit/s, with a set of intermediate

speeds for the asynchronous mode.

Modulation and demodulation, synchronous to asynchronous conversion,

interfacesignaldelay,loopsandtime-outsareimplementedbyanewintegrated

ASIC circuit.

The LCM16P was designed in accordance with the Telecommunication

standard Nr. 687.

The modemrespects the normativeEN60950, EN41003 (safety standards)

and EN55022 EN50082-1 (electromagnetic compatibility standards). It

complies with V.24, V.28, and V54 CCITT recommendations and with

ISO2110 standard.

1.2. TECHNICAL CHARACTERISTICS

1.2.1. DTE-DCE digital interface

DTE(DataTerminalEquipment)isthedevice inwhichdata aregeneratedand used.

DCE (Data Circuit Terminating Equipment) is the device in which data are

converted from digital to analog and vice versa.

DTE-DCE interface data signal table

CCITT V28 signal level -3 ÷ -25 V; +3 ÷ +25 V

Binarydenomination BIT 1; BIT 0

Data type MARK (MK); SPACE (SP)

Asynchronousbit STOP (Z); START (A)

Control signal state PAUSE (OFF); WORK (ON)

1.2

LCM16P/LCM16PR Introduction

Digicom SpA

1.2.2. Data input

Synchronous mode operation speed

19200, 14400, 9600, 7200, 4800, 3600, 2400,

1800, 1200, 900, 600, 450, 300, 225 bit/s. It is

possible to change speed by the internal dip

switches.

Asynchronous mode operation speed

19200, 14400, 9600, 7200, 4800, 3600, 2400,

1800, 1200, 900, 600, 450, 300, 225 bit/s, with

extension to the following speeds:

Predisposition Minimumvalue Maximum value

300 292,5 (297,5) 301 (305,25)

600 585 (595) 602 (610,5)

1200 1170 (1190) 1204 (1221)

2400 2340 (2380) 2408 (2442)

4800 4680 (4760) 4816 (4884)

9600 9360 (9520) 9632 (9768)

19200 18720 (19040) 19264 (19536)

(Between parenthesis the extension value)

Type of characters no limit; the modem is transparent to the data

comingthrough.

Interface connector 25 leads female cannon with contacts in

accordance with ISO 2110 standard and CCITT

V24 recommendation.

1.3

LCM16P/LCM16PR Introduction

Digicom SpA

Cont. Circuit Direction Mnem. Description

Conn. V24 RS232 DTE-LCM16 Abbrev.

1 - AA <----> PG Earth protection

2 103 BA -----> TD Transmission data

3 104 BB <----- RD Received data

4 105 CA -----> RTS Request to send

5 106 CB <----- CTS Clear to send

6 107 CC <----- DSR Data set Ready

7 102 AB <----> SG Ground

8 109 CF <----- DCD Data carrier detect

9 - - <----- - + 12 volt

10 - - <----- - - 12 volt

15 114 dB <----- TC Transmission Clock

17 115 DD <----- RC Receiver Clock

18 141 CN -----> L3 Local analog loopback

application(CCITTLOOP3)

20 108.2 CD -----> DTR Data terminal ready

21 140 CF -----> RDL Local digital loopback

application (CCITT LOOP

2LOCAL)

22 125 CE <----- - 12 volt

24 113 From -----> ETC External transmission clock

25 142 - <----- TI Active Loop

NOTE: 1, 11, 12, 13, 14, 16, 19, 23 pins are not connected.

Tab.: 1.1. CCITT V24 INTERFACE SIGNALS USED IN LCM16P AND

LCM16/PR MODEMS

Otros manuales para LCM16P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Digicom

Digicom

Digicom Tintoretto Manual de usuario

Digicom

Digicom pocket GSM Manual de usuario

Digicom

Digicom WinModem V.92 Manual de usuario

Digicom

Digicom Pocket GPRS Power Manual de usuario

Digicom

Digicom Michelangelo Gateway Manual de usuario

Digicom

Digicom BlueGATE Manual de usuario

Digicom

Digicom Michelangelo Gateway Manual de usuario

Digicom

Digicom GPRS Bulk Micro QB Manual de usuario

Digicom

Digicom SNM50 Manual de usuario

Digicom

Digicom PALLADIO ISDN Manual de usuario

Digicom

Digicom Michelangelo LAN C Manual de usuario

Digicom

Digicom Tintoretto LAN+ Manual de usuario

Digicom

Digicom COMSPHERE 3910 Manual de usuario

Digicom

Digicom Botticelli Web 8E4079 Manual de usuario

Digicom

Digicom SNM15 Manual de usuario

Digicom

Digicom HDSL Manual de usuario

Digicom

Digicom HSDPA Manual de usuario

Digicom

Digicom Palladio USB Bluetooth Manual de usuario

Digicom

Digicom Michelangelo Gateway Manual de usuario

Digicom

Digicom Donatello Memory ISDN Modem Manual de usuario

Digicom

Digicom Tintoretto LAN Plus ISDN LAN Modem Manual de usuario

Digicom

Digicom SNM46F Manual de usuario

Digicom

Digicom Palladio USB Bluetooth Manual de usuario

Digicom

Digicom Tiziano 56 Memory Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario