Digi TransPort WR21 Manual de usuario
Quick Start Guide
TransPort® WR21
Welcome to your Digi product
Get started: This guide helps you with initial product setup. Need more? Find additional
product support at www.digi.com/support/TransPortWR21. Or connect to the online
documentation by scanning this code:
Digi Technical Support: Digi offers multiple support plans to help you get the most out of your
product. For information on Technical Support plans and pricing, contact us at 877.912.3444 or
visit www.digi.com/support.
Documentation Feedback: To provide feedback on this documentation, send your comments
to techcomm@digi.com.
1Verify your components
Optional provided equipment Required additional equipment
Your box may contain additional cables or antennas, based on your
model and configuration options.
Verify that you have all included equipment. If any item is missing or damaged, contact your supplier.
2Connect the hardware
1. Insert the SIM card(s) into the SIMsockets. For SIM 1, the contacts must be face
down.
For SIM 2, the contacts must be face up. Insert the SIM cards with the chamfered
corner first.
2. Connect the cellular antenna to the WWAN PRIMARY connector on the unit. If the
unit is equipped with a secondary cellular antenna connector, connect it to the
WWANSECONDARY connector.
3. Connect one end of the Ethernet cable to the LAN 0 port on the unit and the
other end to a LANport on a PC.
4. Connect the power supply. Depending on model, the unit either comes with an AC
power supply or DC power cord with one of the following plug types.
Barrel plug-type variants: Connect the barrel plug end of the power supply to
the power connector on the unit, and plug the other end into a wall outlet.
nThe barrel plug end of the power supply has a twist-lock connector. Once
you have plugged in the connector, rotate it 90 degrees to secure it in place.
nInternational units come with interchangeable power supply adapters.
© 2017 Digi International Inc.
Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this
document are the property of their respective owners.
Terminal block variants: Remove the pluggable connector from the unit and screw down a proper power source to its terminals.
Next, reconnect the pluggable connector to the unit, following the pin-out diagram below.
5. When the unit is powered-up, the POWER LED illuminates and the unit initiates a series of diagnostic self-tests. During this process one or
more of the other indicators flashes to show that the unit is busy. When the flashing stops, the unit has completed its self-test diagnostic
and is ready to be configured.
Note Position the Digi TransPort WR21 on a flat, level surface or via wall-mount, rackmount, or DIN rail mounting brackets in a location with
adequate ventilation. The unit is designed for indoor use. Do not expose the unit to extreme heat or cold, strong magnetic fields, or liquids.
3Run the Getting Started Wizard
If your PC is configured to automatically get an IP address, it can obtain the IP address from the TransPort WR21. Otherwise, make sure your
PCcan connect to the network 192.168.1.0 (255.255.255.0).
1. Enter 192.168.1.1 into the address bar of the web browser.
2. The first page of the Getting Started Wizard appears. This wizard guides you through initial configuration for your TransPort device.
nTo run the wizard, click Get Started.
nTo manually configure the TransPort device, click Skip Wizard.
Note The default username and password for logging in to the TransPort device are username and password.
4View the TransPort LEDs and startup states
nPOWER LED:
Off: No power
Green:TransPort device is powered
nn SERVICE LED:
Off: No WWAN network connection
Green: Connected to WWAN network
Flashing: WWAN traffic is being transmitted or received
nWWAN LED: Indicates the presence and level of cellular service running on the device.
Off: No cellular service
1 Blink: GPRS mode
2 Blinks: EDGE mode
3 Blinks: UMTS mode
4 Blinks: HSDPA mode
5 Blinks: HSUPA mode
6 Blinks: LTE mode
nSIGNAL LEDs: Indicate the strength of the cellular signal.
3 LEDs: Excellent
2 LEDs: Good
1 LED: Fair
0 LEDs: Poor or no signal
After the Getting Started Wizard completes, the TransPort web interface appears. For additional configuration, use the web interface and refer
to the Digi TransPort User Guide and Application Notes on the Digi website at www.digi.com/support/TransPortWR21.
Otros manuales para TransPort WR21
5
Tabla de contenidos
Otros manuales de Enrutador de red de Digi
Digi
Digi XLR PRO Manual de usuario
Digi
Digi TX54 Manual de usuario
Digi
Digi Connect Series Guía del usuario
Digi
Digi HR4420i Manual de usuario
Digi
Digi IX14 Manual de usuario
Digi
Digi XPress Manual de usuario
Digi
Digi Connect Series Guía del usuario
Digi
Digi EX40 Manual de usuario
Digi
Digi TX40 Manual de usuario
Digi
Digi TX54 Manual de usuario
Digi
Digi TransPort WR11 Manual de usuario
Digi
Digi WR41v1 Manual de usuario
Digi
Digi TransPort WR31 Manual de usuario
Digi
Digi XPressWireless Manual de usuario
Digi
Digi IX20-WAG4 Manual de usuario
Digi
Digi IX20 Manual de usuario
Digi
Digi TransPort Manual de usuario
Digi
Digi TransPort LR54 Manual de usuario
Digi
Digi TransPort WR21 Manual de usuario
Digi
Digi TransPort WR31 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad
LevelOne
LevelOne FBR-1416 Manual de usuario