Digi XTend PKG-R Manual de usuario

XTend PKG-R RF Modem |Quick Start Guide

Requirements

To install the modem and test its range, you need:

•Two XTend RF Modems. The two XTend RF Modems are referred to as Radio1 and Radio2

•Accessories: loopback adapter, RS-232 cable, two RPSMA antennas, two power supplies

•One computer with XCTU

Connect the hardware

1. Set both Radio DIP Switches to RS-232, point-to-point modes. Switches 1 and 5 are ON (up), and the

remaining four switches are OFF (down).

2. Connect the included RS-232 cable to the female DB-9 connector of Radio1 and the male DB-9 connector

of the PC.

3. Attach the serial loopback adapter to the female DB-9 connector of Radio2. The serial loopback adapter

configures Radio2 to function as a repeater by looping data back into the module for retransmission, as

shown.

4. Attach RPSMA antennas to each RF modem.

5. Power Radio1 and Radio2 through their respective power connectors.

WARNING! When operating with 1 Watt power output, transmitting in close proximity of other RF modems can

damage modem front-ends. Observe a minimum separation distance of 0.6 m (2 in) between the RF

modems.

Install software

Download the Legacy XCTU version 5.2.8.6 installer: http://ftp1.digi.com/support/utilities/

40003002_C.exe

When the download is complete, run the executable file and follow the steps in the XCTU Setup Wizard.

Go to https://www.digi.com/products/xbee-rf-solutions/xctu-software/xctu#productsupport and under

General Drivers select the appropriate operating system to download drivers.

Perform a range test

A range test is a simple point to point wireless demonstration that tests the devices' ability to transmit to

and receive from each other. Configure a serial port to communicate with the modem:

1. Launch XCTU: Start > All Programs > Digi > X-CTU.

2. On the PC Settings tab, select the PC serial com that you will use to connect to Radio1 from the list.

3. Select the baud rate that matches the Radio1 I/O interface rate (serial data rate). Use the default values for

the remaining fields.

XTend PKG-R RF Modem |Quick Start Guide

4. Click the Range Test tab.

5. (Optional) Check the box in the RSSI section to enable display of signal strength. The Loop Back option is

automatically selected.

6. Click Start to begin the range test.

7. Move Radio2 (with the loopback adapter) away from Radio1 to determine the maximum range of the

wireless link.

Additional configuration options

Out-of-box, the XTend-PKG-R RF Modem is configured to provide immediate wireless links between

devices. The modem's default configuration supports a wide range of RF communications.

If the RF Modem must be configured to support specific needs of a data system, several programming

options are available.

XTend PKG-R RF Modem |Quick Start Guide

Use the DIP switch

The DIP switch allows you to configure the following RF modem settings.

DIP Switch Settings (applied only when powering on):

Restore modem defaults (DIP switch method)

If the XTend modem is not responding or cannot enter into Command mode, try restoring the modem to

its original default parameter values.

1. Set switches 1 and 2 of the DIP Switch to their ON (up) positions, and the remaining four switches to their

OFF (down) positions.

2. Turn off the power supplying the RF modem, then on again.

Using the DIP switch to configure the modem is one of several ways to configure modem parameters.

Other options include using the XCTU Software Terminal and Modem Configuration tabs, and binary

programming. See the user's guide for more information about these options.

User guide

For more information, see the user guide: https://www.digi.com/resources/documentation/digidocs/

PDFs/90000813.pdf

Tabla de contenidos

Otros manuales de Módem de Digi

Digi

Digi XTP9B-PKC-UA Manual de usuario

Digi

Digi M10 Technical overview and Manual de operación y mantenimiento

Digi

Digi XBee-PRO PKG-U Manual de usuario

Digi

Digi XBee 3 Manual de usuario

Digi

Digi Modem Digi One IA Manual de usuario

Digi

Digi XBee-PRO 900HP Manual de usuario

Digi

Digi XBee3 XB3M1 Manual de usuario

Digi

Digi XBee 3 Cellular LTE-M Manual de usuario

Digi

Digi XBEE2 Manual de usuario

Digi

Digi XBee3 DigiMesh 2.4 Manual de usuario

Digi

Digi XBee Manual de usuario

Digi

Digi XStream -PKG- R Manual de usuario

Digi

Digi XStream-PKG Guía del usuario

Digi

Digi XStream-PKG-E Manual de usuario

Digi

Digi MF710M Manual de usuario

Digi

Digi XBee-PRO XSC RF Modem Manual de usuario

Digi

Digi WAN 3G Manual de usuario

Digi

Digi XLR PRO Manual de usuario

Digi

Digi 9XTend-PKG-U Manual de usuario

Digi

Digi XStream-PKG-U Manual de usuario

Digi

Digi Connect WAN 3G IA Manual de usuario

Digi

Digi XStream-PKG-R RS-232 Manual de usuario

Digi

Digi XLR PRO Manual de usuario

Digi

Digi XBee Cellular 3G Global Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario