DFI LanParty KT400A Manual de usuario

LANPARTY

KT400A

Rev.A+

System Board

User’s Manual

70900310

This publication contains information that is protected by copy-

right. No part of it may be reproduced in any form or by any

means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98,

Windows®98 SE, Windows®ME, Windows®2000, Windows NT®

4.0 and Windows®XP are registered trademarks of Microsoft

Corporation. AMD, AthlonTM XP, AthlonTM and DuronTM are

registered trademarks of Advanced Micro Devices, Inc. VIA is a

registered trademark of VIA Technologies, Inc. Award is a registered

trademark of Award Software, Inc. Other trademarks and registered

trademarks of products appearing in this manual are the properties

of their respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual”.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications.................................................................................

1.2 Package Checklist...........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .......................................................................................

2.2 Installing the CPU in a Socket A...........................................................

2.3 System Memory........................................................................................................

2.4 Jumper Settings for Clearing CMOS Data.................................

2.5 Switch Settings for Selecting the CPU’s Front Side

Bus.............................................................................................................................................

26 Jumper Settings for Serial ATA.................................................................

27 Ports and Connectors........................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features .....................................................

3.1.4 Integrated Peripherals........................................................................

3.1.5 Power Management Setup..........................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Genie BIOS Setting.............................................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.12 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving.............................................................................

3.2 Updating the BIOS.......................................................................................................

Introduction

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface..................................................................

4.2 Drivers, Utilities and Software Applications..................................

4.3 CMedia Audio Sofware Application......................................................

4.4 Installation Notes.........................................................................................................

AppendixA - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function..................................................

Appendix B - System Error Messages

B.1 POST Beep.........................................................................................................................

B.2 Error Messages.............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist...................................................................................

105

107

112

108

114

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIA®KT400A andVT8235CD

Processor

The system board is equipped with Socket-A for PGA processor.

It is also equipped with a switching voltage regulator that auto-

matically detects 1.100V to 1.850V.

• AMD AthlonTM XP 266/333MHz FSB

• AMD AthlonTM 200/266MHz FSB

• AMD DuronTM 200MHz FSB

Important:

To ensure proper boot up and operation of your system, you

must power-off the system then turn off the power supply’s

switch or unplug the AC power cord prior to replacing the CPU.

System Memory

• Supports up to 3GB memory (unbuffered DIMM)

• Uses PC1600 (DDR200), PC2100 (DDR266), PC2700

(DDR333) or PC3200 (DDR400) DDR SDRAM DIMM, 2.5V

type

• Three184-pin DDR SDRAM DIMM sockets

• L2 cache memory

- DuronTM processor: built-in 64KB Level 2 pipelined burst

cache

- AthlonTM XP / AthlonTM processor: built-in 256KB Level 2

pipelined burst cache

Chapter 1 - Introduction

Introduction

Expansion Slots

The system board is equipped with 1 AGP slot and 5 PCI slots.

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending.The AGP slot

supports AGP 8x with up to 2132MB/sec. bandwidth and AGP 4x

with up to 1066MB/sec. bandwidth for 3D graphics applications.

AGP in this system board will deliver faster and better graphics to

your PC.

Onboard Audio Features

• AC’97 2.2 S/PDIF extension compliant codec

• Supports Microsoft®DirectSound/DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• 6-channel audio output

Onboard Dual LAN Features

• Uses VIA VT6103 Phy and Realtek 8101L controllers

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

ATA RAID - Redundant Array of Inexpensive Disk

• RAID 0, 1, 0+1 and 1.5

• Two independent IDE channels support 4 hard disk drives

(UDMA modes 33/66/100/133 or EIDE)

• Supports PIO modes 0/1/2/3/4, DMA modes 0/1/2 and

UDMA modes 0/1/2/3/4/5/6

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

Serial ATA IDE Interface

• Uses Marvell 88i8030 chip

• Supports one SATA (Serial ATA) interface which is compliant

with SATA 1.0 specification (1.5Gbps interface)

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

IEEE 1394a Interface

• Uses VIA VT6306 chip

• Supports three 100/200/400 Mb/sec ports

The VIA VT6306 controller is a complete single chip IEEE 1394a

solution. It is fully compliant with the 1394a OHCI (Open Host

Controller Interface) 1.1 specification. 1394a is a fast external bus

standard that supports data transfer rates of up to 400Mbps. In

addition to its high speed, it also supports isochronous data transfer

which is ideal for video devices that need to transfer high levels of

data in real-time. 1394a supports both Plug-and-Play and hot

plugging allowing devices to be attached or removed from the

system, even with the power on.

S/PDIF

The system board is equipped with the S/PDIF (Sony/Philips Digital

Interface) digital audio interface. S/PDIF is a standard audio file trans-

fer format that transfers digital audio signals to a device without

having to be converted first to an analog format.This prevents the

quality of the audio signal from degrading whenever it is converted

to analog.

Introduction

IrDA Interface

The system board is equipped with an IrDA connector for wire-

less connectivity between your computer and peripheral devices.

USB Ports

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1

supports 12Mb/second bandwidth while USB 2.0 supports 480Mb/

second bandwidth providing a marked improvement in device

transfer speeds between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals..

BIOS

• Award BIOS, Windows®95/98/2000/ME/XP Plug and Play

compatible

• Genie BIOS provides:

- CPU/DRAM overclocking in 1MHz stepping

- CPU/AGP/DRAM/Chipset overvoltage

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 4Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS.The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

Rear Panel I/O Ports (PC 99 color-coded connectors)

• Four USB 2.0/1.1 ports

• Two RJ45 LAN port

• Two NS16C550A-compatible DB-9 serial ports

• One SPP/ECP/EPP DB-25 parallel port

• One mini-DIN-6 PS/2 mouse port

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario