DFI AK70 Manual de usuario

AK70

Rev. A+

System Board

Users Manual

41300007

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior written

permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any express

or implied warranties of merchantability or fitness for any particular

purpose.The user will assume the entire risk of the use or the results

of the use of this document. Further, the manufacturer reserves the

right to revise this publication and make changes to its contents at any

time, without obligation to notify any person or entity of such revisions

or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM ,Windows®95 and Windows®98

are registered trademarks of Microsoft Corporation. AMD AlthlonTM

is a registered trademark of Advanced Micro Devices, Inc. Award is a

registered trademark of Award Software, Inc. Other trademarks and

registered trademarks of products appearing in this manual are the

properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the

receiver.

 Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

2. Shielded interface cables must be used in order to comply

with the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications ....................................................................

1.2 Package Checklist .........................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ................................................................................

2.2 System Memory ...........................................................................................

2.3 Processor Installation .................................................................................

2.4 Jumper Settings for Clearing CMOS Data. ................................

2.5 Ports and Connectors .............................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System ........................................................

3.1.1 Standard CMOS Features .....................................................

3.1.2 Advanced BIOS Features .......................................................

3.1.3 Advanced Chipset Features .................................................

3.1.4 Integrated Peripherals ...............................................................

3.1.5 Power Management Setup ....................................................

3.1.6 PnP/PCI Configurations ...........................................................

3.1.7 PC Health Status .........................................................................

3.1.8 Load Fail-Safe Defaults .............................................................

3.1.9 Load Optimized Defaults ......................................................

3.1.10 Set Supervisor Password .......................................................

3.1.11 Set User Password ....................................................................

3.1.12 Save & Exit Setup .......................................................................

3.1.13 Exit Without Saving ....................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface ........................................................

4.2 Drivers ...............................................................................................................

Appendix A - System Error Messages

A.1 POST Beep ....................................................................................................

A.2 Error Messages .............................................................................................

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist .....................................................................

1.1 Features and Specifications

1.1.1 Features

Chipset

 AMD-750

AGP chipset

Processor

The system board is equipped with a single 242-pin Slot A

mechanical connector supporting all AMD Athlon processor

modules. The system board is also equipped with a switching

voltage regulator that supports 1.3V to 2.05V core voltage for

various processors.

 AMD Althlon processor module - 500MHz and faster

 200MHz system interface speed (DDR - Double Data Rate)

 Auto-detect processor voltage

 Clock multiplier 5.0 to 10.0

 ECC protection on system and cache interfaces

Cache Memory

 Processor built-in 128-Kbyte L1 cache

 Processor built-on 512-Kbyte L2 cache

System Memory

 16MB to 768MB memory using unbuffered DIMMs

 Three 168-pin 3.3V DIMM sockets

 Supports PC-100 SDRAM memory

 ECC supported (uses x72 PC SDRAM DIMM)

Chapter 1 - Introduction

DIMMs

2MBx64/x72

4MBx64/x72

8MBx64/x72

16MBx64/x72

32MBx64/x72

Memory Size

16MB

32MB

64MB

128MB

256MB

Introduction

Expansion Slots

The system board is equipped with 1 dedicated AGP slot and 5

dedicated PCI slots. All PCI slots are bus masters. AGP is an

interface designed to support high performance 3D graphics cards.

It utilizes a dedicated pipeline to access system memory for

texturing, z-buffering and alpha blending; delivering up to 533MB/

sec. bandwidth for 3D graphics applications.

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in

the DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

ATX Double Deck Ports

 2 USB ports

 2 DB-9 serial ports

 1 DB-25 parallel port

 1 min-DIN-6 PS/2 mouse port

 1 min-DIN-6 PS/2 keyboard port

Connectors

 1 connector for IrDA interface

 1 connector for 2 additional external USB ports

 2 IDE connectors

 1 floppy connector

 1 20-pin ATX power supply connector

 1 Wake-On-Ring connector

 1 Wake-On-LAN connector

 1 chassis fan connector, 2 CPU fan connectors for CPU Fan1

and CPU Fan2

Introduction

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

Supports ATA/33 or ATA/66 hard drives

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for

wireless connectivity between your computer and peripheral

devices. It supports infrared peripheral devices that meet the

ASKIR or HPSIR standard.

USB Ports

The system board supports 4 USB ports. USB allows data

exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

 AMD/Award BIOS with ACPI

 Flash EPROM for easy BIOS upgrades

 Supports DMI 2.0 function

 Auto-detect and report system health status

 2 Mbit flash memory

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors processor/system temperature and processor

overheat alarm

 Monitors 3.3V/±5V/±12V/VCORE voltages and failure alarm

 Monitors processor/chassis fan speed and failure alarm

 Read back capability that displays accurate temperature, voltage

and fan speed

Introduction

1.1.3 Intelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the

system enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the BIOS setup, this switch will allow

the system to enter the Soft-Off or Suspend mode.

Wake-On-Ring

This feature allows the system that is in the Suspend mode or Soft

Power Off mode to wake-up/power-on to respond to calls

coming through an internal or external modem. Refer to Wake-

On-Ring Connector in chapter 2 for more information.

Wake-On-LAN Ready

The Wake-On-LAN function allows the network to remotely wake

up a Soft Power Down (Soft-Off) PC. Your LAN card must

support the remote wakeup function.

Important:

The 5VSB power source of your power supply must support

≥

720mA (minimum).

RTC Timer to Power-on the System

The RTC installed on the system board allows your system to

automatically power-on on the set date and time.

ACPI

The system board is designed to meet the ACPI (Advanced

Configuration and Power Interface) specification. ACPI has energy

saving features that enables PCs to implement Power Management

and Plug-and-Play with operating systems that support OS Direct

Power Management.

Introduction

Virus Protection

Most viruses today destroy data stored in hard drives. The system

board is designed to protect the boot sector and partition table

of your hard disk drive.

1.2 Package Checklist

The system board package contains the following items:

þThe system board

þA users manual

þOne IDE cable for ATA/66 or ATA/33 IDE drives

þOne 34-pin floppy disk drive cable

þOne CD

¨One card-edge bracket with two USB ports (optional)

If any of these items are missing or damaged, please contact your

dealer or sales representative for assistance.

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario