Detecto 450 Manual de usuario

8525-M058-O1 Rev F 450 Series Owner’s Manual

450 Series

Mechanical Baby Scale

Owner’s Manual

8525-M058-O1 Rev F 450 Series Owner’s Manual

INTRODUCTION

The Detecto 450 Series Mechanical Baby Scale is ideal for use in health clinics and medical

practices for height and weight measurement of pediatric patients. The scale is durable, having

a sturdy enameled steel scale base, a built-in measuring tape (up to 21 in / 53 cm) to allow the

healthcare professional to measure both weight and height simultaneously, and an easy-to-

clean polystyrene tray that cradles babies securely.

This manual is provided to guide you through the assembly and operation of your scale.

Please read it thoroughly before attempting to assemble or operate your scale and keep it

available for future reference.

This manual is for use with the following Mechanical Baby Scale models:

450 451

pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to the

use of the information contained herein.

DISCLAIMER

While every precaution has been taken in the preparation of this manual, the Seller assumes

no responsibility for errors or omissions. Neither is any liability assumed for damages resulting

from the use of the information contained herein. All instructions and diagrams have been

checked for accuracy and ease of application; however, success and safety in working with

tools depend to a great extent upon individual accuracy, skill, and caution. For this reason, the

Seller is not able to guarantee the result of any procedure contained herein. Nor can they

assume responsibility for any damage to property or injury to persons occasioned from the

procedures. Persons engaging in the procedures do so entirely at their own risk.

8525-M058-O1 Rev F 450 Series Owner’s Manual

UNPACKING

Remove the scale base, the column with weigh beam headpiece, baby tray, and hardware kit

from the shipping carton. After removing from the carton, check for any damage that may have

occurred during shipment. Note that the purchaser is responsible for filing all claims for any

damages or loss incurred during transit. Keep and use the original carton and packing material

for return shipment if it should become necessary.

SPECIFICATIONS

Models: 450 451

Capacity: 130 lb x 1 oz 65 kg x 20 g

Measuring Tape: 0 to 21 in x 0.25 in (0 to 53 cm x 0.1 cm)

Platform Dimensions: 14.75 in x 10.75 in (37.5 cm x 27.3 cm)

Tray Dimensions: 22 in W x 14.75 in D x 4.5 in H (56 cm W x 37 cm D x 11 cm H)

Column

Small Poise

Weigh Beam

Scale Base

Baby Tray

with built-in

Measuring

Tape

Large Poise

8525-M058-O1 Rev F 450 Series Owner’s Manual

SCALE ASSEMBLY

The Detecto 450 Series Mechanical Baby Scale comes partially assembled. The following

components require assembly:

Column

Draft Rod

Baby Tray

Tools required:

Phillips head screwdriver

Wrench (included)

1. Set the scale base on a table or other assembly area free from traffic and obstructions.

2. Remove the cable tie that secures the draft rod during transit (shown in Figure 1).

Figure 1. - Remove cable tie securing draft rod in column

3. Insert the column onto the scale base (shown in Figure 2), ensuring that the DETECTO

logo on the weight beam faces the scale base.

Figure 2. - Insert column onto scale base

Draft Rod

Cable Tie

Column

Scale Base

8525-M058-O1 Rev F 450 Series Owner’s Manual

SCALE ASSEMBLY, CONT.

4. Using a Phillips screwdriver, install the eight screws and washers to secure the column to

the scale base as shown in Figure 3.

Figure 3. - Install eight screws and washers to secure the column to scale base

5. Lay the scale on a table. Remove and discard the shipping tie-wrap wires on the underside

of the scale base as shown in Figure 4.

Figure 4. - Lay scale on a table to access the bottom of scale base

8525-M058-O1 Rev F 450 Series Owner’s Manual

SCALE ASSEMBLY, CONT.

6. Insert the wrench (included) into the small hole in front of the draft rod and pull the draft rod

hook with the wrench to connect it to the long lever as shown in Figure 5. The draft rod is

located inside the scale column. Once the column is attached to the scale base, the draft

rod must be attached to the long lever.

Figure 5. - Connect draft rod hook to the long lever

7. Push the long lever forward and hook the draft rod’s hook onto the long lever pivot.

IMPORTANT! During shipping, a plug is installed to ensure that the shelf lever

assembly stays aligned. However, the linkage may still come out of alignment.

Remove the plug and then visually ensure that the shelf lever assembly linkage is

centered and properly aligned. The linkage must be free-floating for the scale to

weigh properly. If the scale is slightly tipped to one side, the linkage can be seen by

looking up underneath the weigh beam headpiece.

Figure 6. - View of linkage underneath weigh beam headpiece

8. Place the scale gently back on the floor.

Draft Rod Hook

Long

Lever

Insert

wrench

here

Remove

shipping

linkage

alignment

plug

Shelf lever

assembly linkag

must be properly

aligned in order

to weigh

8525-M058-O1 Rev F 450 Series Owner’s Manual

SCALE ASSEMBLY, CONT.

9. Attach baby tray to scale platform using the two (2) flat head screws provided. Do not over-

tighten screws.

Figure 7 - View showing attachment of baby tray to scale platform base.

Attach baby tray

with (2) provided

flat head screws.

8525-M058-O1 Rev F 450 Series Owner’s Manual

BALANCING THE SCALE

After assembly, the scale must be balanced before using it.

1. Ensure the scale is sitting on a level surface, and slide both the small and large poise to

zero (far-left position on the weigh beam).

2. Gently hold the beam pointer with your finger so it is centered within the trig loop area.

Release the beam pointer and let it rise freely up or down.

3. If the beam pointer doesn’t remain centered, turn the balance screw (shown in Figure 8) to

the right or left using a flathead screwdriver until the beam pointer remains centered within

the trig loop.

Figure 8 - View showing components for balancing scale prior to normal operation.

Small Poise Large Poise

Weigh Beam

lance

Screw Beam Pointer

Trig L

oop

8525-M058-O1 Rev F 450 Series Owner’s Manual

OPERATING THE SCALE

The following steps will guide you through the operation of your 450 Series, Weigh Beam

Neonatal Scale. Refer to Figure 9 below when performing the steps.

1. Move both poise to the Zero position. Be sure the Beam Pointer is in the center of the

opening in the Trig Loop.

2. Slide the Large Poise to the approximate weight. For example, if the patient weighs

approximately 20 pounds, slide the Large Poise to 10 pounds.

3. Place the patient on the scale, and then slide the Small Poise to 5 pounds.

4. Continue sliding the Small Poise until the Beam Pointer is centered in the Trig Loop

opening.

5. Read the Small Poise at the pointer and add to the 10 pounds from the Large Poise. For

example, if the pointer is at 8 pounds, the patient weighs 18 pounds.

Figure 9 - View showing the procedure for weighing operation.

CAUTION!

Do not leave the baby unattended in the baby tray.

Failure to maintain continual control of the baby can

result in serious injuries should the baby fall from the

baby tray.

Large Poise

Small Poise Beam Pointer

centered in

Trig Loop

Trig L

oop

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Detecto

Detecto

Detecto ProDoc PD100 Manual de usuario

Detecto

Detecto 6027 Manual de usuario

Detecto

Detecto PS-4 Manual de usuario

Detecto

Detecto 7550 Manual de usuario

Detecto

Detecto DR150 Manual de usuario

Detecto

Detecto P220 Manual de usuario

Detecto

Detecto 6027 Manual de usuario

Detecto

Detecto PS-11 Manual de usuario

Detecto

Detecto 6855KGEU Manual de usuario

Detecto

Detecto 6475 Manual de usuario

Detecto

Detecto 6475 Manual de usuario

Detecto

Detecto D161 Manual de usuario

Detecto

Detecto IB400 Manual de usuario

Detecto

Detecto GP-400-758C Guía de referencia

Detecto

Detecto 6875 Manual de usuario

Detecto

Detecto AP-10 Guía de referencia

Detecto

Detecto ProDoc PD100 Manual de usuario

Detecto

Detecto 8463 Manual de usuario

Detecto

Detecto VET550 Manual de usuario

Detecto

Detecto PS-7 Manual de usuario

Detecto

Detecto WPB Series Manual de usuario

Detecto

Detecto SlimPRO Manual de usuario

Detecto

Detecto CS Series CS-30 Manual de usuario

Detecto

Detecto 6745 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario