Dell MC SD-WAN Edge 3400 Advanced Manual de usuario

Dell EMC SD-WAN Edge 3400 Advanced

Activation Guide

H18671.1

February 2021

Introduction

The Dell EMC SD-WAN Edge is purpose-built for next-generation WAN access deployments. The Dell EMC SD-WAN Edge

3000 series is a performance-designed solution integrated with industry-leading VMware SD-WAN software; and also offers

centralized orchestration and available gateways. It offers hosted virtualized network functionality, with applicability for the SP

Edge and Enterprise Branch. The SD-WAN Edge 3000 series is 1 RU sized, and uses the latest Intel®Xeon®D-2100 x86-based

processor, which is optimized for high-performance networking. Dell EMC is the first to market with Xeon-D for SD-WAN.

●VMware SD-WAN Edge—a hardware device with VMware software preinstalled.

●VMware SD-WAN Gateway—VMware SD-WAN networks consists of gateways deployed at top tier network points-of-

presence and cloud data centers around the world. SD-WAN Gateway also provides SD-WAN services to the doorstep of

SaaS, IaaS, cloud network services, and access to private backbones.

●VMware SD-WAN Orchestrator—SD-WAN Orchestrator provides centralized enterprise-wide configuration, real-time

monitoring, and orchestrates the data flow into and through the SD-WAN overlay network.

NOTE: For software information, see the VMware documentation at https://sdwan.vmware.com/.

NOTE: After unpacking the Dell EMC SD-WAN Edge 3400 system, inspect the device and immediately report any damage

to your Dell Technologies sales representative.

Dell EMC SD-WAN Edge 3400 installation considerations

It is important to work with your company IT or security teams to determine the network infrastructure for the site where the

SD-WAN Edge 3400 system is to be installed. If the SD-WAN Edge 680 system is to be connected behind a firewall, these

settings must be in place for the product to function properly.

Table 1. Mandatory ports

Protocol Port Description

VeloCloud Multipath Protocol (VCMP) UDP/2426 VMware SD-WAN tunnel protocol

HTTPS TCP/443 Needed for SD-WAN Orchestrator communication

NTP UDP/123 Needed for time sync (security)

DNS UDP/53 Needed for translation of SD-WAN Orchestrator URLs,

among other use cases

If the SD-WAN Edge 3400 system is connected behind a NAT, UDP hole punching is used to open the ports for inbound VCMP

traffic. To enable UDP hole punching, click Configure > Edge > Device > WAN Settings to edit the relevant overlay.

Table 2. Conditional ports

Protocol Port Description

IKE UDP/500 Used by SD-WAN Edge 3400 system to form IPSec tunnels with certain CSS solutions

ESP IP/50 Used by SD-WAN Edge 3400 system to form IPSec tunnels with certain CSS solutions

NAT traversal UDP/4500 Needed to pass IKE and ESP over NAT

NOTE: If you plan to use SFP/SFP+ modules, contact your Dell Technologies Sales Representative to ensure compatibility.

Dell EMC SD-WAN Edge 3400 standard configuration

Follow the steps below to install the SD-WAN Edge 3400 system in the standard configuration.

Step 1. Connect the power

Connect the power adapter to an AC power outlet. Connect the other end of the power adapter to the power port on the

SD-WAN Edge 3400 system. When the SD-WAN Edge 3400 system powers ON, verify that the status LED on the front of the

SD-WAN Edge 3400 system is illuminated.

Step 2. Connect to the Internet

Connect an Ethernet cable to an available Internet connection, and then connect the cable to one of the four ports labeled GE3,

GE4, GE5, GE6, or any SFP+ port.

NOTE: The SD-WAN Edge 3400 system is configured by default to acquire a DHCP IP address from the ISP on the WAN

(uplink). When the WAN connection is fully operational, the LED on the front of the SD-WAN Edge 3400 is green. To use a

static IP address, see the Setting up a static IP address section.

Step 3. Follow email instructions

NOTE: If you received an email from your IT administrator, follow the instructions in the email to complete the activation

of the SD-WAN Edge 3400. If you did not receive an email, request the setup instructions from your IT administrator or

contact your Dell Technologies sales representative.

Step 4. Connect local devices

Connect the local devices such as desktops, phones, or switches to any of the LAN ports.

Dell EMC SD-WAN Edge 3400 advanced configuration

The following sections describe the optional advanced configurations that are supported and listed within the Activation Quick

Start Guide that is included with the SD-WAN Edge 3400 system.

Set up a static IP address

1. Connect the SD-WAN Edge 3400 system through Ethernet or Wi-Fi and obtain a DHCP IP address.

NOTE: In this example, GE1 is used.

2. Open a web browser and type http://192.168.2.1 in the address bar.

3. Click the Details button located below the image of the SD-WAN Edge 3400.

4. In the Edge Overview section of the screen, click the Connected button to view the connected interfaces.

Figure 1. Connected interfaces

5. Click the name of the interface you want to set with a static IP address.

NOTE: In this example, the WAN interface is connected to GE5, shown in red.

6. Under Configuration > Addressing, select the Static radio button, then type the IP Address, Subnet Mask, and Gateways

in the appropriate text boxes.

Figure 2. Static IP address assignment

7. Click Save (upper-right of the Configuration screen) to apply the settings.

8. When prompted, type the default username admin and the default password admin and click OK. The SD-WAN Edge 3400

attempts to reach the SD-WAN Gateway address, and the icon will turn green when successful.

NOTE: Based on your service provider, a VLAN ID may be required.

Figure 3. GE5 shown with active WAN connectivity

NOTE: SD-WAN Edge activation retains the static IP address settings when the activation profile has the corresponding

port configured as a routed port.

Set up PPPoE

To configure PPPoE, perform the following steps:

1. Connect through Ethernet or Wi-Fi and obtain a DHCP IP address from the SD-WAN Edge 3400.

NOTE: In this example, GE1 is used.

2. Open a web browser and type http://192.168.2.1 in the address bar.

3. Click the Details button located below the image of the SD-WAN Edge 3400.

4. Click the name of the interface you want to configure for PPPoE, for example, GE3.

5. Under Configuration > Addressing, select the Static radio button, and enter the Username and Password.

Figure 4. PPPoE configuration

6. Click Save (upper-right of the Configuration screen) to apply the settings.

7. When prompted, type in the default username admin and the default password admin and click OK.

NOTE: VMware activation retains the PPPoE address settings when the activation profile has the corresponding port

configured as a routed port.

Install and configure an SFP module as WAN interface

1. Verify that the SFP module you want to install is compatible with the device.

NOTE: For information about compatibility, contact your Dell Technologies Sales Representative.

2. Insert the SFP module in any SFP port.

Figure 5. SFP ports

NOTE: If the link lights do not illuminate, use the UI to reboot the SD-WAN Edge 3400 system.

3. When the module is ready, it shows as Available in the WAN interface with the associated DHCP address.

NOTE: Follow the procedure above to configure the static IP address if needed. If problems persist, see VMware KB article

KB59582.

Dell EMC SD-WAN Edge 3800 activation troubleshooting

Internet status not available

1. Verify physical cabling.

2. Ensure that the SD-WAN Edge 3800 MAC address is learned on the correct port or VLAN.

3. For static IP, verify that the IP address or mask and gateway are properly configured.

4. Verify that the VMware SD-WAN Gateway is reachable.

Verify the SD-WAN Edge 3800 MAC address is listed on the gateway

You can verify that the SD-WAN Edge 3800 MAC is seen on the gateway to confirm Layer 2 connectivity.

Figure 6. MAC Address listing

NOTE: Alternatively, the MAC address can be found printed on a sticker on the bottom of the SD-WAN Edge 3800.

The following figure shows results of arp- n from a device on the same network segment.

Figure 7. arp -n command results

NOTE: The MAC address match-up for the SD-WAN Edge 3800 device public WAN on GE3 is shown in the figure above.

Verify that the gateway IP address is reachable

1. Remove the configured WAN connection from the SD-WAN Edge 3800 and connect directly to a system.

2. Configure the system with an identical network configuration.

3. Ping the gateway address.

Figure 8. Ping gateway address

If the ping fails and the gateway is a firewall, ICMP may be blocked, in which case the Internet status will remain unconnected.

Wait for the retry to timeout and click Activate. Also, ensure that the SD-WAN Orchestrator IP address is reachable using

TCP/443.

NOTE: See VMware KB article KB2341023 for details.

Verify configuration string values

When the SD-WAN Edge 3800 is updated before activation (for example, setting a static IP address), a configuration string is

appended to the activation URL. This string is Base64 and is used to specify the static IP address during activation.

http://192.168.2.1/?activation_key=1X1X-1X1X-1X1X-1X1X1&custom_vco=vco109-

usca1.velocloud.net&configuration=W3siaW50ZXJmYWNlIjoiR0UzIiwicHJvdG8iOiJzdGF0aWMiLCJpcCI

6IjE0My4xNjYuODEuMjIiLCJnYXRld2F5IjoiMTQzLjE2Ni44MS4xIiwibmV0bWFzayI6IjI1NS4yNTUuMjU1LjAi

fV0

The configuration string can be decoded to verify that the profile is configured accurately. Using the above value, the correct IP

address is verified.

[{"interface":"GE5","proto":"static","ip":"143.166.81.29","gateway":"143.166.81.1","netma

sk":"255.255.255.0"}]

VMware SD-WAN Orchestrator is unavailable

If you receive the error that the SD-WAN Orchestrator is not reachable, follow these steps:

1. Change the SD-WAN Orchestrator FQDN to an IP address. You can use the nslookup command to verify the IP address of

the SD-WAN Orchestrator address listed in the activation email.

Figure 9. Change SD-WAN Orchestrator FQDN to IP address

2. Check the ignore certificates with the SD-WAN Orchestrator IP address.

3. Verify that the next-hop device such as a firewall, is not applying an outbound filter to the SD-WAN Orchestrator IP address

for TCP/443.

4. Check the firewall logs for any blocked traffic that matches the SD-WAN Orchestrator IP address.

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

Tabla de contenidos

Otros manuales de Hardware de red de Dell

Dell

Dell PowerProtect DM5500 Manual de usuario

Dell

Dell Z9000 Manual de instrucciones

Dell

Dell OptiPlex Small Form Factor 7010 Manual de usuario

Dell

Dell Secure Mobile Access 6200 Manual de usuario

Dell

Dell PowerEdge M1000e Manual de usuario

Dell

Dell 53-1002116-01 Manual de servicio

Dell

Dell DD6300 Manual de usuario

Dell

Dell SonicWALL NSA E6500 Manual de usuario

Dell

Dell TrueMobile 2300 Manual de usuario

Dell

Dell SonicWALL NSA E8510 Manual de usuario

Dell

Dell PowerConnect W-Airwave Manual de usuario

Dell

Dell PowerVault 110T DLT VS80 Manual de usuario

Dell

Dell PowerEdge 1-U Keyboard Tray Manual de usuario

Dell

Dell PowerFlex R750 Manual de usuario

Dell

Dell EMC VxRail P470 Manual de usuario

Dell

Dell CMC-PD01 Manual de usuario

Dell

Dell PowerProtect Data Manager Appliance 5.13.0.0 Manual de usuario

Dell

Dell VEP4600 Guía del usuario

Dell

Dell SonicPoint-N Dual Radio Manual de usuario

Dell

Dell XC720xd Manual de usuario

Dell

Dell 5821E Manual de usuario

Dell

Dell XC430 Manual de usuario

Dell

Dell EMC NX3240 Instrucciones de uso

Dell

Dell PowerVault NX1950 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario