Dell Z9000 Manual de instrucciones

Installing the Z9000 System

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not

followed.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, Dell Precision™, OptiPlex™, Latitude™, PowerEdge™, PowerVault™,

PowerConnect™, OpenManage™, EqualLogic™, KACE™, FlexAddress™ and Vostro™ are trademarks of Dell Inc. Intel®, Pentium®,

Xeon®, Core™ and Celeron®are registered trademarks of Intel Corporation in the U.S. and other countries. AMD®is a registered trademark

and AMD Opteron™, AMD Phenom™, and AMD Sempron™ are trademarks of Advanced Micro Devices, Inc. Microsoft®, Windows®,

Windows Server®, MS-DOS®and Windows Vista®are either trademarks or registered trademarks of Microsoft Corporation in the United

Statesand/orothercountries.RedHatEnterpriseLinux®andEnterpriseLinux®areregisteredtrademarksofRedHat,Inc.intheUnitedStates

and/or other countries. Novell®is a registered trademark and SUSE ™ is a trademark of Novell Inc. in the United States and other countries.

Oracle®isaregisteredtrademarkofOracleCorporation and/or its affiliates.Citrix®, Xen®, XenServer®and XenMotion®areeither registered

trademarks or trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®, Virtual SMP®, vMotion®, vCenter®,

and vSphere®are registered trademarks or trademarks of VMWare, Inc. in the United States or other countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

November 2011 P/N 101-00393-03

Contents | 3

Contents

1 Preface

About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Information symbols and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 The Z9000 System

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Orderable Z9000 components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

System status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

LED displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Site Preparations

Site selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cabinet placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Rack mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fans and airflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Storing components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4 Install the Z9000

Install the Z9000 chassis in a rack or cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Attach mounting brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Install chassis into rack or cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Attach ground cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Install the QSFP+ optics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Remove the QSFP+ optics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Splitting QSFP ports to SFP+ ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Install the Solid Date Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Supply power and power up the system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Power up sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Hot-swap units in a stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5 Power Supplies

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4| Contents

www.dell.com | support.dell.com

Install a power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Install a new AC power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Install a new DC power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replace a power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Replace an AC power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Replace a DC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6 Fans

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Install a fan module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Replace a fan module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

7 Access ports

Access the RJ-45 console port (RS-232) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Access the RJ-45 console port with a DB-9 adapter . . . . . . . . . . . . . . . . . . . . . 34

Access the USB-B console port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Access the Solid State Drive (SSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Install an SSD.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

View files on the SSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Copy files to and from the SSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Remove files from the SSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

8 Z9000 Specifications

Chassis Physical Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Environmental Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

AC Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

DC Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

IEEE Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Agency Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9 Technical Support

The iSupport website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Accessing iSupport services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Contacting the Technical Assistance Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Requesting a hardware replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Preface | 5

Preface

About this Guide

This guide provides site preparation recommendations, step-by-step procedures for rack mounting and

desk mounting, inserting optional modules, and connecting to a power source.

After you have completed the hardware installation and power-up of the Z9000, refer to the FTOS

Configuration Guide for the Z9000 for software configuration information and the FTOS Command

Reference for the Z9000 for Command Line Interface (CLI) information.

NOTE: The Z9000 requires minimum FTOS version 8.3.11.0.

CAUTION: Wear grounding wrist straps when handling this equipment to avoid ESD damage.

WARNING:

WARNING: The installation of this equipment shall be performed by trained and qualified personnel only. Read this

guide before installing and powering up this equipment. This equipment contains two power cords. Disconnect

both power cords before servicing.

WARNING: This equipment contains optical transceivers, which comply with the limits of Class 1 laser radiation.

WARNING: Visible and invisible laser radiation may be emitted from the aperture of the optical transceiver ports when

no cable is connected. Avoid exposure to laser radiation and do not stare into open apertures

Information symbols and warnings

The following graphic symbols are used in this document to bring attention to hazards that exist when

handling the Z9000 and its components. Please read these alerts and heed their warnings and cautions.

Table 1-1

describes symbols contained in this guide.

Table 1-1. Information Symbols

Symbol Warning Description

Danger This symbol warns that improper handling and installation could result in bodily injury.

Before you begin work on this equipment, be aware of hazards involving electrical circuitry,

networking environments, and instigate accident prevention procedures.

Caution This symbol informs you that improper handling and installation could result in equipment

damage or loss of data.

Warning This symbol informs you that improper handling may reduce your component or system

performance.

6| Preface

www.dell.com | support.dell.com

Related publications

For more information about the Z9000, refer to the following documents:

• FTOS Configuration Guide for the Z9000 system

• FTOS Command Reference for the Z9000 system

•FTOS Release Not

for the Z9000 system

NOTE: For the most recent documentation and software, please visit iSupport (registration for access to some

sections is required):

https://www.force10networks.com/CSPortal20/Main/SupportMain.aspx

Note This symbol informs you of important operational information.

ESD Warning This symbol identifies that Electrostatic precautions should be taken when handling the

device.

Table 1-1. Information Symbols

Symbol Warning Description

The Z9000 System | 7

The Z9000 System

Introduction

The Dell Force10 Networks’ Z9000 platform is a next generation switch/router product designed to meet

the requirements for distributed Data Center cores. It is a 2-rack unit (RU) chassis that supports 32 ports

of 40GE QSFP+ or 128 ports of 10GE SFP+ (with breakout cables). The Z9000 includes an RS-232

console port and a management port for system access. As shown in

Figure 2-1

, the Z9000’s I/O (Input/

Output) side contains the 32 40G QSFP+ auto-sensing ports, and management ports. The Z9000’s PSU

(Power Supply Unit) side (

Figure 2-2

) contains the Power Supply Units and fan modules.

Figure 2-1. The Z9000 I/O side view

Figure 2-2. The Z9000 PSU side view

40G/4x10G

QSFP+ ports

RJ-45/RS-232

Console Port

Primary Management

(Ethernet) Port

USB-A Port

USB-B Port

Stacking

LEDs

Solid State Digital

(SSD) Drive Slot

Grounding

screw

Power Supply (PSU0)

Power Supply (PSU1) Fan Modules

(0-3)

8| The Z9000 System

www.dell.com | support.dell.com

Orderable Z9000 components

The Z9000 can be ordered in several different configurations. Optional modules and optics are ordered

separately.

To successfully install the Z9000, ensure that you have the following:

• Z9000 chassis

• Optics (must be ordered separately, they do NOT come with the base system)

• At least one grounded power source per chassis

• Cable to connect the power source to the chassis (included)

Table 2-1. Supported Hardware Components

Hardware Catalog Number

32-port 40G QSFP+ ports, 1 AC power supply, 1 fan subsystem (airflow from I/O side to

power supply side) Z9000-AC

32-port 40G QSFP+ ports, 1 AC power supply, 1 fan subsystem (airflow from power supply

side to I/O side) Z9000-AC-R

32-port 40G QSFP+ ports, 1 DC power supply, 1 fan subsystem (airflow from I/O side to

power supply side) Z9000-DC

32-port 40G QSFP+ ports, 1 DC power supply, 1 fan subsystem (airflow from power supply

side to I/O side) Z9000-DC-R

Z9000 Series – Fan with airflow from I/O side to PSU side Z9000-FAN

Z9000 Series – Fan with airflow from PSU side to I/O side Z9000-FAN-R

Z9000 Series – AC Power supply with airflow from I/O side to PSU side Z9000-PWR-AC

Z9000 Series – AC Power supply with airflow from PSU side to I/O side Z9000-PWR-AC-R

Z9000 Series – DC Power supply with airflow from I/O side to PSU side Z9000-PWR-DC

Z9000 Series – DC Power supply with airflow from PSU side to I/O side Z9000-PWR-DC-R

Z9000 Series – Solid State Drive (SSD) Z9000-SSD

Table 2-2. Supported optics and cables

Optic Size Optic Type Reach (Meters) Catalog Number

40 Gig

QSFP+ short reach optics 100 M (with OM3 fiber)

150 M (with OM4 fiber) GP-QSFP-40GE-1SR

QSFP+ long reach optics GP-QSFP-40GE-1LR

Active Fiber Direct attach cable 10 M

50 M CBL-QSFP-40GE-10M

CBL-QSFP-40GE-50M

Passive Copper Direct attach cable 1 M

5M CBL-QSFP-40GE-PASS-1M

CBL-QSFP-40GE-PASS-5M

QSFP+

Breakout

Cable

40GE QSFP+ to 4 SFP+ optical

breakout cable (optics not included) 5 M CBL-QSFP-4x10GSFP-5M

40GE QSFP+ to 4 SFP+ passive copper

breakout cable (optics not included) 5 M CBL-QSFP-4x10GSFP-PASS-5M

The Z9000 System | 9

• Mounting brackets for rack installation (included)

• Screws for rack installation (included)

• #1#2 Phillips screwdrivers (not supplied)

• Ground cable (not supplied)

• Ground cable screws (not included)

• USB cable (included)

• Copper/fiber cables

Other optional components are:

• Solid State Drive (included)

• Spare Power Supply Unit

• Spare Fan module

• Spare optics

• Breakout cable

Features

The Z9000 offers the following:

• Z9000 CPU and switch processor

• Hot swappable redundant power supplies

• 19-inch rack-mountable

• Standard 2U chassis height

• Up to 128K MAC address entries supported with hardware assisted aging

• Supports 12K jumbo frames

Ports

• External Serial RS-232 port (RJ45 type)

• Remote management port

• 32-port 40G QSFP+ ports

• USB-A port

• USB-B port

• Solid State Digital (SSD) drive

10 | The Z9000 System

www.dell.com | support.dell.com

System status

Z9000 status information is viewed in several ways, including LEDs and boot menu options. Status

information is also seen through the CLI show commands and with SNMP traps. For details on those

options, see the FTOS Command Reference for the Z9000 and the FTOS Configuration Guide for the

Z9000.

LED displays

As shown in figure below, the Z9000 includes LED displays on the I/O side of the chassis. When the

Z9000 powers up, or reloads, the PSU LED is solid yellow.

The system LEDs are:

• System status (SYS)

• Power status (PSU)

• Alarm status (ALM)

• System locator beacon (LOC)

• System Reset (Reset)

Table 2-3. System LED displays

Label LED Color/Display Description

System status (SYS)

Located on I/O panel

Off

Green solid

Amber solid

No power

Normal operation

Error during boot-up

Power status (PSU0, PSU1)

Located on I/O panel

Green solid

Amber solid

Normal operation

Power supply missing or failed

Alarm status (ALM)

Located on I/O panel

Off

Amber solid

Red solid

No alarm

Minor alarm

Critical alarm

System locator (LOC)

Located on I/O panel

Off

Blue solid

No activity

System beacon/locator

SYS

ALM

PSU0

PSU1

LOC

Reset

Otros manuales para Z9000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Dell

Dell

Dell EMC NX430 System Manual de usuario

Dell

Dell CX4 Series Manual de usuario

Dell

Dell PowerFlex R750 Manual de usuario

Dell

Dell XC720xd Manual de usuario

Dell

Dell PowerEdge FC830 Manual de usuario

Dell

Dell SonicWALL NSA E6500 Manual de usuario

Dell

Dell PowerVault 124T Manual de usuario

Dell

Dell SonicWALL SuperMassive 9600 Manual de usuario

Dell

Dell AX150 Guía de referencia

Dell

Dell DD6300 Manual de usuario

Dell

Dell FS7500 Manual

Dell

Dell XC430 Manual de usuario

Dell

Dell SonicWALL NSA 5600 Manual de usuario

Dell

Dell PowerEdge 1-U Keyboard Tray Manual de usuario

Dell

Dell PowerVault 735N Manual de usuario

Dell

Dell PowerVault TL4000 Manual de usuario

Dell

Dell PowerEdge M1000e Manual de usuario

Dell

Dell PowerProtect Data Manager Appliance 5.13.0.0 Manual de usuario

Dell

Dell PowerConnect W-620 Manual de usuario

Dell

Dell EMC VxRail P470 Manual de usuario

Dell

Dell E665 Manual

Dell

Dell P570 Manual de usuario

Dell

Dell SonicWall SRA 4200/1200 Manual de usuario

Dell

Dell SonicPoint-N Dual Radio Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario