Dell Inspiron 6000 Manual de usuario

DellInspiron™6000ServiceManual

Notes, Notices, and Cautions

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see the Dell Inspiron Help file. To access the help file, click the Start button, click Help and Support, click

User and System guides, click User's guides, and click Dell Inspiron Help.

If you purchased a Dell n Series computer, any references in this document to Microsoft®Windows®operating systems are not applicable.

Information in this document is subject to change without notice.

©2004DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Inc.; Intel is a registered trademarks of Intel Corporation; Microsoft and Windows are

registered trademarks of Microsoft Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Model PP12L

December 2004 Rev. A00

Before You Begin

System Components

Internal Card With Bluetooth®Wireless Technology

Hard Drive

Optical Drive

Memory Module and Modem

Hinge Cover

Keyboard

Coin-Cell Battery

Mini PCI Card

Display Assembly and Display Latch

Palm Rest

Video Card/Thermal-Cooling Assembly

MCH Heat Sink

Fan

Microprocessor Thermal-Cooling Assembly

Microprocessor Module

System Board

Speakers

Flashing the BIOS

Pin Assignments for I/O Connectors

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Before You Begin

DellInspiron™6000ServiceManual

Preparing to Work Inside the Computer

Recommended Tools

Computer Orientation

Screw Identification

Preparing to Work Inside the Computer



1. Ensure that the work surface is flat and clean to prevent scratching the computer cover.



2. Save any work in progress and exit all open programs.



3. Turn off the computer and all attached devices.



4. If the computer is connected to a docking device, undock it.



5. Disconnect the computer from the electrical outlet.



6. To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices.



7. Disconnect all other external cables from the computer.



8. Close the display and turn the computer upside down on a flat work surface.



9. Slide the battery-bay latch release on the bottom of the computer, and then remove the battery from the bay.

CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is

not covered by your warranty. Read and follow the safety instructions in the Product Information Guide that came with the computer.

CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of

your computer's electronic components. You can do so by touching an unpainted metal surface.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal

mounting bracket. Hold a component such as a microprocessor by its edges, not by its pins.

NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with

locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and

aligned.

NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer.

NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system, press

and hold the power button for 4 seconds.

NOTICE: To avoid damaging the system board, you must remove the main battery before you service the computer.

battery-bay latch release

Recommended Tools

The procedures in this document require the following tools:

l#1 Phillips screwdriver

l¼-inch flat-blade screwdriver

lSmall plastic scribe

lFlash BIOS update program (see the Dell Support website at support.dell.com)

Computer Orientation

Screw Identification

When you are removing and replacing components, print "Screw Identification" as a tool to lay out and keep track of the screws. The placemat provides the

number of screws and their sizes.

battery

front

left

back

right

Hard Drive:

(2 each)

Optical Drive:

(1 each)

Keyboard:

(2 each)



Modem:

Display Assembly:

Display Bezel:

Back to Contents Page



(1 each)



(4 each)



(rubber bumpers —6 each)

(screws —6 each)



Display Panel:

(8 each)

Palm Rest: (top)

(1 each)



Palm Rest: (bottom)

(13 each)



MCH Heat Sink

(2 each)

(1 each)—for a computer with a video card/thermal-cooling assembly



Fan:

(2 each)



Speakers:

(2 total —1 per speaker)



System Board:

(3 each)



Back to Contents Page

Flashing the BIOS

DellInspiron™6000ServiceManual



1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.



2. Insert the BIOS update program floppy disk or CD, and turn on the computer.

Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the

computer will automatically reboot.



3. Press <F2> during POST to enter the system setup program.



4. Press <Alt> and <f> to reset the computer defaults.



5. Press <Esc>, select Save changes and reboot, and press <Enter> to save configuration changes.



6. Remove the flash BIOS update program floppy disk or CD from the drive and restart the computer.

Back to Contents Page



NOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage.

NOTE: If you use a BIOS update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD.

NOTICE: Do not interrupt this process once it begins. Doing so may cause system damage.

Back to Contents Page

Internal Card With Bluetooth®Wireless Technology

DellInspiron™6000ServiceManual

Removing the Card

Replacing the Card

Removing the Card



1. Follow the instructions in "Preparing to Work Inside the Computer."



2. Remove the battery.



3. Use a plastic scribe to pry the card door open.



4. Disconnect the card from the card door ribbon.

CAUTION: Before you perform the following procedures, see the safety instructions in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTE: If you ordered an internal card with Bluetooth wireless technology with your computer, the card is already installed.

NOTICE: The card door has a ribbon that is connected to the internal card with Bluetooth wireless technology attached. Be careful when removing the

card door. Failure to do so could damage the ribbon cable and the Bluetooth card.

card door ribbon

internal card with Bluetooth wireless technology

card door

Replacing the Card



1. To replace the card, connect the card to the cable and insert it into the compartment.



2. Replace the card door by inserting the small center tab into the notch at the base of the compartment, and snap the door into place.



3. Replace the battery.

Back to Contents Page



card connector

internal card with Bluetooth wireless technology

Back to Contents Page

Coin-Cell Battery

DellInspiron™6000ServiceManual

Removing the Coin-Cell Battery

Replacing the Coin-Cell Battery

Removing the Coin-Cell Battery



1. Follow the instructions in "Preparing to Work Inside the Computer."



2. Remove the hinge cover.



3. Remove the keyboard.



4. Remove the tape that secures the coin-cell battery into place.



5. Use your finger or a plastic scribe to pry the battery from the system board.

Replacing the Coin-Cell Battery



1. When you replace the battery, insert it into the circular socket with the positive side up, and then push it into place.

Back to Contents Page



CAUTION: Before you perform the following procedures, see the safety instructions in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

tape

coin-cell battery

Back to Contents Page

Microprocessor Module

DellInspiron™6000ServiceManual

Removing the Microprocessor Module

Replacing the Microprocessor Module

Removing the Microprocessor Module



1. Follow the instructions in "Preparing to Work Inside the Computer."



2. Remove the Mini PCI card (if applicable) and the optical drive.



3. Remove the hard drive.



4. Remove the hinge cover.



5. Remove the keyboard.



6. Remove the display assembly.



7. Remove the palm rest.



8. Remove the microprocessor thermal-cooling assembly.



9. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.

CAUTION: Before you perform the following procedures, see the safety instructions in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE: Do not touch the processor die. Press and hold the microprocessor down on the substrate on which the die is mounted while turning the cam

screw to prevent intermittent contact between the cam screw and microprocessor.

NOTICE: To avoid damage to the microprocessor, hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTICE: To ensure maximum cooling for the microprocessor, do not touch the heat transfer areas on the microprocessor thermal-cooling assembly. The

oils in your skin reduce the heat transfer capability of the thermal pads.

NOTICE: When removing the microprocessor module, pull the module straight up. Be careful not to bend the pins on the microprocessor module.

ZIF socket

screwdriver (perpendicular

to microprocessor)



10. Lift the microprocessor module from the ZIF socket.

Replacing the Microprocessor Module



1. Align the pin-1 corner of the microprocessor module with the pin-1 corner of the ZIF socket, and insert the microprocessor module.

When the microprocessor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher

than the others, the module is not seated correctly.



2. Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board.



3. Perform the steps in "Removing the Microprocessor Module" in reverse order.



4. Update the BIOS using a flash BIOS update program floppy disk or CD. For instructions on how to flash the BIOS, see "Flashing the BIOS."

Back to Contents Page



ZIF-socket cam screw

pin-1 corner

NOTE: The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw, which indicates

the direction to turn the cam screw.

NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in

the ZIF socket does not require force.

NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and

ZIF socket.

NOTE: The pin-1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket.

NOTICE: You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket.

Otros manuales para Inspiron 6000

Tabla de contenidos

Otros manuales de Computadora portátil de Dell

Dell

Dell Adamo XPS Manual de usuario

Dell

Dell Inspiron 1150 Manual de usuario

Dell

Dell 15-7567 Manual de operación y mantenimiento

Dell

Dell Vostro 5470 Manual de operación y mantenimiento

Dell

Dell 9200 Manual de usuario

Dell

Dell Latitude 5300 2-in-1 Chrome Manual de operación y mantenimiento

Dell

Dell Precision 3561 Manual de operación y mantenimiento

Dell

Dell M1530 - XPS laptop. TUXEDO Instrucciones de uso

Dell

Dell PP01S Manual de usuario

Dell

Dell Latitude XT3 Manual de usuario

Dell

Dell Inspiron 15 Manual de usuario

Dell

Dell Inspiron 14R 5437 Manual de usuario

Dell

Dell XPS M1710 Manual de usuario

Dell

Dell Inspiron 1000 Guía de inicio rápido

Dell

Dell Inspiron 3584 Manual de usuario

Dell

Dell Inspiron 11 3000 Series Manual de usuario

Dell

Dell Inspiron 17 5000 Series Manual de usuario

Dell

Dell Inspiron 5580 Manual de usuario

Dell

Dell Vostro 1320 Manual de usuario

Dell

Dell XPS 14 Guía

Dell

Dell Latitude 3120 Guía del usuario

Dell

Dell Inspiron 2600 Guía del usuario

Dell

Dell XPS 13 9310 Manual de operación y mantenimiento

Dell

Dell Inspiron 13 7353 Manual de usuario

Manuales populares de Computadora portátil de otras marcas

HP ze2401xt - Pavilion Notebook PC Manual de usuario

Velocity

Velocity NoteMagix M10 Manual de usuario

Toshiba

Toshiba A105-S2236 Manual de usuario

HP ENVY 17 Manual

Winbook

Winbook LM Manual de usuario

HP PROBOOK 4520S Manual

Sony

Sony VAIO PCG-FX270 Manual de usuario

Sony

Sony VAIO PCG-R505JLK Manual de usuario

Lenovo

Lenovo THINKPAD X32 Manual de usuario

HP Compaq tc4200 Guía de inicio rápido

Toshiba

Toshiba mini NB300 Manual de usuario

Lenovo

Lenovo ThinkPad X201 Tablet Manual

Lenovo

Lenovo THINKPAD X31 Manual

Sony

Sony VGN-T240P VAIO Manual de usuario

Compaq

Compaq Armada E700 Series Manual de usuario

Fujitsu

Fujitsu Lifebook A6230 Manual de usuario

Acer

Acer Aspire ONE 722 Manual de usuario

Toshiba

Toshiba L300-EZ1524 Manual de usuario