Deif Delomatic 4 AOP-2 Guía
DM-4 Land/DM-4 Marine 4189340465C Replacement Instructions, AOP-2
DEIF A/S Page 1 of 4
Delomatic 4
DM-4 Land/DM-4 Marine
Document no.: 4189340465C
Replacement Instructions
AOP-2
DM-4 Land/DM-4 Marine 4189340465C Replacement Instructions, AOP-2
DEIF A/S Page 2 of 4
Table of contents
1. REPLACEMENT OF THE ADDITIONAL OPERATOR PANEL 2 (AOP-2) .............................3
GENERAL INSTRUCTION ................................................................................................................3
REPLACEMENT OF MODULE...........................................................................................................3
DM-4 Land/DM-4 Marine 4189340465C Replacement Instructions, AOP-2
DEIF A/S Page 3 of 4
1. Replacement of the Additional Operator Panel 2 (AOP-2)
General instruction
Before replacing any modules, please refer to the General Instruction for replacement of Delomatic
4 modules.
Please do not switch over modules from one DGU to another before consulting the
documentation provided by DEIF A/S, and preferably consulting DEIF A/S.
Please let us know if you do switch modules permanently, this will help us keep our records
updated. Call us or send a fax to DEIF A/S, for the attention of the service department:
Tel.: + 45 9614 9614 Fax: +45 9614 9615
When modules are replaced due to updating or due to any malfunctions, please let us know
the exact location of new modules.
Replacement of module
- Switch all equipment into switchboard control
- Remove the power supply from the defective DGU
- Remove other connections/plugs on the AOP-2
- Take out the text labels from the defective AOP-2 and insert these into the pockets on the
new AOP-2
- Connect the plugs and power supply again
- Set the CAN slave ID according to the correct configuration, please see the HMI setup
document
- Make a test to secure that the system works as predetermined
App./Bootl.
End Res.
Be aware of static electricity when handling!
DM-4 Land/DM-4 Marine 4189340465C Replacement Instructions, AOP-2
DEIF A/S Page 4 of 4
Setup of AOP-2 CAN no.
The AOP-2 needs a CAN no. to tell the system which AOP-2 it is on the BUS. If there is only one
AOP-2, the no. is set to 1. If there is more than one, they will be numbered 1, 2, 3 etc.
To set up the CAN no., first press the 2 buttons to the right for 5 sec. The no. is indicated with a
red light in the first left column of LEDs. If LED no.1 is on, it has no. 1, if LED no. 2 is on, it has
no. 2 and so on. To scroll up and down, use the two buttons to the right. To choose the selected
no., press the enter button. This button is also used to exit the setup. See the illustration below
to find the different buttons and LEDs.
LEDs 1-5 indicate CAN no. Enter/exit push-button. Push-buttons to enter
setup and change no.
of CAN.
Please notice:
If two displays have the same ID, LEDs 1-5 will flash quickly.
Button 6 - jump into the “ID change menu”.
DEIF A/S reserves the right to change any of the above.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Unidad de control de Deif
Deif
Deif Multi-line 2 Manual de instrucciones
Deif
Deif Multi-line 2 Manual de usuario
Deif
Deif CIO 308 Manual de usuario
Deif
Deif GPC-3 Hydro Manual de usuario
Deif
Deif GCU 100 Manual de usuario
Deif
Deif DELOMATIC 4 Series Suplemento
Deif
Deif PCM 4 Series Guía
Deif
Deif GCU 100 Manual de usuario
Deif
Deif PPU 300 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
