DAC-E2530EN-BJ DAC-E2530EN-BJ
18 19
For more detailed information, refer to the User Manual (at www.defibtech.com).
THE BATTERY PACK THE DEFIBTECH DATA CARD (OPTIONAL)
HOW TO INSERT AND
REMOVE THE BATTERY PACK
Before inserting the battery pack into the DDU-
2000 Series AED, ensure that the battery pack
opening in the back of the AED is clean and clear
of any foreign objects. Insert the battery pack
into the opening in the back of the AED.
Push the pack all the way in until the latch clicks.
The battery pack will only fit in one way. If the
battery pack does not fit, rotate the battery pack
before trying again. Once fully inserted, the
battery pack surface should be flush with the
back of the AED. Within moments of insertion,
the DDU-2000 Series AED will turn on and run
a battery pack insertion test. When the test is
completed, the unit will report the status of the
battery pack and shut down. (Note: The battery
pack must have been removed from the unit for
at least 10 seconds for the battery pack self-test
to be performed automatically.)
To remove the battery pack, push the battery
pack eject release latch. After the battery pack
is partially ejected, pull the battery pack out.
WHEN TO REPLACE THE BATTERY PACK
It is important to check the expiration date of the
battery pack. The battery pack should be used
before the expiration date. When the battery
pack is low, the unit will indicate “battery low”
or “replace battery now” and the Active Status
Indicator will flash red. The battery pack should
be replaced immediately. Use only Defibtech
battery packs.
You may check the status of the battery pack
when the unit is off by pressing the center
softkey button to display the AED Status Screen.
The expiration date is also printed on the label on
the battery pack as shown at right.
Battery Pack Label
Located Here
HOW TO INSERT AND REMOVE THE DEFIBTECH DATA CARD
The optional Defibtech Data Card (DDC card) is used to store event and audio information
collected by the AED. All DDU-2000 Series AEDs will operate without DDC cards and will still
store select event information internally. Information stored on the DDC card is retrievable
with a separate Defibtech PC-based software package. (Refer to the “DefibView” section of
the DDU-2000 Series User Manual available at www.defibtech.com.)
Before installing the DDC card, ensure the AED is turned OFF.
Locate the data card/USB port access door on the right-hand
side of the unit. Open the data card/USB port access door
by slightly pushing and then sliding the door down to release
the latch. The door will spring open. Insert the DDC card into
the thin slot in the side of the AED centered above the USB
port opening, notched end first, label side up, until it clicks
into place. The card should be flush with the surface of the
slot. If the card does not push in all the way, it may have been
inserted upside down. In that case, remove the card, flip it
over, and try inserting it again.
To remove the DDC card, press the card as far as it will go
and then release. Upon release, the DDC card will be partially ejected and can be removed by
pulling the DDC card the rest of the way out.
Close the data card/USB port access door by closing and then pushing the door up until the
door latch engages.
Note: DDU-2000 Series AEDs running software version 1.3 or below may not function with
certain DDC Cards. Contact Defibtech for support (refer to page 32 for contact information).
EVENT DATA
As part of Defibtech’s on-going regulatory compliance activities, event data shared with
Defibtech may be used by Defibtech to fulfill regulatory obligations. Any identifying personal
data or health information received is considered confidential within Defibtech and will not be
used for any other purpose. Please contact Defibtech at support@defibtech.com should there
be any further questions.
!
CAUTION
Using non-Defibtech Data Cards (DDC cards) may damage
the unit and will void the warranty.
