DCSENG S-Cutter S-150 Manual de usuario
PIPE(TUBE) CUTTER Of Best Technology
Safety Precautions
Thank you for purchasing S-Cutter.
This is an instruction to prevent property damage, ensure the correct use and safety of the user.
Please read these instructions carefully before use.
Manual
( )
PIPE(TUBE) CUTTER Of Best Technology
CONTENTS
1. Precautions for the safe use 03
2. Please keep the following precautions 05
3. Check before use 07
4. How to use S-150 08
5. Quality Warranty 37
S-Cutter 3
01 Keep work area clean.
Untidy workshop and work table may cause accidents.
02 Consider your work environment.
Do not let it wet.
Do not use in damp or humid place.
Install bright lighting in the work place.
Do not use near flammable liquids or gases.
03 Protect from electric shock.
Avoid to touch grounded parts
(i. e. water pipes, heaters, microwave ranges, refrigerators).
Use it grounded.
04 Do not let outsiders access.
Do not let the outsiders in contact with tool or extension cord.
Do not let visitors access to the work area.
05 Keep the product safe.
Cut off the power when the tool is not in use, and keep it where it is not
accessible to outsiders .
06 Do not work in an overload condition.
Within the range of the specified output allows you to work more efficiently and
securely.
07 Always use the proper tools.
Use the supplied standard accessories.
Do not use tools outside of the scope of work or the intended use of the tool.
08 Dress properly.
Do not wear loose clothing or jewelry. You may be hurt by the moving parts of
the tool.
It is recommended to wear non-slip footwear for outdoor work.
09 Use protective glasses and gloves.
Scattering tips can cause serious injury to the eyes, or injury, such as burns.
10 Do not abuse the cord.
Do not drag the product by grasping the wire.
Do not pull the wire when disconnecting the plug.
Protect wire from heat, oil and sharp edges.
11 Secure the workpiece.
Secure the workpiece by using a lock.
Precautions for the safe use
PIPE(TUBE) CUTTER Of Best Technology
4 www.s-cutter.co.kr
12
Focus on the job.
Please note the fall, and cut piping pinch.
13
Manage the product carefully.
keep the product clean and efficient for safe operation.
Manage with the proper lubricant, apply a corrosion inhibitor to prevent corrosion when
not in use for a long time.
When replacing the management regulations and tools, comply with the instructions.
Check plugs and wires regularly and contact experts to repair the damage.
Check connection cables regularly and replace damaged parts.
Keep the control board dry and avoid getting oil or grease.
14
Remove power.
When not in use, checked, or replaced, turn off the switch.
(Press the emergency stop switch before work.)
15
Please check before operation.
Make sure that the tool(blade) has been tightened, blade direction and the direction of
rotation.
Make sure that the piping is tightened.
Make sure the piping direction of rotation. (Check reverse rotation switch Forward(CW))
Make sure that the cutting, beveling speed and rotational speed.
16
Be careful of operating the machine accidently.
Do not carry when the power is connected.
When turning on, make sure that the operation switch is off.
17
Connecting wires outdoor
The wiring is licensed for the purpose of using the corresponding display.
18
Be cautious all the time.
Observe work process and process accordingly.
Do not use this product if the concentration is blurred,
Do not operate by force the cutting speed and rotational speed.
19
Make sure that there is no damage on the product.
Make sure that safety devices or slightly damaged parts operate perfectly before reuse.
Make sure that the product is not stuck or damaged.
The perfect operation is guaranteed only if all the parts are perfectly assembled and
adjusted.
Damaged safety devices or parts must be replaced or repaired in customer service
center unless it was mentioned differently.
20
Caution!
For your safety, use the parts and tools indicated on the manual or recommended by the
manufacturer.
Use of other parts or additional tools that are not recommended on the manual and
catalog may occur accidents.
21
Repair request to the experts
The product supplied is matched to the corresponding safety regulations.
The repairs should be referred to a qualified technician and if not, there is a risk of
accidents.
S-Cutter 5
The instructions in this owner's manual contain information that is important to the safe use
of this product.
Not following these instructions can cause death, serious injury, and massive property
damage.
‘Warning’and‘Caution’are indicated and the meanings are as below.
Sign Description
Warning
Serious injury or death may occur, if the instruction is violated.
Caution Serious injury or death may occur, if the instruction is violated.
Failure or performance degradation may occur, if the instruction is violated.
In order to prevent accidents that may occur when handling or using this product,
precautions are recorded. As these warnings and cautions do not indicate all the cases
that may occur,
please pay attention when working or storing. Read carefully to avoid accidents.
Special safety precautions
'warning' or 'caution' are a caution: Injury or danger may occur under certain conditions.
Please keep the following precautions
PIPE(TUBE) CUTTER Of Best Technology
6 www.s-cutter.co.kr
Make sure the power is connected to the ground.●
Leakage current due to electric shock may occur if the product is not connected to the grounding.
● Do not pour water or cutting fluid.
Due to water or other liquids on the electric motor, electric shock, or death may occur.
Use cutting fluid until tools are slightly wet.
Do not use tools in wet conditions or rain.●
Serious injury or death may occur by electric shock.
Avoid fingers, hands or clothes to touch the blade while operating.●
When fingers, hands, or other body parts stuck in the machine, it may occur serious injury.
Avoid fingers, hands or other body parts to touch where pipe and roller meet while operating.●
When fingers, hands, or other body parts stuck in the machine, it may occur serious injury.
Before supplying power to the product, be sure to turn off the operation switch.●
Plugging in with the switch on may cause sudden rotation and occur serious injury.
Do not let any part of body to touch the compression device of product.●
Serious injury may result.
● Make sure to wear safety equipment.
Chips generated during the operation may scatter and cause serious eye injury.
Use certified tips (Over national certification) for indicated methods.●
If violated, performance degradation and serious injury may occur.
Do not leave the product rotated.●
Workers may result in bodily injury.
Place cutting chips safely.●
When cutting chips meet flammable substances, it may cause fire and burns.
Wear gloves and long-sleeved clothes to wear.●
Scattering chips can cause burns.
Use Extension cord as short as possible.●
If too long or too thin, it may cause overload.
Operation before commissioning.●
Check the machine before use for safety.
Warning
Caution
S-Cutter 7
1. Check the circuit breaker
Make sure the system is powered on the circuit breaker is installed.
Check that earth leakage breakers are installed in every power system.
Make sure that the ground wire is connected to the powered system.
2. Extension cord
When far away from the location of the power use an extension cord. Use the
connecting cord appropriate length and thickness of the flow of current, in order not to
interfere. If too long or too thin, it may cause overload and lower the power of the
motor. Use it as short as possible.
3. Check the power
Be sure to use the power listed on the nameplate.
4. Check the switch is off
If the cord is damaged it must be replaced or repaired immediately.
Unaware that the switch is turned on, the number of accidents due
to a sudden rotation of the plug is inserted in the power being.
Checked before use
PIPE(TUBE) CUTTER Of Best Technology
8 www.s-cutter.co.kr
150
Cut, whether thick or thin, at a single stroke!
The world best convenience and work speed !
Equipment capacity : 1/4inch - 6inch (Pipe O.D 6mm - 170mm)
S-Cutter 9
How to use the product
How to use S-150
Before use
Please read about how to use manual provided by the headquarter or suppliers.
Users must be educated before use.
Make sure to remove the power exchanges when cutting or beveling.
Make sure to connect the grounding, and confirm the voltage.
Make sure to wear protective equipment such as protective glasses before work.
Beware of burns when using beveling tools which is extremely hot after operation.
Beware of burns by gearbox in case of prolonged use.
INDEX
01. Names of parts and controls
02. Cutting and Beveling blade installation
03. Pipe setting
04. Adjusting the Cutting & Beveling
05. Rotate Adjustment
06. Emergency stop switch
07. Maintenance and inspection
08. Product Specifications
PIPE(TUBE) CUTTER Of Best Technology
10 www.s-cutter.co.kr
1.
Names of parts and controls
Names of parts●
NO Name Function
1 S-150 Pipe Cutting Machine
2 S-150_MT Machine Table
3 S-150_RS Pipe Transfer Device
4 S-150_VS Short Pipe Support and Transfer (fixed)
5 S-150_VS Long Pipe Support and Transfer (mobile)
6 Locking Lever Positioning Bolt According to the Diameter
7 Chip holder Cutting Chip Holder
Este manual sirve para los siguientes modelos
1
Otros manuales de Cortador de DCSENG
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
