DCSENG S-CM4_M Manual de usuario

PIPE(TUBE) CUTTER Of Best Technology

Manual

( ( CM4_M / CM4_OD) SAFETY PRECAUTIONS

Thanks for choosing the S-Cutter. Make sure that you carefully read and fully understand the Manual to use the device correctly and keep yourself and your properties safe.

PIPE(TUBE) CUTTER Of Best Technology

CONTENTS

1. SAFETY PRECAUTIONS032. Must-Follow Rules063. Instruction Before Use084. How to Use ● S-CM4_M10 ● S-CM4_OD235. Quality Warranty30

S-Cutter 301Keep workplace clean and well-lit at all times.An untidy or dark workplace may cause accidents.02Consider your work environment.Do not let it wet.Do not use in humid place.Install bright lighting in the work place.Do not use the machine near the flammable liquids or gases.03Keep yourself safe from electric shock.Do not touch the grounded parts(i.e. Water pipes, heaters, ranges, refrigerators).Ensure the grounding wire is properly connected to the ground and use it.04Keep out any unauthorized persons.Do not let the outsiders contact with tool or extension cord.Do not let visitors access to the work area.05Keep the product safe.Cut off the power when the tool is not in use, and keep it where it is notaccessible to outsiders.06Do NOT operate at overload.More efficient and safe operations are enabled within a permitted power range. 07Always use the proper tools.Use the standard parts and components provided by the head office. Do not use the tool for purposes other than their intended use or in

places

away from the working range. 08Dress properly.Do not wear loose clothing or jewelry. You may be hurt by the moving parts of the tool.It is recommended to wear non-slip footwear for outdoor work.09Be sure to wear safety glasses and protective gloves.Wearing safety gear such as goggles and gloves can reduce the risk of bodily injury.Flying chips can do serious damage to the eyes or cause a burn.SAFETY PRECAUTIONS

PIPE(TUBE) CUTTER Of Best Technology 4 www.s-cutter.co.kr10Do NOT abuse the cord.Do not drag the product by pulling the electric cord.Do not unplug the cable by pulling the cord itself. Keep the cord safe from heat, oil and sharp edges.11Install the anti-scattering protector of cutting chips.Fire might occur if cutting chips touch the inflammable, and burning

might

occur if it touches the body.spattering chips during work might cause injury to other workers around

the

working spot.12Pay attention to your work.Please note the fall and cut piping pinch.13Manage the product carefully.Keep the product clean and efficient for safe operation.Manage with the proper lubricant, apply a corrosion inhibitor to prevent corrosion when not in use for a long time.When replacing the management regulations and tools, comply with the instructions.Check plugs and wires regularly and contact experts to repair the damage.Check connection cables regularly and replace damaged parts.Keep the control board dry and avoid getting oil or grease.14Remove from power source.When not in use, checked or replaced, turn off the switch.15Please check before operation.Make sure that the tool(insert tip) has been tightened.16Be careful of operating the machine accidently.Do not carry when the power is connected.When turning on, make sure that the operation switch is off.17Electrical cable for connection outdoors.Use the authorized extension poser cord with a qualifying mark.Do not connect the currently used cable to other equipment. Have a separate circuit breaker.

S-Cutter 518Be cautious all the time.Observe work process and process accordingly.Do not use this product if the concentration is blurred,Do not operate by force the cutting speed and rotational speed.19Make sure that there is no damage on the product.Check the safety device and examine thoroughly that the mildly

damaged

parts now function normally before resuming the use of the tool. Check if the Product got stuck, or the parts are damaged. The complete operation of the tool is not guaranteed unless all parts

are

normally assembled, and all requirements are met. Unless otherwise stated in the Manual, the damaged safety device or

parts

are repaired or replaced at the customer service center. 20Caution!For your safety, use the parts and tools indicated on the manual or recommended by the manufacturer.Use of other parts or additional tools that are not recommended on

the

manual and catalog may occur accidents.21Repair request to the expertsFor your safety, use the tools and accessories specified in the Manual

recommended by the distributor. The use of other tools and accessories

not

mentioned in the Manual or catalogue may result in bodily injury.

PIPE(TUBE) CUTTER Of Best Technology 6 www.s-cutter.co.krThe instructions in this user manual contains information that is important to the safe use of this product.Not following these instructions can cause death, serious injury, and massive property damage.For safety, the instructions are divided into ‘WARNING’ and ‘CAUTION’ depending on degree of risk, and the details are as follows:SymbolDescriptionWarning※ There is a high possibility of serious injury or death when the instructions are violated.Caution※ There is a possibility of serious injury or death when the instructions are violated.※ There is a possibility of device failure or degradation when the instructions are violated.Precautions were recorded to prevent an accident that might easily occur while

using

or handling the Product and execute operations safely. The safety warnings and cautions cannot cover all conditions or situations that

can

take place during operation. Therefore, remain focused during operation or

storing.

Read and fully understand the Manual to prevent an accident. Special safety precautions‘WARNING’ or ‘CAUTION’ mark makes a user stay alert because there is a possibility of hazards under particular conditions. Must-Follow Rules

S-Cutter 7● Be sure to apply our supplied product and insert tip only for their intended uses. Use only products certified for their quality (state-certified or higher-quality) in the event there is difficulty in procuring our products and accessories. If violated, performance degradation and serious injury may occur.● Do not leave the product rotated. workers may result in bodily injury.● Place cutting chips safely. When cutting chips meet flammable substances, it may cause fire and burns.● Wear gloves and long-sleeved clothes to wear. Scattering chips can cause burns.● Use Extension cord as short as possible. If too long or too thin, it may cause overload.● Operation before commissioning. Check the machine before use for safety.● Do not pour water or cutting fluid. Due to water or other liquids on the electric motor, electric shock, or death may occur.● Do not use tools in wet conditions or rain. Serious injury or death may occur by electric shock.● Avoid fingers, hands or clothes to touch the blade while operating. When fingers, hands, or other body parts stuck in the machine, it may occur serious injury.● Avoid fingers, hands or other body parts to touch where pipe and roller meet while operating. When fingers, hands, or other body parts stuck in the machine, it may occur serious injury.● Before supplying power to the product, be sure to turn off the operation switch. Plugging in with the switch on may cause sudden rotation and occur serious injury.● Do not let any part of body to touch the compression device of product. Serious injury may result.● Make sure to wear safety equipment. Chips generated during the operation may scatter and cause serious eye injury.WarningCaution

PIPE(TUBE) CUTTER Of Best Technology 8 www.s-cutter.co.kr1.Check the electric leakage breakerMake sure the system is powered on the circuit breaker is installed.Check if an electric leakage breaker (ELB) with rated capacity is installed in all electric units.Make sure that the ground wire is connected to the powered system.2.Extension power cordIf an electrical outlet is not nearby, use an extension power cord. Choose a proper one in terms of length and thickness, considering the flow of electricity. If it is too long or thin, voltage increases, causing overload. Use a short power cord as much as possible. ※ Specification of the extension cord has to be at least × 



(250V-16A).3.Check the powerCheck the power supply stated on the nameplate and use the proper power source. 4.Check the switch is offIf an electric power cord is damaged, it must be repaired or replaced with a new one immediately. Unaware that the switch is turned on, the number of accidents due to a sudden rotation of the plug is inserted in the power being.Instruction before use

S-Cutter 9

CM4_M

Portable hand bevel and coating removalBevel capacity : 0-90°, 0-14CPipe/plate : coating removal(zinc coating) and bevel processing

PIPE(TUBE) CUTTER Of Best Technology 10 www.s-cutter.co.krHow to Use S-CM4_M How to Use S-CM4_M Instructions Before Use Please read about how to use manual provided by the headquarter or suppliers.Users must be educated before use.Make sure to remove the power when changing the insert tip.Be sure to use consumables(such as insert tip) for this equipment that are provided by us. Make sure to confirm the voltage and install the electric leakage breaker with rated capacity.Make sure to wear protective equipment such as protective glasses before work.Beware of burns by gearbox in case of prolonged use. INDEX 01.Name and function of the parts02.Accessories03.How to adjust the bevel angle 04.How to adjust the guide roll05.How to adjust the processing depth 06.How to change the insert tip07.How to use the S-CM4_M08.Product specifications