DaytonAudio DTA-2 Manual de usuario
Model: DTA-2 User Manual
Introduction:
The Class-T Digital Audio Amplifier is designed around the Tripath TA-2024 IC. The TA2024 is a
15W/ch continuous average two-channel Class-T Digital Audio Power Amplifier IC using Tripath’s
proprietary Digital Power Processing™ technology. Class-T amplifiers offer both the audio fidelity
of a Class-AB amplifier and the power efficiency of a Class-D amplifier.
This PCB amplifier is ideal for any audio enthusiast who enjoys building and modifying speaker
systems. The applications are virtually limitless since this tiny PCB measures a mere 2-11/16" x
1-5/16". Build your own speakers or incorporate the amplifier into an existing speaker cabinet.
Features:
• Class-T architecture
• “Audiophile” Quality Sound
• 0.03% THD+N @ 9W, 4Ω
• 0.10% IHF-IM @ 1W, 4Ω
• 11W @ 4Ω, 0.1% THD+N
• 6W @ 8Ω, 0.1% THD+N
Package Contents:
(1) Class T Digital Audio Amplifier PCB
(1) Volume control PCB with 12" ribbon cable
(1) LED power indicator
(2) 12" Speaker Wires (Red & Black)
(2) 12" Power Wires (1 Red & 1 Black)
(2) 12" LED Wires (1 Red & 1 Black)
(2) Output Capacitors
(2) Ferrite Cores
Assembly:
• Remove the amplifier PCB from the static protective sleeve using static protective gloves or
wrist band
• Solder the speaker wires to the PCB at points “A & B”
• There are polarity marks (L+/- R+/-) printed on the bottom of the PCB
• Solder the power leads (if desired) at point “C”
• There are polarity marks (B+/B-) printed on the bottom of the PCB
• High Efficiency
• 81% @ 15W, 4Ω
• 90% @ 10W, 8Ω
• Dynamic Range = 98 dB
• Over-current protection
• Over-temperature protection
• High Power
• 15W @ 4Ω, 10% THD+N
• 10W @ 8Ω, 10% THD+N
The schematic diagram above is provided for reference. It illustrates the TA-2024 IC and the input
and output circuits on the PCB. CDO are two output capacitors. These capacitors are ideally
placed close to the speaker terminals or crossover input terminals as appropriate.
• Solder the LED to the PCB at point “D” or use the LED wires to place the
LED where desired
• The anode (+) lead is long, the cathode (-) is short
• Mount the LED from the bottom of the PCB
• Insert the anode through the left eyelet and the cathode through the right eyelet
• Wrap each speaker wire through a ferrite core; one wrap per core is all that is required
• Solder the speaker wires to the speaker terminals
• Solder an output capacitor across the speaker terminals in parallel with the speaker wires
• Connect power via the power leads or DC power jack; we recommend a 12VDC, 2000mA power
supply similar to Parts Express model 120-052
• Mount the volume control in the desired location and connect to the amplifier PCB using the 12"
ribbon cable
• Mount the PCB using adhesive pads or with a zip tie
Schematic Diagram:
Dayton Audio®Last Revised: 4/5/2016
daytonaudio.com
tel + 937.743.8248
info@daytonaudio.com
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
Warranty Information
Dayton Audio products are warranted free from defects in material and workmanship for 5 years from
date of purchase (see exceptions below). In the rare case of a product failure, please contact your place of
purchase or call our Customer Support Department at (937) 743-8248.
Warranty Limitations
There are no other warranties, either express or implied, that extend the foregoing, and there are no
warranties of merchantability or fitness for any particular purpose. Dayton Audio is not responsible for any
consequential on inconsequential damage to any other unit or component or the cost for installation or
extraction of any component of the audio system, or for the improper use of products. This includes but is
not limited to burnt voice coils, overheating, bent frames, holes in the cone, or broken lead wires. Warranty
does not apply to misuse, abuse, neglect, accident, improper use, etc. Dayton Audio reserves the right to
repair or replace the products with either a new or factory refurbished unit.
Exception: Dayton Audio HDMI Cables -- No registration, no questions asked LIFETIME warranty.
Replacement of Dayton Audio HDMI cables is with equal or better quality HDMI cables. Unassembled Kits -
A 45-day return policy applies to unassembled kits. Once assembly has been started or completed, kits are
deemed used and are nonreturnable for refund/exchange. This does not limit the manufacturers' warranty
policies on any kit component.
This warranty gives you specific legal rights and you may also have other rights that vary from state to state.
Non-Warranty Service: If non-warranty service is required, the product may be sent to the Company for
repair/replacement, transportation prepaid, by calling (937) 743-8248 for details, complete instructions, and
service fee charges.
Tabla de contenidos
Otros manuales de Amplificador de DaytonAudio
DaytonAudio
DaytonAudio DTA-100ST Manual de usuario
DaytonAudio
DaytonAudio SA1000 Manual de usuario
DaytonAudio
DaytonAudio SA25 Manual de usuario
DaytonAudio
DaytonAudio MA1240a Manual de usuario
DaytonAudio
DaytonAudio WF150A Manual de usuario
DaytonAudio
DaytonAudio MA1240a Manual de usuario
DaytonAudio
DaytonAudio DTA-PRO Manual de usuario
DaytonAudio
DaytonAudio KABX Manual de usuario
DaytonAudio
DaytonAudio DTA-120BT Manual de usuario
DaytonAudio
DaytonAudio MCA3545 Manual de usuario
DaytonAudio
DaytonAudio WF40A Manual de usuario
DaytonAudio
DaytonAudio PMA800DSP Manual de usuario
DaytonAudio
DaytonAudio HTA100BT Manual de usuario
DaytonAudio
DaytonAudio APA1200DSP Manual de usuario
DaytonAudio
DaytonAudio WF150A Manual de usuario
DaytonAudio
DaytonAudio SPA300-D Manual de usuario
DaytonAudio
DaytonAudio SA100 Manual de usuario
DaytonAudio
DaytonAudio MA1240A Manual de usuario
DaytonAudio
DaytonAudio DSPB Series Manual de usuario
DaytonAudio
DaytonAudio HTA100 Manual de usuario
