Datamax M-Class Mark II Manual de usuario

Present Sensor Option

92-2476-01 Rev.C

Contents of the Present Sensor Kit

This kit contains the following item:

Present Sensor Option

Follow the steps listed below to install this option.

Step 1: Preparing the Printer

Turn ‘Off’ the power switch and unplug the

printer.

Open the cover. Remove any installed media

from the printer.

Remove the Fascia by gently pulling it forward.

Loosen and remove the Thumbscrew, then

remove the Tear Plate.

Fascia Tear Plate

Thumbscrew

Step 2: Installing the Present Sensor

Position the Present Sensor for mounting on the

front of the printer.

Using the Thumbscrew, secure the Present

Sensor to the printer, as shown.

This completes the installation process.

Proceed to Loading Media.

Thumbscrew

Present Sensor

Loading Media

Load media into the printer as you normally would for tear-off operation (see the Operator’s Manual for

details). When equipped with the Present Sensor option, labels printed in a batch will be dispensed “on-

demand” – that is, printing will occur only after a previously printed label has been removed from the

printer.

Setup, Configuration, and Operation

The Present Sensor is plug and play; no setup or configuration is required. As soon as power is applied, the

printer senses and enables the Present Sensor for operation.

During operation, when a label is present (blocking the sensor), the yellow Stop Light on the front panel of

the printer will flash to prompt you that a label awaits removal.

With printers equipped with an LCD display, the display will read “REMOVE LABEL”

Notes: (1) The operation of the Present Sensor can also be controlled via software commands from the host. Be

sure that your software program is properly configured for use with this option. (2) If the Present Sensor is

disconnected without first powering off the printer, the printer will behave as if there is a label blocking the

sensor. Turn the printer off and then back on. The printer will reconfigure itself to operate without the

Present Option

Present Sensor Maintenance

No regularly scheduled maintenance of the Present Sensor is required, however, for trouble-free operation

be sure to keep the sensor free of debris and dust. To clean the Present Sensor:

CAUTION

For your safety and to avoid damaging the printer, turn ‘Off’ and unplug the printer before cleaning; and

take proper precautions when using isopropyl alcohol, a flammable liquid.

Turn off and unplug the printer. Remove any media.

Using a Cotton Swab or compressed air, wipe or dust

off the Sensors.

(In cases of extreme build-up, a cotton swab

dampened with isopropyl alcohol can be used to

clean the Sensors.)

If alcohol was used, allow the Sensors to dry;

otherwise, go to Step 4.

This completes the cleaning procedure. Reinstall

media. Plug in and turn on the printer.

Sensors

Cotton Swab

Otros manuales para M-Class Mark II

Tabla de contenidos

Otros manuales de Etiquetadora de Datamax

Datamax

Datamax M-Class Mark II Manual de usuario

Datamax

Datamax E-Class Mark III Manual de usuario

Datamax

Datamax A-Class Mark II Manual de usuario

Datamax

Datamax LP3 Manual de usuario

Datamax

Datamax I-Class Mark II I-4212E/203 Manual de usuario

Datamax

Datamax I-Class Manual de usuario

Datamax

Datamax H-Class Manual de usuario

Datamax

Datamax Prodigy Manual de usuario

Datamax

Datamax MICROFLASH 4TE Manual de usuario

Datamax

Datamax RL4e Manual de usuario

Datamax

Datamax RL3 Manual de usuario

Datamax

Datamax M-Class Mark II Manual de usuario

Datamax

Datamax A-Class A-4212 Manual de usuario

Datamax

Datamax Perfomance Series Manual de usuario

Datamax

Datamax I-Class Mark II Manual de usuario

Datamax

Datamax M-Class Mark II Manual de usuario

Datamax

Datamax Workstation w1110 Manual de usuario

Datamax

Datamax E-Class Mark III Professional+ Manual de usuario

Datamax

Datamax I-Class Mark II Manual de usuario

Datamax

Datamax Prodigy Plus Manual de usuario

Datamax

Datamax I-class series Manual de usuario

Datamax

Datamax MICROFLASH 4T Manual de usuario

Datamax

Datamax H-Class Manual de usuario

Datamax

Datamax E Class E-4203 Manual de usuario

Manuales populares de Etiquetadora de otras marcas

Brother

Brother P-Touch 2420PC Manual de usuario

newell

newell Dymo LabelManager 210D Manual de usuario

Brother

Brother TD-4000 Manual de usuario

U-Line

U-Line BROTHER H-8754 Manual de usuario

Tharo Systems

Tharo Systems H-435+ Manual de usuario

Brother

Brother E300 Manual de usuario

Godex

Godex RT700 SERIES Manual de usuario

ID Technology

ID Technology 252 Manual de usuario

Labelmate

Labelmate MC-11 Manual de usuario

CAB

CAB XD4M/300 Manual de usuario

Avery Dennison

Avery Dennison Pathfinder 6057 Manual de servicio

Brother

Brother P-touch PT-9700PC Manual de usuario

TSC

TSC PEX1000 Series Manual de usuario

Adkins

Adkins Label Master Manual de usuario

Epson

Epson LabelWorks LW-400 Manual de usuario

Primera

Primera 510212 Manual de usuario

Brady

Brady BradyPrinter S3100 Manual de usuario

DuraLabel

DuraLabel LabPRO Manual de usuario