Danfoss APP 1.5-2.5 Manual de usuario

180R9091

521B0741 DKCFN.PI.013.EF4.02 08-2013

180R9091

INSTRUCTION

Internal pump elements

APP 1.5-2.5

To understand the pump design better, please see exploded view on last

page.

1. Unscrew the 4 mounting screws and remove the seal SAE

ange. Do not yet unscrew the 2 lower screws.

2. Wet the shaft and shaft seal with clean (ltered) soap-water.

Gently lever the shaft seal assembly free using 2 screwdrivers.

3. Unscrew the 2 lower screws.

This document covers the instructions for changing internal pump elements on the axial piston pumps APP 1.5-2.5

Note: It is essential that the pump is serviced in conditions of absolute cleanliness.

Tools needed:

. Toolset (code no. 180B4148)

. Shaft bush

. Press bush

. Allen key 5 mm

. 2 screwdrivers

4. Carefully turn the whole pump over so that the shaft is facing

down. Support the pump in a suitable hollow base so that the

pump is not supported by the shaft.

5. Remove the housing.

2 DKCFN.PI.013.EF4.02 521B0741

6. Remove the pistons, retaining plate, retaining ball, spring guide

and spring from the cylinder barrel.

7. Remove the cylinder barrel.

8. Remove the port plate.

9. Gently lever the valve plate assembly free with the aid of a

screw-driver.

10. Replace the O-rings and the back-up rings on the valve plate.

Mount the new back-up rings on the new valve plate rst and

then mount the new O-rings.

Mount backup ring rst

Then mount the O-ring

521B0741 DKCFN.PI.013.EF4.02 3

11. Wet the O-rings and back-up rings with clean (ltered) soap-

water.

12. Gently press, by hand, the valve onto the cylinder barrel.

13. Gently push ushing valve out using the Allen key.

14. Remove spring from poppet and poppet guide and remove

O-ring from poppet guide.

15. Press new spring onto shoulders of poppet guide and poppet

so it is stuck on both collars. Then mount new O-ring on poppet

guide.

16. Turn ushing valve upside down. If not properly assembled,

spring will fall o.

17. Mount ushing valve by pressing it into the hole.

18. Position the port plate over the guide pin.

IMPORTANT: Make sure that the guide pin is located in the

locating hole in the port plate. )

19. Replace the O-ring on the port ange and position the new

cylinder barrel on the port plate.

Guide pin

Locating hole

O-ring

4 DKCFN.PI.013.EF4.02 521B0741

20. Position the new spring, new spring guide, new retainer guide,

new retainer plate and new pistions.

21. Position the housing on the port ange and over the guide pin.

22. Hold the pump together and carefully turn it over to rest on the

housing. To prevent seizing-up, lubricate the threads on the 2

screws and screw them into the port ange and the housing.

Use Molykote D paste from Dow Corning or Klüber UH1 84-201

from Klüber lubrication. Tighten the 2 ange screws to a torque

of 12+1Nm.

521B0741 DKCFN.PI.013.EF4.02 5

23. Mount the new shaft seal following the instructions in changing

“Shaft seal - APP 1.5 - 2.5” (180R9089)

Wet the torpedo and new shaft seal with soap. Do not use

silicone grease.

Slide the shaft seal over the torpedo with the carbon seal face

pointing upwards. Be careful not to damage the carbon seal

face on the shaft seal.

24. Replace the O-ring on the SAE ange

25. Lubricate the threads on the 4 screws with grease and screw

them into the pump and tighten by hand. Use Molykote D

paste from Dow Corning or Klüber UH1 84-201 from Klüber

lubrication

Selection of spare parts

Please nd our APP part list 521B0941 on www.ro-solutions.com

6 DKCFN.PI.013.EF4.02 521B0741

Exploded view

Tabla de contenidos

Otros manuales de Bomba de agua de Danfoss

Danfoss

Danfoss H1P 045 Manual

Danfoss

Danfoss iSave 21 Manual de usuario

Danfoss

Danfoss H1 Series Manual

Danfoss

Danfoss APP 21-43 Manual de usuario

Danfoss

Danfoss KSV Series Manual de usuario

Danfoss

Danfoss RSH Series Manual de usuario

Danfoss

Danfoss PAH Series Manual de usuario

Danfoss

Danfoss APP 1.5 Manual de usuario

Danfoss

Danfoss H1 078 Manual de usuario

Danfoss

Danfoss H1T 045 Manual de usuario

Danfoss

Danfoss APP series Manual de usuario

Danfoss

Danfoss PAH 50 Manual de usuario

Danfoss

Danfoss 45 Frame K2 Series Manual de usuario

Danfoss

Danfoss H1 Series Manual de usuario

Danfoss

Danfoss PAHT G 10 Manual de usuario

Danfoss

Danfoss MSV-F DN 15-400 Manual de usuario

Danfoss

Danfoss H1 115 Manual

Danfoss

Danfoss APP 11-13 Manual de usuario

Danfoss

Danfoss Optyma OP-HRSM0750NC211Q Manual de usuario

Danfoss

Danfoss 45 K2 Series Guía de configuración

Danfoss

Danfoss Series 40 M46 Tandem Manual de usuario

Danfoss

Danfoss APP 1.5 Manual de usuario

Danfoss

Danfoss PAHF 20 Manual de usuario

Danfoss

Danfoss PAH Series Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario