Danfoss FP735Si Manual de usuario
FP735Si
Electronic 3-Channel Full Programmer for
Heating and Hot Water with Service Interval Timer
Danfoss Heating
MAKING MODERN LIVING POSSIBLE
Installation Guide
FP735SI
2
GB
For a large print version of these instructions
please call Marketing on 0845 121 7400.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
This product complies with the following EC Directives:
Electro-Magnetic Compatibility Directive.
(EMC) (2004/108/EC)
Low voltage Directive.
(LVD) (2006/95/EC)
®
Certification Mark
Danfoss Heating 3
GBGB
Index
1.0 Installation Guide................................................................................4
2.0 System Overview .................................................................................4
3.0 Installation..............................................................................................5
3.1 Removing the wallplate.............................................................5
3.2 Installation considerations........................................................5
3.3 Wiring ...............................................................................................5
3.3 Mounting the unit........................................................................6
3.4 Unit startup.....................................................................................6
4.0 Programming Options ......................................................................6
4.1 Normal programming.................................................................6
4.2 Advanced programming ...........................................................7
5.0 Pre-programmed Parameters........................................................8
5.1 Advanced programming ...........................................................8
5.2 Normal programming.................................................................8
6.0 Display Information......................................................................... 10
7.0 Advanced Programming ............................................................... 11
8.0 Service Interval Timer..................................................................... 14
9.0 Copy Functions .................................................................................. 14
10.0 The Information Key........................................................................ 16
11.0 How to Reset The Unit .................................................................... 16
11.1 Reset............................................................................................... 16
11.2 Full reset........................................................................................ 17
12.0 System Wiring Example ................................................................. 18
Installation Instructions
FP735Si
Electronic 3-Channel Full Programmer for
Heating and Hot Water with Service Interval Timer
FP735SI
4
GBGB
Timer Features FP735Si
Power supply 230V ±15%, 50Hz
Memory backup Retained for the life of the product
Factory set calendar clock Automatic summer/winter time change
Switching action of output relay 3 x SPDT, Type 1B
Switch rating of relay contact 3(1) A, 230 VAC
Rated Impulse Voltage 2.5 kV
Dimensions (mm) 140 wide x 91 high x 29 deep
Ball Pressure Test 75°C
Design Standard EN 60730-2-7
Control Pollution Situation Degree 2
Time accuracy ± 1 minute per month
IP rating IP30
Software Classication A
2.0 System Overview
Please Note:
This product should only be installed by a qualied electrician or
competent heating installer and should be in accordance with the
current edition of the IEEE wiring regulations.
1.0 Installation Guide
Danfoss Heating 5
GBGB
3.1 First remove the wallplate from the back of the unit.
3.2 From the top left hand corner of the wallplate, there must be
clearances of at least 21mm to the right, 21mm to the left, 36mm
above and 106mm below in order to mount the plug-in module.
3.3 Wiring
Note: A typical system wiring example is shown on page 18
3.0 Installation
3 on LN
2 on 2 off 1 on 1 off
FP735SI
6
GB
GB
FP735Si is delivered with a set of parameters that have been pre-
programmed to cover the most typical type of installations. See
(5.0). If a dierent parameter setup is wanted the unit provides two
programming options:
4.0 Programming Options
4.1 Normal programming
Normal Programming is meant for setting the timing prole that
controls the ON and OFF periods for the room heating and for the hot
water. A daily prole may be programmed and a prole can control
the entire week where the weekend may be handled separately. Also a
timing prole for a holiday can be entered.
As part of the normal daily operations, a simple one-button press
(+HRS) can extend a running ON period for room heating and/or hot
water by one hour. This can be repeated 3 times giving up to 3 hours
extension.
3.4 Mount the unit on the wallplate
3.5 With the unit powered up, it is recommended to press and
release the RESET button to start up the FP735Si unit.
Note: Always switch
the mains o rst
and never t/remove
the timer to/from a
live wallplate.
Danfoss Heating 7
GB
4.2 Advanced Programming
Advanced Programming is meant for changing certain parameters
that are usually only set once. Advanced Programming can typically
be made by the installer as part of the system installation and setup.
GB
By pressing ADV (advance), the user can jump to the next event in the
daily timing prole. If for instance, the user wants to bring on the room
heating immediately whereas the prole has been programmed to
bring it on in two hours, the user can simply press ADV and the heat
will be turned on.
See the User Guide for normal programming instructions.
FP735SI
8
GB
GB
5.0 Pre-programmed Parameters
FP735Si is delivered with a set of pre-programmed parameters.
5.1 Advanced Programming
The following pre-programmed parameters can be changed in the
Advanced Programming:
Function/parameter Pre-programming
A+B days (disabled, enabled) Disabled
Copy functions
(standard or advanced copy function)
Standard
Summer/winter shift
(automatic or manual)
Automatic
Backlight (always o, always on,
15s after last key press)
15s after last key press
4 events or 6 events per day 6 events
Operating mode
(7 days, 24 hours, 5 + 2 week days)
7 days
Keyboard lock (locked, not locked) Not locked
Service interval (disabled, enabled) Disabled
Note: for the UK market, the FP735Si comes with a default 12 hours clock (AM/
PM) setup.
5.2 Normal Programming
The following pre-programmed parameters can be changed in the
Normal Programming. See User Guide.
Danfoss Heating 9
GB
GB
Event Time Room heating/water heating status
1 06:30 ON
2 08:30 OFF
3 11:30 ON
4 13:30 OFF
5 16:30 ON
6 22:30 OFF
Weekends (Saturday-Sunday):
Event Time Room heating/water heating status
1 07:30 ON
2 09:30 OFF
3 11:30 ON
4 13:30 OFF
5 16:30 ON
6 22:30 OFF
Pre-programmed ON and OFF periods for 4 events per day
Weekdays (Monday-Friday):
Event Time Room heating/water heating status
1 06:30 ON
2 08:30 OFF
3 16:30 ON
4 22:30 OFF
Weekends (Saturday-Sunday):
Event Time Room heating/water heating status
1 07:30 ON
2 09:30 OFF
3 16:30 ON
4 22:30 OFF
Pre-programmed ON and OFF periods for 6 events per day:
Weekdays (Monday-Friday):
FP735SI
10
GB
GB
6.0 Display Information
Channel Status
(Event number when programming)
Channel Number
TIME
Days of Week (Numbers or Text)
KEY TO SYMBOLS
Flame: shows when heating is on
Hourglass: shows during programming delays
Padlock: indicates keyboard is locked
Suitcase: indicates Holiday Mode is set
Clock: Timed Modes
Hand: Manual Modes
Alarm: Indicates alarm is active. Also used for service
due
3 on and 3 o events per day
2 on and 2 o events per day
1 on and 1 o event per day. All Day Mode
Timer (OFF) Mode
+ HRS: Extends function by 1, 2 or 3 hours
Timer (ON) Mode
Otros manuales para FP735Si
3
Tabla de contenidos
Otros manuales de Controladores de temperatura de Danfoss
Danfoss
Danfoss ECL Comfort 210 Manual de usuario
Danfoss
Danfoss 102 Instrucciones de montaje
Danfoss
Danfoss ECL Comfort 310 Manual de usuario
Danfoss
Danfoss ECL Comfort L76 Manual de usuario
Danfoss
Danfoss ECL Comfort 310 Manual de instrucciones de instalación
Danfoss
Danfoss ECL Comfort 210 Manual de usuario
Danfoss
Danfoss ECL Comfort 210 Manual de usuario
Danfoss
Danfoss EKC 361 Manual de usuario
Danfoss
Danfoss Link RS Manual de usuario
Danfoss
Danfoss EKC 101 Manual de usuario
Danfoss
Danfoss RX1 Manual de usuario
Danfoss
Danfoss ECL Comfort 110 Manual de instrucciones
Danfoss
Danfoss ECL Comfort 210 Manual de usuario
Danfoss
Danfoss FHV-A Manual de usuario
Danfoss
Danfoss C17 Instrucciones de montaje
Danfoss
Danfoss MBT 400 Manual de usuario
Danfoss
Danfoss 3060 Instrucciones de montaje
Danfoss
Danfoss FP735Si Manual de usuario
Danfoss
Danfoss MBT 5252 Manual de usuario
Danfoss
Danfoss Optyma Plus OP-MPS Manual de usuario
