Danfoss AKD 2800 Hoja de especificaciones

AKD 2800

■Contents

Quick Setup ....................................................................................................... 3

General warning ..................................................................................................... 3

Mechanical Installation ........................................................................................... 3

Electrical Installation, power ................................................................................... 3

Electrical Installation, control cables ........................................................................ 3

Programming ......................................................................................................... 3

Motor start ............................................................................................................. 4

AKD Lon card ........................................................................................................ 4

Safety regulations ................................................................................................... 4

Warning against unintended start ........................................................................... 5

Introduction to AKD 2800 ........................................................................... 7

Order form ............................................................................................................. 7

High voltage warning .............................................................................................. 9

These rules concern your safety ............................................................................. 9

Warning against unintended start ........................................................................... 9

Control unit ............................................................................................................ 10

Manual initialisation ................................................................................................. 10

Automatic motor tuning .......................................................................................... 11

Programming .................................................................................................... 12

Operation & Display ................................................................................................ 12

Load and Motor ..................................................................................................... 18

References & Limits ................................................................................................ 24

Inputs and outputs ................................................................................................. 28

Special functions .................................................................................................... 34

Serial communication ............................................................................................. 38

Technical functions ................................................................................................. 42

Installation ......................................................................................................... 46

Mechanical dimensions .......................................................................................... 46

Mechanical installation ............................................................................................ 47

General information about electrical installation ...................................................... 48

EMC-correct electrical installation ........................................................................... 49

Electrical installation ............................................................................................... 50

Safety clamp .......................................................................................................... 52

Pre-fuses ................................................................................................................ 52

Mains connection ................................................................................................... 52

Motor connection ................................................................................................... 52

RFI switch .............................................................................................................. 53

Direction of motor rotation ...................................................................................... 53

Parallel connection of motors ................................................................................. 53

Motor cables .......................................................................................................... 53

Motor thermal protection ........................................................................................ 54

Earth connection .................................................................................................... 54

Load sharing .......................................................................................................... 54

Tightening Torque, Power Terminals ....................................................................... 54

Access to control terminals .................................................................................... 54

Electrical installation, control cables ........................................................................ 55

Tightening torques, control cables .......................................................................... 56

MG.28.H2.02 - 1

AKD 2800

Electrical installation, control terminals .................................................................... 56

Relay connection .................................................................................................... 56

Connection examples ............................................................................................. 57

All about AKD 2800 ........................................................................................ 58

Display readout ...................................................................................................... 58

Warnings/alarm messages ..................................................................................... 58

Special conditions .................................................................................................. 62

Aggressive environments ........................................................................................ 62

Galvanic Isolation (PELV) ........................................................................................ 62

EMC emission ........................................................................................................ 64

UL Standard ........................................................................................................... 64

General technical data ............................................................................................ 65

Technical data, mains supply 1 x 220 - 240 V/3 x 200-240 V ................................. 69

Technical data, mains supply 3 x 380 - 480 V ......................................................... 70

Factory Settings ..................................................................................................... 71

MG.28.H2.02 -

AKD 2800

Quick

Setup

■Quick Setup

■General warning

Using this Quick Setup, you can carry out quick and

EMC-correct installation of the frequency converter

in five steps. The Operating Instructions, which are

also enclosed, give other examples of installation

and describe all functions in detail.

Read the safety instructions on the next

page before installing the unit.

■Mechanical Installation

Frequency converters allow side-by-side installation.

Because of the need for cooling, there must be

10 cm free air passage above and below the

frequency converter. Drill holes in accordance with

the measurements given in section Mechanical

dimensions. Retighten all four screws.

Fit the decoupling plate to the power cables and

the earth screw (terminal 95).

■Electrical Installation, power

Please note that the power terminals can be removed.

Connect mains to the mains terminals of the frequency

converter, i.e. 91, 92, 93 and the earth connection to

terminal 95. Fit a screened/armoured cable from the

motor to the motor terminals of the frequency converter,

i.e. U, V, W. The screen ends in a screen connector.

■Electrical Installation, control cables

Remove the front cover underneath the control panel.

Place a jumper between terminals 12 and 27.

■Programming

Carry out programming on the control panel. Press the

[QUICK MENU] key to enter the Quick menu. In this

menu, parameters can be selected by means of the [+]

and [-] keys. The parameter values can be changed by

pressing [CHANGE DATA]. Changes are programmed

using the [+] and [-] keys. Finish the change of a

parameter setting by pressing [CHANGE DATA]. A

change of parameter values is saved automatically after

amainsfailure.Ifthedisplayshowsthreedotsatthe

right, the parameter value has more than three digits.

In order to see the value, activate [CHANGE DATA].

Press [QUICK MENU]: Set the motor parameters

that are on the nameplate of the motor:

Motor power [kW] parameter 102

Motor voltage [V] parameter 103

Motor frequency [Hz] parameter 104

Motor current [A] parameter 105

Rated motor speed parameter 106

Activate AMT:

Automatic motor tuning parameter 107

Set reference range

Min. reference, RefMIN parameter 204

Max. reference, Ref MAX parameter 205

Ramp-up time [s] parameter 207

Ramp-down time [s] parameter 208

In parameter 002 Local/remote control, the frequency

converter mode can be selected as Remote

MG.28.H2.02 - 3

AKD 2800

operation [0], i.e. via the control terminals, or

Local [1], i.e. via the control unit.

Set the control location to Local [1].

Local/remote operation = Local [1] Par. 002

Set the motor speed by adjusting the

Local reference

Local reference Parameter 003

■Motor start

Press [Start] to start the motor. Set the motor speed

by adjusting parameter 003 Local reference.

Check whether the direction of rotation of the motor

shaft is clockwise. If not, exchange any two phases

on the motor cable. Press [STOP/RESET] to stop the

motor. Press [QUICK MENU] to return to display mode.

[QUICK MENU] + [+] keys must be pressed

simultaneously to give access to all parameters.

■AKD Lon card

Requirements:

AKD 2800 must have software version (par

624) 1.32 or higher

AKD 5000 must have software version (par

624) 1.52 or higher

The AKD Lon card is RS485 based and must connect

to an RS485 Adap-Kool Lon network.

The card can be ordered as build-in with the AKD5000

and comes in an external box for the AKD2800.

AKD Lon connections:

The Lon card has two connections.

A 6-pole connector (only 1-4 is used) that connects

to the AKD. Connections are as follows:

AKD-Connections:

Lon card terminals 1

(Red +24V)

(White or Yellow

TX-, RX-)

(Black Com)

(Green TX+, RX+)

AKD terminals 12 69 39 or 20 68

The 3-pole connector for the Lon Communication:

Lon card terminals 1 2 3

Adap-Kool Lon A B Shield

Connect the Adap-Kool Lon network to the removable

3-postion connector. Be careful to route the network

wires away from the AC power and motor wires.

Commissioning

Upon power up the lower red LED of the double LED’s,

next to the Lon connectors will initially be flashing red.

1. Set AKD address in parameter 500 in

the AKD (1 to 60)

2. Wait for about 1 min until the red LED goes

off. (card initialisation)

3. Press one of the service pin buttons

4. Wait for about 2 minutes (upload of

parameters to gateway)

5. Perform a "Net configuration" upload in AKM

and you should now find the AKD. Perform a

"AKC description" upload in AKM

6. Go to menu AKC -> Controllers in AKM and

youshouldfindtheAKD

■Safety regulations

The voltage of the frequency converter

can be fatal whenever it is connected to

mains. Incorrect installation of the motor or

the frequency converter may lead to damage to the

equipment, serious personal injury or death.

Consequently, the provisions of this Quick Setup,

as well as national and local rules and safety

regulations, must be complied with.

Touching the electrical parts may be fatal, even

after the equipment has been disconnected from

mains: wait at least 4 min.

1. The mains supply to the frequency converter must

be disconnected if repair work is to be carried out.

2. The [STOP/RESET] key on the control panel of the

frequency converter does not disconnect the mains

supply and is thus not to be used as a safety switch.

MG.28.H2.02 -

AKD 2800

Quick

Setup

3. Correct protective earthing of the unit must be

established, the user must be protected against

supply voltage, and the motor must be protected

against overload in accordance with applicable

national and local regulations.

4. The earth leakage current is higher than 3.5 mA.

5. Protection against motor overload is not included

in the factory setting. If this function is required,

set parameter 128 Motor thermal protection to

data value ETR Trip or ETR Warning.

6. Check that the mains supply has been disconnected

before removing the motor and mains plugs.

■Warning against unintended start

The motor can be brought to a stop

by means of digital commands, bus

commands, references or local stop,

while the frequency converter is connected to

mains. If personal safety considerations make

it necessary to ensure that no unintended start

occurs, these stops are not sufficient.

While parameters are being programmed, the

motor may start. Consequently, the stop key

[STOP/RESET] must always be activated, following

which data can be modified.

A motor that has been stopped may start if faults

occur in the electronics of the frequency converter, or

if a temporary overload, a fault in the supply mains

or a fault in the motor connection ceases.

MG.28.H2.02 - 5

AKD 2800

AKD 2803-2815 200-240 V

AKD 2805-2815 380-480 V

AKD 2822 200-240 V

AKD 2822-2840 380-480 V

AKD 2840 200-240 V

AKD 2855-2875 380-480 V

AKD 2880-2882 380-480 V

MG.28.H2.02 -

AKD 2800

Introduction to AKD

2800

MG.28.H2.02 - 7

AKD 2800

195NA299.11

AKD 2800

Operating instructions

Software version: 1.3x

These operating instructions can be used for all series fre-

quency converters with software version 1.3x.

The software version number can be seen from parameter

640 Software version no.

NB!:

Indicates something to be noted by the reader.

Indicates a general warning.

Indicates a high-voltage warning.

MG.28.H2.02 -

AKD 2800

Introduction to AKD

2800

■High voltage warning

The voltage of the frequency converter

is dangerous whenever the converter is

connected to mains. Incorrect fitting of the

motor or frequency converter may cause damage to the

equipment, serious injury or death. Consequently, it is

essential to comply with the instructions in this manual

as well as local and national rules and safety regulations.

■These rules concern your safety

1. The frequency converter must be disconnected

from the mains if repair work is to be carried

out. Check that the mains supply has been

disconnected and that the prescribed time has

passed before removing motor and mains plugs.

2. The [STOP/RESET] key on the control panel of

the frequency converter does not disconnect

the equipment from mains and is thus not to

be used as a safety switch.

3. The unit must be properly connected to the

earth, the user must be protected against the

supply voltage and the motor must be protected

against overloading pursuant to prevailing

national and local regulations.

4. The earth leakage currents are higher than 3.5 mA.

5. Protection against motor overload is not included

in the factory setting. If this function is required,

set parameter 128 Motor thermal protection to

data value ETR trip or data value ETR warning.Fo

the North American market: The ETR functions

provide overload protection of the motor, class

20, in accordance with NEC.

6. Do not remove the plugs for the motor - and mains

supply while the frequency converter is connected

to mains. Check that the mains supply has been

disconnected and that the prescribed time has

passed before removing motor and mains plugs.

7. Note that the frequency converter has more voltage

inputs than L1, L2 and L3 when the DC bus

terminals are used. Check that all voltage inputs

are disconnected and that the prescribed time has

passed before repair work is commenced.

■Warning against unintended start

1. The motor can be brought to a stop by means

of digital commands, bus commands, references

or a local stop, while the frequency converter

is connected to mains. If personal safety

considerations make it necessary to ensure

that no unintended start occurs, these stop

functions are not sufficient.

2. While parameters are being changed, the

motor may start. Consequently, the stop key

[STOP/RESET] must always be activated, following

which data can be modified.

3. A motor that has been stopped may start if faults

occur in the electronics of the frequency converter,

or if a temporary overload or a fault in the supply

mains or the motor connection ceases.

195NA300.10

Warning:

It can be extremely dangerous to touch the electrical parts

even when the mains supply has been disconnected.

Also ensure that other voltage inputs are disconnected

from load sharing through the DC bus.

Wait at least 4 minutes after the input power has been

removed before servicing the drive.

MG.28.H2.02 - 9

AKD 2800

■Control unit

On the front of the frequency converter there

is a control panel.

The control panel is divided into four function groups:

1. Six-digit LED display.

2. Keys for changing parameters and shifting

display function.

3. Indicator lamps.

4. Keys for local operation.

All displays of data are in the form of a six-digit LED

display capable of showing one item of operating

data continuously during normal operation. As a

supplement to the display, there are three indicator

lamps for indication of mains connection (ON),

warning (WARNING) and alarm (ALARM). Most of

the frequency converter’s parameter Setups can be

changed immediately via the control panel, unless

this function has been programmed as Locked [1]

via parameter 018 Lock for data changes.

■Control keys

[QUICK MENU] allows access to the parameters

used for the Quick menu.

The[QUICKMENU]keyisalsousedifachangetoa

parameter value is not to be implemented.

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador