Danfoss AK-CC 550A Manual de instrucciones

Troubleshooting Guidelines

AK-CC 550A

Service Guide

ADAP-KOOL® Refrigeration Control System

Service Guide |Troubleshooting Guidelines, AK-CC 550A

2 | AX278927426184en-000101

The following troubleshooting guidelines detail the process of

verifying proper setup of an AK-CC 550A when encountering

communication/oﬄine issues with an AK-SM 800 series controller.

System Manager Programming

• Complete Rescan

- On Network Nodes screen, select ‘Press for complete rescan’

*Also complete rescan if any of the items below required

adjustment

• Ensure proper channel enabled on Network Nodes screen of

system manager

- ‘Channel LONWORKS’ for LON RS485 comm loop

- ‘Channel MODBUS-RS485’for Modbus comm loop

• Verify no Duplicates in System Manager

- Check under Network Nodes->Duplicates

- If duplicates exist, identify case controller with mistaken

address, and update

• Verify address has been assigned to case controller in

program

- Verify under Conﬁguration->Control->Refrigeration-

>Addresses

AK-CC 550A Hardware

• Verify part # of AK-CC 550A. This will be printed on front of

controller below display

- For 084B8030, verify 230Vac to terminals 1&2

- For 084B8036, verify 115Vac to terminals 1&2

AK-CC 550A Programming

• Ensure address is set correctly, via parameter o03.

• Ensure application is set correctly, via parameter o61.

Comm Loop Wiring

• Verify intended form of communication to be used (Modbus

or LON RS485)

- For Modbus communication:

- Ensure comm wires are landed on terminals 57&58.

- Modbus loop is polarity sensitive, ensure polarity is

consistent throughout loop

- Ensure any other Modbus devices on the loop use 38400

baud rate

- For LON RS485 communication:

- Ensure comm wires are landed on terminals 52&53

- Ensure EKA 175 comm card is installed in port below

display.

- EOL resistor

- For 1 loop from system manager, ensure 120 ohm resistor

at end of loop and switch above comm plug in ‘On’

position

- For 2 loops from system manager, ensure 120 ohm resistor

at end of each loop and switch above comm plug in ‘Oﬀ’

position

• For either comm type, max distance is 4000’. Beyond this

distance, a repeater is needed

• For either comm type, max # of case controllers is 120 per

system manager

• For either comm type, an EIA 485 rated cable should be used

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.

Otros manuales para AK-CC 550A

Otros manuales de Unidad de control de Danfoss

Danfoss

Danfoss MNF Series Manual de usuario

Danfoss

Danfoss SVA-S Manual de usuario

Danfoss

Danfoss PM3 Instrucciones de funcionamiento y mantenimiento

Danfoss

Danfoss MSV-F2 DN15 - 400 Manual de usuario

Danfoss

Danfoss Akva Lux II TDP-F Manual de usuario

Danfoss

Danfoss SVA-S 6-10 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss SFA 10 Manual

Danfoss

Danfoss VLT Safety Option MCB 150 Manual de usuario

Danfoss

Danfoss MSV-C Manual de usuario

Danfoss

Danfoss PVG 16 PVH/Covers Manual

Danfoss

Danfoss ICV PM 25 Manual de usuario

Danfoss

Danfoss ICF 15 Manual de usuario

Danfoss

Danfoss SFV Series Manual de usuario

Danfoss

Danfoss ICSH 25 Manual de usuario

Danfoss

Danfoss EVR 2 Manual de usuario

Danfoss

Danfoss EV250B NC Manual de instrucciones de instalación

Danfoss

Danfoss SVA-S Manual de usuario

Danfoss

Danfoss PVEO Manual de usuario

Danfoss

Danfoss MSV-F2 DN Series Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss ChangeOver6 Manual de usuario

Danfoss

Danfoss VMV 15 Manual de usuario

Danfoss

Danfoss PVG 120 Manual

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario