Dahua Technology 50430UN Manual de usuario

4 MP PTZ Network Camera

50430UN

59430UN

Quick Start Guide

Version 001.001

Dahua Technology USA Inc.

Table of Co te ts
1 Welcome..........................................................................................................................1
1.1 Important Safeguards and Warnings..................................................................1
Electrical safety...................................................................................................1
En ironmental Precautions.................................................................................2
Operation and Daily Maintenance......................................................................3
Warnings.............................................................................................................3
1.2 FCC Information..................................................................................................4
FCC compliance：..............................................................................................4
1.3 Legal Notices......................................................................................................4
Copyright.............................................................................................................4
Trademarks.........................................................................................................4
1.4 Disclaimer...........................................................................................................5
2 Unpacking........................................................................................................................6
3 Installation and Configuration..........................................................................................7
3.1 Camera Configuration and Cables.....................................................................7
3.2 Framework and Dimensions...............................................................................8
3.3 Alarm Setup........................................................................................................8
Alarm Input..........................................................................................................8
Alarm Output – Le el Application.......................................................................9
Alarm Output – Switch Application.....................................................................9
3.4 Locally Storing Data..........................................................................................10
4 De ice Installation.........................................................................................................11
4.1 Installing the Camera........................................................................................11
5 Network Configuration...................................................................................................14
5.1 Network Protocols.............................................................................................14
5.2 Modifying the IP Address..................................................................................15
5.3 Using the ConfigTool........................................................................................15
5.4 Accessing the Web Interface............................................................................16
5.5 Configuring Alarms...........................................................................................17
5.6 Configuring Local SD Card Recording.............................................................17

1 Welcome

This manual offers reference material and general information about the basic operation,

maintenance, and troubleshooting of the Dahua Multi-Sensor Panoramic Camera. Read, follow, and

retain the following safety instructions. Heed all warning on the unit and in the operating instructions

before operating the unit. Keep this guide for future reference.

1.1 Importa t Safeguards a d War i gs

Electrical safety

Install the unit in accordance with the manufacturer’s instructions and in accordance with

applicable local codes.

All installation and operation must conform to your local electrical safety codes.

Do not o erload outlets and extension cords, which may cause fire or electrical shock.

Do not place the camera near or in a place where the camera may contact o erhead power

lines, power circuits, or electrical lights.

Ensure power conforms to SELV (Safety Extra Low Voltage) and that the limited power source is

rated AC 24V as specified in IEC60950-1. (Power supply requirement is subject to the de ice

label).

All input/output ports are SELV circuits. Ensure that SELV circuits are connected only to other

SELV circuits.

Ground the unit using the ground connection of the power supply to protect the unit from

damage, especially in damp en ironments.

Protect the plug and power cord from foot traffic, being pinched, and its exit from the unit.

Units with or without an ON/OFF switch ha e power supplied to the unit whene er the power

cord is inserted into the power source; howe er, the unit is operational only when the ON/OFF

switch is in the ON position. The power cord is the main power disconnect de ice for switching

off the oltage for all units.

Operate the unit only from the type of power source indicated on the label. Before proceeding,

disconnect the power from the cable to be installed into the unit.

For external power supplied units, use only the recommended or appro ed power supplies.

Limited power sources must comply with EN 60950. Substitutions may damage the unit or

cause fire or shock.

For 24 VAC units, oltage applied to the unit’s input power should not exceed ±25%. User-

supplied wiring must comply with local codes (Class 2 power le els). Do not ground the

supply at the terminals or at the unit’s power supply terminal.

Contact the local dealer or the power company to erify the correct power supply.

Do not supply power ia the Ethernet connection (PoE) when power is already supplied ia the

power connector.

Do not attempt to ser ice the unit. Opening or remo ing co ers may expose you to dangerous

oltage or other hazards. Refer all ser icing to qualified personnel.

If the unit is damaged and requires ser ice, unplug the unit from the main AC power supply and

from the PoE supply and refer to qualified ser ice personnel. Damage may include, but is not

limited to:

The power supply cord or plug is damaged.

Liquid has spilled in or on the unit.

An object has fallen on the unit.

The unit has been dropped and the housing is damaged.

The unit displays a marked change in performance.

The unit does not operate in the expected manner when the user correctly follows the proper

operating procedures.

Ensure a ser ice technician uses replacement parts specified by the manufacturer, or that ha e

the same characteristics as the original parts. Unauthorized parts may cause fire, electrical

shock, or other hazards. Dahua is not liable for any damage or harm caused by unauthorized

modifications or repairs.

Perform safety checks after completion of ser ice or repairs to the unit.

Use attachments and accessories only specified by the manufacturer. Any change or

modification of the equipment, not expressly appro ed by Dahua, could oid the warranty.

Incorporate a readily accessible disconnect de ice in the building installation wiring for quick

power disconnect to the camera.

Dahua assumes no liability or responsibility for any fire or electrical shock caused by improper

handling or installation.

E viro me tal Precautio s

Do not aim the unit at a strong light source or into direct sunlight to focus. A strong light source

may cause o erexposure and may affect the longe ity of the CCD or the CMOS sensor.

Transport, use, and store the unit within the specified temperature and humidity range.

Do not place the unit in a wet, dusty, extremely hot or an extremely cold en ironment; and a oid

en ironments with strong electromagnetic radiation or unstable lighting.

Ne er push objects of any kind into this unit through openings as they may touch dangerous

oltage points or cause a short circuit that may result in fire or electrical shock. Take care to not

spill any liquid on the unit.

Do not use units intended for indoor applications near water, in damp or wet en ironments, or in

any area classified as a wet location. Do not expose an indoor unit to rain or moisture to reduce

the risk of fire or electric shock.

Do not block or co er any openings in the unit enclosure. These openings are pro ided for

entilation to pre ent o erheating and to ensure reliable operation. Ensure the unit is placed in

an area with adequate entilation.

Do not place the unit near a heat source such as heaters, sto es, radiators or other equipment

that produces heat.

Pack the unit with standard factory packaging or material of the same quality when transporting

the unit.

Take care to a oid hea y stress, iolent ibration, or water spills to the camera unit during

transportation, storage, and installation.

Operatio a d Daily Mai te a ce

Do not touch the heat dissipation component of the unit. This part of the unit is hot and may

cause a burn.

Do not open or dismantle the de ice; there are no components that a user can fix or replace.

Opening the unit may cause water leakage or expose components to direct light. Contact the

manufacturer or a qualified ser ice representati e to ser ice the camera or to replace a

component, including the desiccant.

Dahua recommends the use of a thunder-proof de ice in concert with the unit.

Do not touch the CCD or the CMOS optic sensor. Use a blower to clean dust or dirt on the lens

surface. Use a dry cloth dampened with alcohol and gently wipe away any dust on the lens.

Use a dry soft cloth to clean the unit’s housing. If the unit is particularly dusty, use water to dilute

a mild detergent, apply the diluted detergent to a soft cloth, then gently clean the de ice. Finally,

use a dry cloth to wipe the unit dry. Do not use a olatile sol ent like alcohol, benzene, or

thinner; or use a strong detergent with abrasi es, which may damage the surface coating or

reduce the working performance of the unit.

Do not touch or wipe a dome co er during installation, this co er is an optical de ice. Refer to

the following methods clean the dome co er:

Stained with dirt: Use an oil-free soft brush or blower to gently remo e the dirt.

Stained with grease or fingerprints: Use a soft cloth to wipe gently the water droplet or the oil

from the dome co er. Then, use an oil-free cotton cloth or paper soaked with alcohol or

detergent to clean the lens from the center of the dome to outside. Change the cloth se eral

times to ensure the dome co er is clean.

Lifti g Applia ce Requireme t

Select the proper PTZ dome installation mode and use the proper lifting de ice to safely lift the

camera at the installation site.

Ensure that the lifting de ice has the proper capacity to reach the installation height.

Use the lifting de ice in accordance with its operating instructions and abide by the de ice’s

safety precautions.

War i gs

Change the default password after the initial login to protect the integrity of the network.

Use the standard accessories pro ided by the manufacturer and ensure the unit is installed and

commissioned by qualified professionals.

Protect the lens area from laser radiation when using a laser de ice to aid in installation and

le eling of the unit.

Do not supply power ia the Ethernet connection (PoE) when power is already supplied ia the

power connector.

1.2 FCC I formatio

This de ice complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

This de ice may not cause harmful interference;

This de ice must accept any interference recei ed, including interference that may cause

undesired operation.

FCC complia ce：

This equipment has been tested and found to comply with the limits for a digital de ice, pursuant to

part 15 of the FCC Rules. These limits are designed to pro ide reasonable protection against harmful

interference. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio

communication. Howe er, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or tele ision reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the recei ing antenna.

Increase the separation between the equipment and recei er.

Connect the equipment into an outlet on a circuit different from that to which the recei er is

connected.

Consult the dealer or an experienced radio/TV technician for help.

1.3 Legal Notices

This user guide is the intellectual property of Dahua Technology Company, LTD and is protected by

Trademarks

All hardware and software product names used in this document are likely to be registered

trademarks and must be treated accordingly.

1.4 Disclaimer

This user guide has been compiled with great care and the information it contains has been

thoroughly re iewed and erified. The text was complete and correct at the time of printing. This

guide may be periodically updated to reflect changes to the product or to correct pre ious

information and the content of this guide can change without notice. If you encounter an error or

ha e any questions regarding the contents of this guide, contact customer ser ice for the latest

documentation and supplementary information. Dahua accepts no liability for damage resulting

directly or indirectly from faults, incompleteness, or discrepancies between this guide and the

product described. Dahua is not liable for any loss caused by installation, operation, or

maintenance inconsistent with the information in this guide.

Video loss is inherent to all digital sur eillance and recording de ices; therefore Dahua cannot be

held liable for any damage that results from missing ideo information. To minimize the

occurrence of lost digital information, Dahua recommends multiple, redundant recording

systems, and adoption of backup procedure for all data.

Contact the supplier or customer ser ice if you encounter any issue while using this unit.

2 U packi g

This equipment should be unpacked and handled with care. If an item appears to ha e sustained

damage during shipping, notify the shipper immediately.

Verify that all the parts listed below are included. If an item is missing, contact customer support or

your local representati e.

The original packing carton is the safest container to transport the unit, in the e ent the unit must be

returned for ser ice. Retain the carton and all shipping material for future use.

Please refer to the enclosed CD for more details, to iew the detailed User’s Manual, and for

configuration software.

2.1 Parts List

Package Item

Quantity

Network PTZ Camera

Quality Tag

Pair of Glo es

Installation Hardware Pack

Expansion Bolts

Screws

Hex Key

Wall Mount Accessory Kit

Wall Mount Adapter

24 VAC Power Supply

Quick Start Guide

Documentation CD

2.2 Tools a d Hardware Required

Package Item

Quantity

Screwdri er

Expansion Bolts (size?)

Hex Bolts (size?)

Screws?

3 I stallatio a d Co figuratio

3.1 Framework a d Dime sio s

The following figures show the dimensions of the de ice in mm (in.). These images are intended

as a reference only.

Figure 3-1: Dime sio s for 50430UN

Figure 3-2: Dime sio s for 59430UN

3.2 Wiri g

The dome camera includes the following wiring bundles:

Wire Color Co ectio

Power Red 24 VAC

Yellow/Green Earth Ground

Black 24 VAC

Video/Co trol Black RJ-45 Ethernet

Alarm Red Alarm IN 1

Brown Alarm IN 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Dahua Technology

Dahua Technology

Dahua Technology IPC-HDW1531SP Manual de usuario

Dahua Technology

Dahua Technology Eyeball Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW5842T-ZE Manual de usuario

Dahua Technology

Dahua Technology D-IPC-HDBW3841EP-S-0280-S2 Manual de usuario

Dahua Technology

Dahua Technology 59230UNI Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HDW3441TP-ZS-S2 Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW3549H-ZAS-PV-27135 Manual de usuario

Dahua Technology

Dahua Technology D-IPC-HUM8441-E1-L1 Manual de usuario

Dahua Technology

Dahua Technology Lite IPCHFW2231T-ZAS-S2 Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW2431T-ZS Manual de usuario

Dahua Technology

Dahua Technology N68BR4 Manual de usuario

Dahua Technology

Dahua Technology IPC-HDBW1531E-S-0280B Manual de usuario

Dahua Technology

Dahua Technology IPC-HUM8531M-V-LED-0360B Manual de usuario

Dahua Technology

Dahua Technology A42AR2 Manual de usuario

Dahua Technology

Dahua Technology D-SDZ4032-HNR-ZB Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW2431T-AS-S2 Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HFW4X-W Manual de usuario

Dahua Technology

Dahua Technology ANPR Manual de usuario

Dahua Technology

Dahua Technology EZ-IP BULLET Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HDBW3466FP-AS-AUS Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HFW3849T1P-AS-PV-S3-BLK Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-PFW8601N-H-A180 Manual de usuario

Dahua Technology

Dahua Technology DSS4004-S2 Instrucciones generales

Dahua Technology

Dahua Technology D-IPC-HDBW1430DEP-SW-0280B Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario