Dahle 20390 Manual de usuario
390 SERIES
HIGH CAPACITY SHREDDERS
20390
20394
20396
OPERATION MANUAL
20390.90.1830 - 09/2007
2
Congratulations on your purchase of a DAH E High Capacity Shredder! We here
at DAH E North America are dedicated to providing rugged and dependable
products for the large, and not so large office. We are sure your new DAH E High
Capacity Shredder will meet or exceed your expectations of quality and service.
If you have any questions regarding your new DAH E High Capacity shredder, call
your sales representative, or call DAH E Customer Service, toll free, at (800) 995-
1379 between 8:30 am and 5:00 pm Monday through Friday, EST.
Check off the model and record the serial number for your records in the space
provided below.
Serial Number:________________________
DIAGRAM KEY
1. Main Plug
1.1 Main Switch
2. Feed Opening
3. ight Barrier
4. Bag Full Indicator
5. Door Ajar Indicator
6. Paper Jam Indicator
7. Forward Switch (electronic models)
7a. Reverse Switch (electronic models)
8. Power Switch (electronic models)
9. Waste Bin
10. Door Handle
11. Door
20390 20394 20396
READ A INSTRUCTIONS BEFORE OPERATING YOUR SHREDDER
3
A WAYS TURN SHREDDER OFF IF IT WI BE UNATTENDED FOR ONG PERIODS OF TIME
SAFETY INSTRUCTIONS
Read the operating instructions carefully proir to starting up the unit!
Do not use in the vicinity of flammable liquids or gases.
Do not use in the vicinity of corrosive materials.
Do not expose to the wet.
Do not let children operate this office equipment.
Do not reach into the cutting mechanism during operation.
Do not use the shredder over a period of more than 5 minutes in no-load
operation (operation without paper).
Keep long hair clear of machine.
Keep neck-ties clear of machine.
Keep bracelets clear of machine.
Power supply must be accessible all the times.
Disconnect power supply before servicing.
The safety devices must not be manipulated with or removed.
Please make sure that the shredder gets sufficient ventilation (ventilating
flaps must kept free).
Product is not intended for use by children.
IMPORTANT - Model 20394: Do NOT shred staples and paperclips.
BEFORE YOU SHRED
Remove Transport Bolts with wrench provided.
Record the Model and Serial Number in the space provided inside the front
cover.
Be sure the electrical outlet provides the proper power for your shredder (see
rating label on rear of shredder).
Install Shred Bag (see: “CHANGING THE SHRED BAG”).
TURNING ON YOUR SHREDDER
1. ON/OFF is controlled by the main switch (1.1) and
green push button (8) found on top of the shredder.
2. Pressing these buttons (main switch 1.1 first) turns
the shredder on and places it in the stand-by mode.
3. Pressing these buttons again turns the
shredder off.
SHREDDING
Turn shredder on. Insert paper squarely into
Feed Opening (3). A light barrier will auto-
matically activate the shredding mechanism.
Continue feeding paper into the Feed Opening
until the shredding mechanism begins to
draw the paper in. At this point, allow the paper
to feed into the shredder on its own. Once the
paper has passed completely through the shredding mechanism, the electronic
controls will automatically stop the machine.
To shred a piece of paper too small to break the light barrier, press the FORWARD
button (7) once to override the auto ON/OFF function. The shredder will continue
to run until the FORWARD button (7) is pressed again.
Microfiche and transparecies can also be shredded in the same manner as paper,
however, you should shred a piece of paper after every 8 or 10 sheets of plastic.
This helps clean plastic particles out of the shredding mechanism.
CAPACITY
Capacity is the number of sheets of 81/2”x 11” paper that can be shredded at one
time. These figures are approximate and machines may vary slightly due to various
conditions. It is not recommended that you try to run your shredder at maximum
capacity, as this increases the chance of a paper jam.
Model 20 L . Bond 16 L . Bond
20390 55 60
20394 8 10
20396 38 43
CCLLEEAARRIINNGG AA PPAAPPEERR JJAAMM
If too many sheets of paper are fed into your shredder at one time, it may cause a
paper jam. Running your shredder at maximum capacity increases the chance of a
paper jam. If a paper jam occurs, it is easy to clear by following these simple steps:
The Auto-Reverse feature, built into the electronic versions of DAH E High Capacity
Shredders, helps prevent paper jams. If the Auto-Reverse feature is activated an
audible alarm sounds and the paper Jam Indicator (6) lights up. If this situation
occurs, follow these simple steps:
4
A WAYS TURN SHREDDER OFF IF IT WI BE UNATTENDED FOR ONG PERIODS OF TIME
5
1. Remove paper from Feed Opening. The REVERSE button (7a) may be used if
excess paper remains in the Feed Opening (not on Model 20394). Clear
shredding mechanism by pressing the FORWARD button (7).
2. Separate some of the sheets and continue shredding.
20394
1. In case of a paper jam the shredder runs backwards for 0,5 sec.
2. Remove paper from feed opening. Clear shredding mechanism by pressing the
FORWARD button (7). The REVERSE button (7a) is locked until the FORWARD
button (7) has been pressed.
3. Separate some of the sheets and continue shredding.
CHANGING THE SHRED BAG
When the Shred Bag is full, the shredder will automatically shut down. On the elec-
tronic models an ED indicator will light and an audible alarm will sound. Changing the
Shred Bag is quick and easy if you follow these simple directions.
1. Turn shredder off
2. Open Door (11) using Door Handle (10) to expose Waste Bin (9) and Shred Bag.
3. Slide Waste Bin and full Shred Bag from shredder.
4. Dispose of full Shred Bag.
5. Install new Shred Bag in Waste Bin, draping end of Shred Bag over the lip of
the Waste Bin.
6. Slide Waste Bin, with new Shred Bag installed, back into shredder.
7. Close Door.
8. Turn on shredder and continue shredding.
CARING FOR YOUR SHREDDER
Clean covers with a clean dry cloth. Do not use water or solvents. Make sure you
disconnect your shredder from its power source before cleaning.
Paper shredders, like all mechanical equipment, need proper maintenance to ensu-
re efficient operation. Periodic lubrication of the cutting blades is important to offset
the friction generated within the cutting head. Frequency of lubrication will vary
depending on the shred size and the amount of usage. A strip-cut shredder recei-
ving light use (1 – 2 hours per week) will require lubrication only once or twice a
month, while the same machine used 1 – 2 hours per day will require lubrication
weekly. A cross-cut shredder should be lubricated every 1/2hour of shredding time
to maintain maximum capacity and efficiency.The procedure for lubricating your
shredder is simple, and can be performed by any operator. The oil is packaged in a
squeeze bottle and is applied directly to the cutting blades through the feed opening
(3). Run a fine stream of lubricant from one side of the feed opening to the other.
Run the shredder in REVERSE for a few seconds to help distribute the lubricant
evenly. You can now continue shredding as usual.
NOTE: SHREDDER WI NOT OPERATE UN ESS DOOR IS COMP ETE Y C OSED
6
DAH E Shredder Oil is the only lubricant you should use in your paper shredder.
It has been specially formulated so as not to leave any residue that could attract
dust and clog the shredding mechanism. You can order DAH E Shredder Oil from
your local dealer.
Repairs on your paper shredder should only be performed by qualified
technicians. If you need service, contact your local dealer, or you can contact
DAH E North America Customer Service between 8:30 am and 5:00 pm EST at
(800) 995-1379.
BEFORE YOU CALL FOR SERVICE
A WAYS TURN SHREDDER OFF IF IT WI BE UNATTENDED FOR ONG PERIODS OF TIME
1. Power buttons not
pressed
2. Unit unplugged
3. Outlet dead
4. Door not fully closed
5. Shred Bag full
1. Cutting blades dry
Press buttons (green
light turns on)
Connect to outlet
Reset circuit breaker
Close Door
Change Shred Bag
ubricate cutting blades
according to instructions.
SYMPTOM POSSIBLE CAUSES SOLUTION
No Power
ow capacity
7
IF ANY OTHER PROB EMS OCCUR. CA YOUR AUTHORIZED DAH E SERVICE DEA ER
DAHLE SHREDDER SUPPLIES AND ACCESSORIES
Shred Bags (100 per box)
Item No. Models
701 Personal & 20300 Series
704 20400, 20500 & 20600 Series
705 20800 Series
706 High Capacity Models
Waste Bin
739 2039X Series
Shredder Oil (All Models)
740 Box of 4 16oz. Bottles
740G Box of 4 1gal Bottles
Automatic Oiling System
SAO-110 1.5 iter Auto Oiler
SAO-120 4 iter Auto Oiler
Dahle North America, Inc.
49 Vose Farm Road
Peterborough, New Hampshire 03458
Tel: (603) 924-0003 • Fax: (603) 924-1616
Email: [email protected]
www.dahle.com
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Trituradora de papel de Dahle
Dahle
Dahle 707 PS Manual de usuario
Dahle
Dahle Dahle 20304 ES Manual de usuario
Dahle
Dahle 828 HD Manual de usuario
Dahle
Dahle Dahle 20100 PS Manual de usuario
Dahle
Dahle Dahle 20404 Manual de usuario
Dahle
Dahle ShredMATIC 35120 Manual de usuario
Dahle
Dahle 828 HD Manual de usuario
Dahle
Dahle PaperSAFE 260 Manual de usuario
Dahle
Dahle ShredMATIC 35150 Manual de usuario
Dahle
Dahle 114 air Manual de usuario
Dahle
Dahle 20390 Manual de usuario
Dahle
Dahle 707 PS Manual de usuario
Dahle
Dahle Dahle 30304 Manual de usuario
Dahle
Dahle 818 HD Manual de usuario
Dahle
Dahle 20606 EC Manual de usuario
Dahle
Dahle Dahle 20304 ES Manual de usuario
Dahle
Dahle 30404 Manual de usuario
Dahle
Dahle 909 HS Manual de usuario
Dahle
Dahle PaperSAFE Manual de usuario
Dahle
Dahle ShredMATIC 90 Manual de usuario
Manuales populares de Trituradora de papel de otras marcas
Swingline
Swingline STACK-AND-SHRED200X&200XL 60X Manual de instrucciones
GBC
GBC ShredMaster CC055 Manual de usuario
UNITED OFFICE
UNITED OFFICE UAV 190 A1 Manual de usuario
UNITED OFFICE
UNITED OFFICE UAV 190 A1 Manual de usuario
Rexel
Rexel Optimum AutoFeed+ 45X Manual de usuario
Martin Yale
Martin Yale 227284S1 Manual de usuario
