DAB GENIX VT Manual de operación y mantenimiento

INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE

GENIX VT

ENGLISH AUS

INDEX

Key ........................................................................................................... 2

Warnings .................................................................................................. 2

Responsibility ...........................................................................................3

General description ..................................................................................3

1. Applications .........................................................................................3

2. Pumped liquids....................................................................................3

3. Installation ...........................................................................................3

4. Electrical connection ...........................................................................4

5. Accessories .........................................................................................4

6. Maintenance........................................................................................4

6.1 Adjustment of run time..................................................................4

6.2 Maintenance instructions..............................................................4

7. Technical data .....................................................................................5

8. Management .......................................................................................5

8.1 Storage.........................................................................................5

8.2 Transport ......................................................................................6

8.3 Weight ..........................................................................................6

9. Modications and spare parts .............................................................6

10. Disposal .............................................................................................6

11. Troubleshooting .................................................................................7

KEY

The following symbols have been used in the discussion:

SITUATION OF GENERAL DANGER.

Failure to respect the instructions that follow may cause harm to

persons and property.

WARNINGS

Read this documentation carefully before installation.

Installation and operation must comply with the local safety reg-

ulations in force in the country in which the product is installed.

Everything must be done in a workmanlike manner.

Failure to respect the safety regulations not only causes risk to

personal safety and damage to the equipment, but invalidates

every right to assistance under guarantee.

Skilled personnel

It is advisable that installation be carried out by competent, skilled

personnel in possession of the technical qualications required by

the specic legislation in force.

The term skilled personnel means persons whose training, experi-

ence and instruction, as well as their knowledge of the respective

standards and requirements for accident prevention and working

conditions, have been approved by the person in charge of plant

safety, authorizing them to perform all the necessary activities,

during which they are able to recognize and avoid all dangers.

(Denition for technical personnel IEC 364)

The appliance may be used by children over 8 years old and by

persons with reduced physical, sensory or mental capacities, or

who lack experience or knowledge, on condition that they are

under supervision or after they have received instructions con-

cerning the safe use of the appliance and the understanding of

the dangers involved. Children must not play with the appliance.

Cleaning and maintenance intended to be carried out by the user

must not be performed by children without supervision.

ENGLISH

AUS

Safety

Use is allowed only if the electric system is in possession of safe-

ty precautions in accordance with the regulations in force in the

country where the product is installed.(for Italy CEI 64/2)

The power supply cable must never be used to carry or shift the

pump.

Never pull on the cable to detach the plug from the socket.

If the power cable is damaged, it must be replaced by the manu-

facturer or by their authorised technical assistance service, so as

to avoid any risk.

Failure to observe the warnings may create situations of risk for persons or

property and will void the product guarantee.

RESPONSIBILITY

The Manufacturer does not vouch for correct operation of

the electropumps or answer for any damage that they may

cause if they have been tampered with, modied and/or run

outside the recommended work range or in contrast with

other indications given in this manual.

The Manufacturer declines all responsibility for possible er-

rors in this instructions manual, if due to misprints or errors

in copying. The Manufacturer reserves the right to make any

modications to products that it may consider necessary or

useful, without a󰀨ecting their essential characteristics

GENERAL DESCRIPTION

Genix VT systems are compact small automatic lifting stations, suitable for

pumping domestic waste water, where evacuation by gravity is not possi-

ble.

The utilities connected to this system can be used normally and require

minimum maintenance.

The system will operate automatically as soon as the required level of

water enters the tank.

1. APPLICATIONS

Genix systems are indicated exclusively for the treatment of domestic

waste water from sinks, bathtubs, showers, or from washing machines

and dishwashers.

The product must be fastened to the oor to prevent uplift and turning.

2. PUMPED LIQUIDS

The product is only suitable for pumping wastewater from a cab-

inet shower, bidet and dishwashers. Not for heavy-duty public,

commercial or industrial use, and only for a limited number of

users.

Any damage due to foreign bodies (wet wipes, food, cotton wool,

tampons, hair, cotton cloths, wood, metal or plastic objects) or

due to pumping liquids such as solvents, strong chemical agents

and oil will not be covered by the guarantee.

Ordinary liquids for cleaning of the appliances connected. pH val-

ue: 4-10.

Maximum using temperature 90°C (for 30 min)

The product is sized for a maximum volume of 10 l litres and a

maximum inlet of 130 l/min.

3. INSTALLATION

The system must never be lifted by its power cable to carry it.

The product must be accessible for maintenance and repair.

The product must be placed in a frost-free room to prevent the

pumped liquid from freezing.

Make sure that all external pipework is adequately insulated.The

discharge pipe must be made of rigid material, such as copper,

or of rigid PVC with solvent-welded joints.To prevent the trans-

mission of vibrations to buildings, make sure that the pipework

is thoroughly xed and that ttings cannot move and are not in

contact with building parts.

ENGLISH AUS

Make sure to a󰀩x the “WaterMark” and “Prohibited items” stickers

in a clearly visible location on the device.

Installation in accordance with Plumbing Code of Australia

and AS/NZS3500.

4. ELECTRICAL CONNECTION

Make sure that the product is suitable for the supply voltage and

frequency available at the installation site.The electrical connec-

tion must be carried out in accordance with local regulations.

The product must be earthed.

The installation must include an earth leakage circuit breaker for

protection against earth fault currents. Thisensures protection

when using a Schuko plug or another plug with earth pin.The

product must be connected to a mains switch with a minimum

contact gap of 3 mm in all poles.In case of overtemperature, a

thermal switch cuts out the motor and cuts it in automatically when

it has cooled su󰀩ciently.

5. ACCESSORIES

1- An alarm device for acoustic alarm in case of malfunction or high level

in the tank is available as an accessory (noise level 75 dB(A)). Product

number: 60166477.

2- A kit containing: a hose (length 500mm) with adapter, available as an

accessory. Product code 60168126

1 2

6. MAINTENANCE

The system does not require any particular maintenance, but we recom-

mend checking the operation and couplings of the pipes at least once a

year.

6.1 Adjustment of run time

The default setting ensures proper operation in most pipework. If the pipe-

work is particularly long or short, it may be necessary to adjust the run

time.

6.2 Service instructions

Thanks to the product design, service is easy in case of malfunction or

blocked pump.

Digits in the following sections refer to the pictures in the appendix “Trou-

bleshooting”.

Before carrying out any service work, remove the fuse, pull out

the plug, or switch o󰀨 the power supply. Make sure that the pow-

er supply cannot be accidentally switched on.All rotating parts

must have stopped moving.The product must only be serviced by

trained service personnel.

Impeller stuck

1. Disconnect the power supply

2. Remove the motor cover cap.

3. Insert a screwdriver (min. 110 mm) through the plug hole and into the

slot of the shaft end.Turn the shaft right and left to free the impeller from

dirt.

Certiﬁcate number: WM-022990

Technical speciﬁcation: WMTS-106

ENGLISH

AUS

Operation by means of a power drill

1. Disconnect the power supply

2. If the product cannot be operated by electrical power, the toilet and sys-

tem can be emptied by means of a power drill.

Pressure switch pipe clogged

1. Disconnect the power supply

2. Unscrew the screw of the motor cover and remove the cover

3. If the water level is above the motor ange, empty the tank by means of

the appropriate tap and the hose (supplied).

4. Unscrew the screws of the board holder.

5. Remove the pressure switch pipe.

6. Clean the rubber hose and check the opening on the tank.

Foreign body in tank

1. Disconnect the power supply

2. Unscrew the screw of the motor cover and remove the cover

3. If the water level is above the motor ange, empty the tank by means of

the appropriate tap and the hose (supplied).

4. Unscrew the side screw of the motor ring

5. Lift the motor ange to reduce the compression of the O-ring. Insert a

screwdriver into the notch underneath the supply cable and press it down.

6. Extract the complete motor unit by means of the handles (lift the unit

vertically before tilting it).

7. Check and clean the tank and impeller/grinder.

Carbon lter

1. Remove the lter cover

2. Replace the lter

The carbon lter should be replaced once a year to ensure su󰀩cient

lter function.

Instead of using the activated carbon lter, the system can also vent

through a vent pipe with diameter 20.

7. TECHNICAL DATA

Model Hz

Volt

(V) P1 (W)

Amp

(A) Cos ᵠ

Hmax

pump

(m)

Flow

max

(m3/h)

Genix VT 50 220-240 530 2.5 0.95

0.91 8.0 7.8

• Supply voltage: see electrical data plate

• Maximum operating pressure: 90 kPa / 0.9 bar / 13 psi

• Grade of motor protection: IP44

• Protection rating: F

• Noise level: <70dB(A) to EN 12050-3

• Delayed line fuses (version 220-240v): indicative values (Ampere)

• Duty: S3 -50% 1min. (30 sec on; 30 sec o󰀨).

• Ambient temperature: da +5°C a +35°C

• Start and stop levels:

Start: 72 mm above bottom

Stop: 52 mm above bottom

The system pressure should not exceed 6 m head to guarantee a

su󰀩cient drain of the connected sanitary appliances (see rapid

guide).

• Storage temperature: -10°C +40°C

• Marking:

8. MANAGEMENT

8.1 Storage

All the pumps must be stored in a dry covered place, with possible con-

stant air humidity, free from vibrations and dust.

They are supplied in their original pack in which they must remain until the

time of installation.

ENGLISH AUS

8.2 Transport

Avoid subjecting the products to needless impacts and collisions.

8.3 Weight

The adhesive plate on the packaging indicates the total weight of the pump

9. MODIFICATIONS AND SPARE PARTS

Any modication made without prior authorisation relieves the

manufacturer of all responsibility. All the spare parts used in re-

pairs must be authentic and all accessories must be authorised

by the manufacturer, in order to ensure maximum safety of the

machines and of the systems in which they may be installed.

If the power supply cable of this appliance is damaged, the repair

must be carried out by specialised personnel to prevent all risks.

10. DISPOSAL

This product or its parts must be disposed of in an environment-friendly

manner and in compliance with the local regulations concerning the envi-

ronment; use public or private local waste collection systems.

ENGLISH

AUS

11. TROUBLESHOOTING

FAULTS CHECKS

(possible causes) REMEDIES

The motor does not start

and does not produce noise

when the starting level is

reached in the tank.

A. Supply failure.

B. Check the protection fuses. (if also the new fuse burns

out, either the cable or the motor is faulty).

C. Blocked impeller. (the thermal switch is o󰀨).

D. Pressure switch pipe blocked.

A. Reestablish the power supply.

B. Replace the fuse.Measure cable and motor. If cable or

motor is defective, replace the defective parts.

C. Free the impeller, and wait until the motor is cooled down

and the thermal switch has reset.

D. Remove the pressure switch pipe and clean the pipe.

2Motor hums but does not

operate.

A. Impeller stuck.

B. Motor or capacitor defective.

C. Control board defective.

A. Free the impeller and check that it can rotate freely.

B. Replace the motor or capacitor.

C. Replace the control board.

The motor works continu-

ously or starts at regular

intervals.

A. Water leaking from inlet into tank.

B. Water leaking back into tank from discharge pipe.

C. Pressure switch defective.

D. Excess foam.

A. Check for leaking appliances.

B. Check the non-return ap.

C. Replace the pressure switch unit.

D. Check the air vent/ Check that the basin is connected

to the top connection / Provide an air vent (See Quick

Guide).

4Motor runs but does not

evacuate water.

A. Pump or tank blocked.

B. Air lock in pump or vent hole in pump housing blocked.

A. Remove blockage.

B. Check operation of vent valve in the tank.Check that

the carbon lter is not wet.

C. Check that the vent hole in the pump housing is not

blocked.

5The service station drains

slowly.

A. Discharge pipe is too long or has an excessive num-

ber of bends.

B. The pump housing is leaky.

C. Hydraulics or grinder blocked.

A. Increase discharge pipe size.Change pipework to re-

duce number of bends.Change bends to soft bends.

B. Replace the pump housing (servicepart).

C. Check and clean the hydraulics and grinder.

Rattling noise from the lifting

station, but water is evacu-

ated.

A. Foreign body hitting the impeller/grinder. A. Remove the foreign body.

7 Odour from the tank. A. Carbon lter contaminated. A. Replace the carbon lter.

ENGLISH AUS

1.1

1.2 1.3

ENGLISH

AUS

1°

>2500 rpm

2.1 3.1 3.2

3.3 3.4

ENGLISH AUS

4.2 4.3 4.4

3.5 3.6 4.1

Otros manuales para GENIX VT

Tabla de contenidos

Otros manuales de Bomba de agua de DAB

DAB

DAB NOVA UP 180MA Manual de operación y mantenimiento

DAB

DAB MCE-150/C Manual de operación y mantenimiento

DAB

DAB VERTY NOVA 200 Manual de operación y mantenimiento

DAB

DAB GRINDER Series Manual de operación y mantenimiento

DAB

DAB FK Series Manual de operación y mantenimiento

DAB

DAB GENIX VT Series Manual de operación y mantenimiento

DAB

DAB E.sybox 30 Manual de operación y mantenimiento

DAB

DAB EVOPLUS B 120/220.32 M Manual de operación y mantenimiento

DAB

DAB KDN Series Manual de operación y mantenimiento

DAB

DAB DAB E.SYBOX Manual de operación y mantenimiento

DAB

DAB EVOSTA 2 Manual de operación y mantenimiento

DAB

DAB NOVA UP 180MA-MNA Manual de operación y mantenimiento

DAB

DAB NOVA UP MAE Series Manual de operación y mantenimiento

DAB

DAB KVC Manual de operación y mantenimiento

DAB

DAB SS6 Manual de operación y mantenimiento

DAB

DAB ALM 200 Manual de operación y mantenimiento

DAB

DAB EVOTRON Manual de usuario

DAB

DAB GENIX VT Manual de usuario

DAB

DAB PULSAR CB Manual de operación y mantenimiento

DAB

DAB EVOTRON Manual de usuario

DAB

DAB EVOPLUS SMALL 60/180 M Manual de operación y mantenimiento

DAB

DAB KVC 3/3 Manual de operación y mantenimiento

DAB

DAB CP2-G CM2-G Manual de operación y mantenimiento

DAB

DAB DAB E.SYBOX Manual de operación y mantenimiento

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario