D-Link DWL-8620AP Manual de usuario

Documentation is also available

on the D-Link website

This document will guide you through the

basic installation process for your new D-Link

Unied Wireless Access Point.

DWL-8620AP

Quick Installation Guide

Unied AC Concurrent Dual-Band PoE Access Point

LAN2

LAN1

Quick Installation Guide

2  D-Link DWL-8620AP Quick Install Guide

ENGLISH

About This Guide

This installation guide provides basic

instructions for installing the DWL-8620AP

on your network. For additional information

about how to use the access point, please

see the User Manual, which is available on

the CD included in this package or from the

D-Link support website.

Package Contents

System Requirements

This DWL-8620AP should include the

following items:

- DWL-8620AP

- Power adapter (optional)*

- Mounting ring

- Console cable (optional)**

- CD-ROM

- Ceiling bracket (3 sets: 9/16", 14/16", and

1 1/2")

If any item is missing or damaged, please

contact your local D-Link reseller.

*The power adapter is optional and is not

included for some regions. To power the

unit, use a D-Link PoE switch or the D-Link

DPE-301GE PoE Injector.

**If this item is not included, it can be

purchased separately. Please contact your

local D-Link reseller.

- CD-ROM drive

- Windows®, Macintosh®, or Linux-based

operating system

- An available Ethernet port

- Internet Explorer 11, Safari 7, Firefox 28,

Google Chrome 33 or higher

Hardware Overview

LED Indicators

Figure 1. DWL-8620AP LEDs

POWER When this LED is red,

the access point is

booting up. When it is

green, it is ready for

use.

LAN1/LAN2 When this LED is lit,

the device’s Ethernet

port is connected to an

active router or switch.

The light will ash

when data is being

transmitted through the

port.

2.4GHz/5GHz When this LED is lit,

the access point’s

wireless radio is

enabled. It will ash

when data is being

transmitted via

wireless.

Optional Accessories

- PoE Injector (Model: DPE-301GI)

Note: These accessories are not included

and can be purchased separately. Please

contact your local D-Link reseller.

D-Link DWL-8620AP Quick Install Guide  3

ENGLISH

Figure 2. DWL-8620AP Rear Panel

Interface Connectors

Powering the Access Point

The DWL-8620AP can be powered using

one of the following methods:

• (Optional) Connect the supplied power

adapter.

• Use a standard Ethernet cable to

connect LAN port 1 on the DWL-8620AP

to a PoE power source device such as a

PoE switch or PoE injector.

Hardware Installation Connecting through a switch or router:

Connect the access point and the computer

to the same switch or router. If the access

point did not acquire an IP address from

a DHCP server on the network, enter the

default IP address of the access point

10.90.90.91 in the address eld of your

browser. If the access is automatically

assigned an IP address by a DHCP server

on your network, enter the IP address

assigned to the access point into the web

browser. To log in, use the default login

information:

Username: admin

Password: admin

Switch or

Router ComputerDWL-8620AP

ComputerDWL-8620AP

Conguring the Access Point

To set up and manage the DWL-8620AP,

use one of the following methods:

Direct connection to a PC:

Connect the access point and the computer

directly via a straight-through Ethernet

cable. Ensure the computer is congured

with a static IP address in the 10.90.90.0/24

subnet. Launch a web browser, type the

default IP address of the access point

(http://10.90.90.91), then press Enter.

To log in, use the default login information:

Username: admin

Password: admin

Power Button

Power Receptor

LAN 1 Port (PoE)

LAN 2 Port

Console Port

Reset Button

Figure 3. DWL-8620AP Front Panel

Kensington Lock

LAN2

LAN1

4  D-Link DWL-8620AP Quick Install Guide

ENGLISH

4. Plug the CAT 5 cable into the LAN port on

the access point.

Mounting Using Anchor

Screws

1. Use the plastic wall mounting ring to

mark the points where you will insert the

screws on a wall or ceiling.

2. Drill holes in the marked points and

Installation

Mounting Options

You can mount the DWL-8620AP access

point on any of the following types of

surfaces:

• Solid surface wall or ceiling

• Tabletop

Cable Requirement

Use a CAT 5 cable with an even sheath.

The Ethernet ports on the DWL-8620AP

access point cannot accept a CAT 5 cable

that has an uneven sheath; the RJ-45

connector on the cable will not fit properly into

the receptacle on the access point.

Wall Installation Recommendations

If you plan to install the DWL-8620AP on a

wall or other vertical surfaces, orient the top

of the access point (the side with the LEDs)

toward the intended coverage area. The

radio antennas transmit through the top of

the access point but not through the bottom

(where the bracket is).

insert the plastic wall anchors.

3. Use the supplied screws to attach the

mounting ring to the wall.

Warning: The DWL-8620AP is designed

to receive PoE power only from an 802.3at-

compliant source or from a D-Link-approved

power adapter. Connecting an access point

to a Power over Ethernet (PoE) device that

is not approved by D-Link can damage the

equipment.

Warning: This product is to be connected

only to indoor PoE networks with no outdoor

cable routing.

• Connecting through a Unied

Wireless Switch or Wireless

Controller: Connect the access point

to a Unied Wireless Switch or Wireless

Controller. Connect your computer to

the same network as that of the Unied

Wireless Switch or Wireless Controller.

Wireless Controller's web administration

page. For the default login information

please refer to the Unied Wireless

Switch or Wireless Controller user

manual.

Unied Wireless

Switch

Wireless Controller

Computer

DWL-8620AP

D-Link DWL-8620AP Quick Install Guide  5

ENGLISH

Mounting Using Ceiling

Brackets

3. Plug the CAT 5 cable into the LAN port on

the access point.

5. Locate the right side of the access point

that has a small lock symbol on it, and

make sure to line up this side with the

side of the mounting ring that has Open -

Lock written on it.

1. Clip two ceiling brackets on the ceiling

panels. Make sure both bracket are

parallel.

4. Place the DWL-8620AP onto the

mounting ring and rotate the device

clockwise to lock it in position.

LAN2

LAN1

Installation

POWER

LAN1

LAN2

2.4GHz

5GHz

POWER

LAN

2.4GHz

POWER

LAN

2.4GHz

5GHz

Ceiling bracket

Ceiling crossbar

6. Twist clockwise to lock the access point

onto the ring. The lock symbol on the

access point must point directly to the

Close text on the mounting ring.

2. Use the provided screws to attach the

mounting ring to the ceiling bracket.

POWER

LAN1

LAN2

2.4GHz

5GHz

6  D-Link DWL-8620AP Quick Install Guide

Regulatory Statements

ErP Power Usage

This device is an Energy Related Product (ErP) with High Network Availability (HiNA), and

automatically switches to a power-saving Network Standby mode within 1 minute of no packets

being transmitted. It can also be turned o through a power switch to save energy when it is not

needed.

Network Standby: 7.2692 watts

Switched O: 0.0619 watts

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Non-modications Statement:

Any changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

Caution:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

D-Link DDWL-8620AP Quick Install Guide  7

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For

product available in the USA/Canada market, only channel 1~11 can be operated. Selection of

other channels is not possible.

Note:

The country code selection is for non-USA models only and is not available to all USA models. Per

FCC regulations, all WiFi product marketed in the USA must be xed to USA operational channels

only.

RF Frequency Requirements

This device is for indoor use only when using all channels in the

5.150 GHz - 5.250 GHz, 5.250 GHz - 5.350 GHz, 5.470 GHz - 5.725 GHz, 5.725 GHz - 5.850 GHz

frequency range. High power radars are allocated as primary users of the

5.150 GHz - 5.250 GHz, 5.250 GHz - 5.350 GHz, 5.470 GHz - 5.725 GHz, 5.725 GHz - 5.850 GHz

bands. These radar stations can cause interference with and/or damage this device. This device

will not operate on channels which overlap the 5600-5650 MHz band.

It is restricted to indoor environments only.

IMPORTANT NOTICE:

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 37 cm

between the radiator and your body.

Industry Canada statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject

to the following two conditions:

1) this device may not cause interference, and

2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

1) l'appareil ne doit pas produire de brouillage, et

2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

8  D-Link DWL-8620AP Quick Install Guide

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that

this device does not cause harmful interference.

Cet appareil est conforme à la norme RSS-310 d'Industrie Canada. L'opération est soumise à la

condition que cet appareil ne provoque aucune interférence nuisible.

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter, except tested built-in radios.

Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une

autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

The County Code Selection feature is disabled for products marketed in the US/ Canada.

La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux

États-Unis et au Canada.

Caution :

i. the device for operation in the band 5150–5250 MHz is only for indoor use to reduce

the potential for harmful interference to co-channel mobile satellite systems;

ii. for devices with detachable antenna(s), the maximum antenna gain permitted for

devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still

complies with the e.i.r.p. limit

iii. for devices with detachable antenna(s), the maximum antenna gain permitted for

devices in the band 5725-5850 MHz shall be such that the equipment still complies with the

e.i.r.p. limits as appropriate;

iv. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s)

necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section

6.2.2.3 shall be clearly indicated.

v. users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could

cause interference and/or damage to LE-LAN devices.

Avertissement:

i. les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés

uniquement pour une utilisatin à l’intérieur an de réduire les risques de brouillage préjudiciable

aux systèmes de satellites mobiles utilisant les mêmes canaux

ii. pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis

D-Link DDWL-8620AP Quick Install Guide  9

以下警語適用台灣地區

依據低功率電波輻射性電機管理辦法

第十二條: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自

變更頻率、加大功率或變更原設計之特性及功能。

第十四條: 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象

時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之

無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之

干擾。

應避免影響附近雷達系統之操作。

無線傳輸設備 (UNII)

無線資訊傳輸設備忍受合法通信之干擾且不得干擾合法通信；如造成干擾，應立即停用，俟

無干擾之虞，始得繼續使用。無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商

使用手冊上所述正常操作，發射的信號應維持於操作頻帶中。

NCC 警語：

電磁波曝露量MPE標準值(MPE) 1 mW/cm2，送測產品實值為 1 mW/cm2

Radiation Exposure Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 37 cm

between the radiator and your body.

Déclaration d'exposition aux radiations

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 37

cm de distance entre la source de rayonnement et votre corps.

pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit être

conforme à la limite de la p.i.r.e;

iii. pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis

(pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la

p.i.r.e. spéciée, selon le cas;

iv. lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de modèle

de l’antenne et les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de

la p.i.r.e. applicable au masque d’élévation, énoncée à la section 6.2.2.3, doivent être clairement

indiqués.

v. users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could

cause interference and/or damage to LE-LAN devices.

10  D-Link DWL-8620AP Quick Install Guide

Frequency Band(s)

Frequenzband

Fréquence bande(s)

Bandas de Frecuencia

Frequenza/e

Frequentie(s)

Max. Output Power (EIRP)

Max. Output Power

Consommation d’énergie max.

Potencia máxima de Salida

Potenza max. Output

Max. Output Power

5 G

5.15 – 5.25 GHz 200 mW

5.25 – 5.35 GHz 200 mW

5.47 – 5.725 GHz 1 W

2.4 G 2.4 – 2.4835 GHz 100 mW

Otros manuales para DWL-8620AP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de D-Link

D-Link

D-Link DAP-1665 Manual de usuario

D-Link

D-Link DAP-3860 Manual de usuario

D-Link

D-Link DWL-AG700AP - AirPlus AG - Wireless Access... Manual de usuario

D-Link

D-Link DVA-G3670B Manual de usuario

D-Link

D-Link DAP-1365 Manual

D-Link

D-Link DWR-730 Manual de usuario

D-Link

D-Link AirPremier DWL-1700AP Manual de usuario

D-Link

D-Link WL-7620AP Manual de usuario

D-Link

D-Link DAP-1665 Manual de usuario

D-Link

D-Link DAP-2553 - Wireless N Dual Band Gigabit Access... Manual de usuario

D-Link

D-Link DAP-2230 Manual de usuario

D-Link

D-Link AirXpert DWL-7000AP Manual de usuario

D-Link

D-Link DWL-2600AP Manual de servicio

D-Link

D-Link DWL-3260AP - AirPremier - Wireless Access... Manual de usuario

D-Link

D-Link D DWL-8200AP DWL-8200AP Manual de usuario

D-Link

D-Link DWL-8620APE Manual de usuario

D-Link

D-Link Nuclias Connect DAP-2622 Manual de usuario

D-Link

D-Link DAP-3310 Manual de usuario

D-Link

D-Link DWL-3200AP - AirPremier - Wireless Access... Manual de usuario

D-Link

D-Link DWL-6610APE Manual de usuario

D-Link

D-Link Rangebooster N 650 Access Point DAP-1353 Manual de usuario

D-Link

D-Link DWL-700AP - Air - Wireless Bridge Manual de usuario

D-Link

D-Link DWL-8600AP Manual de usuario

D-Link

D-Link DAP-3666 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

EnGenius

EnGenius EAP350 Manual de usuario