D-Link AirPremier DWL-7700AP Manual de usuario

DWL-7700AP

802.11a/b/g Access Point

Command Line Interface Reference Manual

Ver. 3.2 (February 2009)

RECYCLABLE

Table of Contents

Using the CLI ......................................................................................................................................................................................................................1

Command Syntax................................................................................................................................................................................................................5

Utility Commands ...............................................................................................................................................................................................................7

Ethernet Commands ...........................................................................................................................................................................................................8

Wireless Commands............................................................................................................................................................................................................9

Multi-SSID and VLAN Commands .....................................................................................................................................................................................14

Access Control List Commands .........................................................................................................................................................................................16

Radius Server Commands .................................................................................................................................................................................................18

DHCP Server Commands...................................................................................................................................................................................................19

Snmp Commands..............................................................................................................................................................................................................20

Time Display & SNTP Commands ......................................................................................................................................................................................22

Telnet & SSH Commands ..................................................................................................................................................................................................23

System Log & SMTP Command .........................................................................................................................................................................................25

First-Time Configuration Examples ...................................................................................................................................................................................26

802.11 a/b/g Access Point Command Line Interface Manual

USING THE CLI

The DWL-7700AP can be accessed by Telnet. Using Microsoft Windows Operation system as example, open the Command Prompt on the computer that will be used for configuring and

managing the AP and enter telnet and IP address of DWL-7700AP in the first line. Using the default IP address as example, enter telnet 192.168.0.50 to cause the following screen to open:

Press Enter in the screen above. The following screen opens:

Type “admin” for the D-Link Access Point login username in the screen above and press Enter. The following screen opens:

802.11 a/b/g Access Point Command Line Interface Manual

Press Enter as there is no initial password.

The following screen opens to indicates you have successfully logged into the DWL-7700AP.

Commands are entered at the command prompt, D-Link Access Point wlan1 – >

802.11 a/b/g Access Point Command Line Interface Manual

There are a number of helpful features included in the CLI. Entering the “?” command and then pressing Enter will display a list of all of the top-level commands. The same information

can also be displayed by entering “help”.

Press Enter to see a list of all the available commands. Alternatively, you may enter “help” and the press Enter.

When you enter a command without all of its required parameters, the CLI will prompt you with a list of possible completions. For example, if “tftp” was entered, the following screen

opens:

802.11 a/b/g Access Point Command Line Interface Manual

This screen displays all the possible command completions for “tftp”

When you enter a command without a variable or value that needs to be specified, the CLI will prompt you with further information about what is needed to complete the command. For

example, if “snmp authtrap” was entered, the following screen opens:

The missing value for the “snmp authtrap”command, “enable/disable,” is displayed in the screen above.

802.11 a/b/g Access Point Command Line Interface Manual

COMMAND SYNTAX

The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the CLI and available

through the console interface uses the same syntax.

Note: All commands are case-insensitive.

Purpose Encloses a variable or value that must be specified.

Syntax set login <username>

Description In the above syntax example, you must specify the username.

Do not type the angle brackets.

Example Command set login accounting

[square brackets]

Purpose Encloses a required value or set of required arguments. One

value or argument can be specified.

Syntax get multi-authentication [index]

Description In the above syntax example, you must specify an index to be

created. Do not type the square brackets.

Example Command get multi-authentication 2

802.11 a/b/g Access Point Command Line Interface Manual

: colon

Purpose Separates two or more mutually exclusive items in a list, one of

which must be entered.

Syntax set antenna [1:2:best]

Description In the above syntax example, you must specify either 1,2 or

best. Do not type the colon.

Example Command set antenna best

802.11 a/b/g Access Point Command Line Interface Manual

UTILITY COMMANDS

Help Command: Function Syntax

help Display CLI Command List help or ?

Ping Command: Function Syntax

ping Ping ping <xxx.xxx.xxx.xxx>

Restart and Exit Commands: Function Syntax

set factorydefault Restore to Default Factory Settings set factorydefault

reboot Reboot Access Point. It is necessary to reboot the AP after making

configuration changes for those changes to take effect. reboot

quit Logoff quit

Version Display Command: Function Syntax

version Displays the currently loaded firmware version version

System Status Command: Function Syntax

get bdtempmode Display Monitor Board Temperature Mode get bdtempmode

set bdtempmode Set Monitor Board Temperature Mode (In Centigrade) set bdtempmode [enable:disable]

get bdalarmtemp Display Monitor Board Temperature Alarm Limitation (In Centigrade) get bdalarmtemp

set bdalarmtemp Set Monitor Board Temperature Alarm Limitation (In Centigrade) set bdalarmtemp <temperature>

get bdcurrenttemp Display Current Board Temperature (In Centigrade) get bdcurrenttemp

set detectlightmode Set HW Detect Light Mode set detectlightmode [enable:disable]

Addminstration Command: Function Syntax

get login Display Login User Name get login

get uptime Display UpTime get uptime

set login Modify Login User Name set login <username>

set password Modify Password set password

get wlanManage Display manage AP with WLAN Mode get wlanManage

set wlanmanage Set manage AP with WLAN Mode set wlanmanage [enable:disable]

get systemname Display Access Point System Name get systemname

set systemname Specify Access Point System Name set systemname <name>

Other Command: Function Syntax

radar! Simulate radar detection on current channel radar!

802.11 a/b/g Access Point Command Line Interface Manual

ETHERNET COMMANDS

Get Command: Function Syntax

get ipaddr Display IP Address get ipaddr

get ipmask Display IP Network/Subnet Mask get ipmask

get gateway Display Gateway IP Address get gateway

get lcp Display Link Integrate state get lcp

get lcplink Display Ethernet Link State get lcplink

get dhcpc Display DHCP Client State of enabled or disabled get dhcpc

get domainsuffix Display Domain Name Server Suffix get domainsuffix

get nameaddr Display IP Address Of Name Server get nameaddr

Set Command: Function Syntax

set hostipaddr Set Boot Host IP Address set hostipaddr <xxx.xxx.xxx.xxx>

Explanation:<xxx.xxx.xxx.xxx>is IP address

set ipaddr Set IP Address set ipaddr <xxx.xxx.xxx.xxx>

Explanation: <xxx.xxx.xxx.xxx> is IP address

set ipmask Set IP Network/Subnet Mask set ipmask < xxx.xxx.xxx.xxx>

Explanation: <xxx.xxx.xxx.xxx> is Network mask

set lcp Set Lcp State set lcp [0:1]

Explanation:0=disable 1=enable

set gateway Set Gateway IP Address set gateway <xxx.xxx.xxx.xxx>

Explanation: <xxx.xxx.xxx.xxx> is Gateway IP address

set dhcpc Set DHCP Clinet State of enable or disabled set dhcp[disable:enable]

set domainsuffix Set Domain Name Server Suffix set domainsuffix <suffix>

set nameaddr Set Name Server IP Address set nameaddr [1:2] <xxx.xxx.xxx.xxx>

set ethctrl ethernet control Speed and FullDuplex

set ethctrl[0:1:2:3:4]

Explanation:

0: Auto

1: 100M FullDuplex

2: 100M HalfDuplex

3: 10M FullDuplex

4: 10M HalfDuplex

Otros manuales para AirPremier DWL-7700AP

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de D-Link

D-Link

D-Link DWL-6600AP Manual de usuario

D-Link

D-Link DWS-3024L Manual de usuario

D-Link

D-Link DWL-8600AP Manual de servicio

D-Link

D-Link DAP-2660 Manual de usuario

D-Link

D-Link DAP-2553 - Wireless N Dual Band Gigabit Access... Manual de usuario

D-Link

D-Link Rangebooster N 650 Access Point DAP-1353 Manual de usuario

D-Link

D-Link DAP-1620 Manual

D-Link

D-Link DWL-3600AP Manual de usuario

D-Link

D-Link DAP-1513 Manual de usuario

D-Link

D-Link DAP-3220 Manual de usuario

D-Link

D-Link DWL-6610AP Manual de usuario

D-Link

D-Link AirPro DWL-6000AP Manual de usuario

D-Link

D-Link DAP-2020 Manual de usuario

D-Link

D-Link AirPremier N DAP-2310 Manual de usuario

D-Link

D-Link AirPremier N DAP-2690 Manual de usuario

D-Link

D-Link DAP-1160 Manual de usuario

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

D-Link

D-Link DAP-1665 Manual de usuario

D-Link

D-Link DAP-1160 Manual de usuario

D-Link

D-Link DAP-600P Manual de usuario

D-Link

D-Link nuclias connect DAP-2662 Manual de usuario

D-Link

D-Link AirPremier N DAP-2310 Manual de usuario

D-Link

D-Link AirPlus DWL-900AP+ Manual de usuario

D-Link

D-Link DWL-3260AP - AirPremier - Wireless Access... Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

EnGenius

EnGenius EAP350 Manual de usuario