D-Link Nuclias DNH-100 Manual de usuario

www.dlink.com

Manual how to bind the

Switches into the Nuclias Connect

For Nuclias Connect Hardware DNH-100 Rev.A and Nuclias Connect Software DNC-100

For SWITCH Rev.F and Rev.G

To bind the switch into the Nuclias Connect please follow these steps.

1. Requirements

- DGS-1210 in Rev.F with firmware version 6.30.xx or higher

- DGS-1210 in Rev.G with firmware version 7.30.xx or higher

- DGS-1100V2 in Rev.A with 10 Ports and more with the

Firmware version 4.00b019 or higher

- DXS-1210 in Rev.B with Firmware version 2.01b10 or higher

- DNH-100 Nuclias Conenct Hub with the actual Firmware 1.2.1.7 or higher.

Or DNC-100 Nuclias Connect Software in the actual Version 1.2.1.3 or higher.

The firmware files and software you can download from our D-A-CH-BE-NE-LUX

web sites https://www.dlink.com or https://ftp.dlink.de

2. Preparations

Different to the DAP Access Points the switch must be pre-configured so far

that it got an IP-address from the DHCP-Server in the network or has a static

IP-address compatible to the network.

By default the switch has the static IP-address 10.90.90.90

with subnet mask 255.0.0.0

Change the TCP/IP of the network connection temporarily to configure the

switch.

Alternative or if you don’t know the IP-address of your switch you can use our

Software D-Link Network Assistant (DNA) to find it out or to change it.

See following screenshot.

www.dlink.com

You can download the DNA from

https://ftp.dlink.de/software/DNA/D-Link_Network_Assistant_DNA_40021_all_en.zip

With the PC mouse go over the switch entry and then click on IP on the right side.

Then you can change the IP-address of the switch.

Note:

In the following steps granting that you already made a setup in

your DNH-100 / DNC-100 (following named as NC) and have it in use

with DAP-models, so the NC has a basic setup already.

3. Call the setup of your NC and log-in.

We recommend to use the English setup because the translation in other

languages isn’t fine sometimes.

- Chose English.

- Enter the username admin and your configured Admin-password.

- If necessary enter the displayed CAPTCHA.

- Click onto Login.

www.dlink.com

4. On the left go to the menu Configuration and then Create Profile.

Upper-right click onto Add Network to create a new Switch-Profile.

Note:

Switches can’t be bound into AP-Profiles, also AP not into Switch-Profiles.

5. Create a newSite or chose an already existing Site, in this you added an Access

point profile and then add a new Network.

For this give (the site and) the Network a name and then click on Next.

www.dlink.com

6. - Chose the Country where the switch has to work.

- If necessary modify the Time Zone.

- Set a hook at Switch.

- At Series Supported you must mark the Switch-Type this you want to add.

- At Password you must enter the Admin-password this the switch has to get

from the NC-Profile as soon as it will be bound-in.

Click on Next.

7. Normally it is fine to use Layer 2.

Click on Next.

www.dlink.com

8. Upper-left click onto Discovery to let search for switches.

9. The available and compatible switches in the network will be found.

Mark the switch this you want to bind into the NC-Profile.

Enter the Admin-password this the switch actually has.

- The default Admin-password is admin.

- If you already have changed the Admin-password then enter this.

Click on Import to take over the marked swich into the NC-Profile.

www.dlink.com

Recommendation!!

For each switch create an own NC-Profile: An own Site or an already exiting site with an

own Network each.

Else it can become difficult because the NC displays all LAN ports of all switches in the

NC-profile like they are one switch.

Example: The LAN ports of three DGS-1210-10P will be listed as 30 ports –a

differentiation which port if from which switch won’t be so easy.

10. Click on Yes.

11. The displayed NC flickers a few times now.

Please what until this ends.

Click on Apply & Exit.

www.dlink.com

12. After 3-5 minutes the switch will be displayed in the Dashboard.

Click onto this…

… then the Status of the switch will be displayed.

Normally at this moment it is boarding.

Status is orange = Boarding

After additionally 3-5 minutes the Status is green = Connected

The switch can be managed and configured via the NC now.

www.dlink.com

13. To access the possible settings of the switch in the NC, on the left go to the

menu Configuration and then Profile Settings.

There inside the created profile of the switch you can make several settings.

With it the binding of the switch into the Nuclias Connect is finished.

Example:

Each a DGS-1210 Rev.F and G is bound into the Nuclias Connect:

www.dlink.com

Please see also the following manuals

Basic Setup of the DNH:

https://ftp.dlink.de/dnh/dnh-100/documentation/DNH-

100_howto_reva_Grundrichtung_de.pdf

The Nuclias Connect app:

https://ftp.dlink.de/dnh/dnh-100/documentation/DNH-

100_howto_reva_NucliasConnectApp_de.pdf

Tips:

https://ftp.dlink.de/dnh/dnh-100/documentation/DNH-100_howto_reva_Tipps_de.pdf

For further manuals please visit our FTP server

https://ftp.dlink.de/dnh/dnh-100/documentation/

and our websites

https://www.dlink.com/de/de

https://www.dlink.com/be/fr

https://www.dlink.com/be/nl

https://www.dlink.com/nl/nl

Otros manuales para Nuclias DNH-100

Otros manuales de Cambiar de D-Link

D-Link

D-Link DGS-1024T - Switch Manual de usuario

D-Link

D-Link DES-1016D - Switch Manual de usuario

D-Link

D-Link DGS-1008MP Manual de usuario

D-Link

D-Link DES-3028 Manual de usuario

D-Link

D-Link DGS-3000-28SC/A1A Manual

D-Link

D-Link DIS-100G-8W Manual de usuario

D-Link

D-Link DES-3528 - xStack Switch - Stackable Manual de instrucciones

D-Link

D-Link DGS-3130-54TS Manual de usuario

D-Link

D-Link DGS-1216T - Switch Manual de usuario

D-Link

D-Link DGS-105 - Switch Manual de usuario

D-Link

D-Link DGS-510 Manual de usuario

D-Link

D-Link DGS-1008P Manual de usuario

D-Link

D-Link DGS-3324SR Manual de usuario

D-Link

D-Link xStack Manual

D-Link

D-Link DES-F1010P-E Manual de usuario

D-Link

D-Link DES-3326 Manual de usuario

D-Link

D-Link DGS-1100-08V2 Manual de usuario

D-Link

D-Link DES-1228 - Web Smart Switch Manual de usuario

D-Link

D-Link DES-1252 - Web Smart Switch Manual de usuario

D-Link

D-Link xStack DGS-3120 Series Manual de usuario

D-Link

D-Link EasySmart DGS-1100-08 Manual de usuario

D-Link

D-Link Nuclias DNH-100 Manual de usuario

D-Link

D-Link DKVM-8E Manual de usuario

D-Link

D-Link DES-1100-10P Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manual de usuario