D-Link GO-SW-5E Manual de usuario

GO-SW-5E

5-PORT FAST ETHERNET

EASY DESKTOP SWITCH

Manual

RECYCLABLE

V1.01

TABLE OF CONTENTS

ABOUT THIS GUIDE .......................................................................1

PURPOSE.............................................................................................1

INTRODUCTION ..............................................................................2

FAST ETHERNET TECHNOLOGY .........................................................2

D-LINK’S GREEN TECHNOLOGY........................................................2

SWITCHING TECHNOLOGY.................................................................3

FEATURES ..........................................................................................4

UNPACKING AND SETUP..............................................................6

UNPACKING........................................................................................6

SETUP.................................................................................................6

IDENTIFYING EXTERNAL COMPONENTS ..............................7

FRONT PANEL ....................................................................................7

LED INDICATORS...............................................................................7

REAR PANEL ......................................................................................8

SIDE PANEL........................................................................................8

CONNECTING THE SWITCH........................................................9

PC TO GO-SW-5E..............................................................................9

HUB TO GO-SW-5E...........................................................................9

GO-SW-5E TO OTHER DEVICES.........................................................9

PORT SPEED &DUPLEX MODE ........................................................10

TECHNICAL SPECIFICATIONS.................................................11

RJ-45 PIN SPECIFICATION .........................................................13

ABOUT THIS GUIDE

Congratulations on your purchase of the D-Link GO-SW-5E. This device

integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network

capabilities in one high-performance, easy-to-use solution.

Purpose

This manual will familiarize you with the GO-SW-5E and guide you

through the installation process.

INTRODUCTION

Fast Ethernet Technology

The growing importance of LANs and the increasing complexity of

desktop computing applications are fueling the need for high performance

networks. 100BASE-T (Fast Ethernet) provides a cost-effective and high-

performance solution for small workgroups, SMBs (Small to Medium

Businesses), and any network supporting bandwidth-intensive applications.

Fast Ethernet technology operates at 10 times the speed of traditional

Ethernet, offering maximum performance and enhanced capability for

existing Ethernet-based networks.

100Mbps Fast Ethernet is a standard specified by the IEEE 802.3 LAN

committee. It is an extension of the 10Mbps Ethernet standard with the

ability to transmit and receive data at 100Mbps, while maintaining the

CSMA/CD Ethernet protocol. Since the 100Mbps Fast Ethernet is

compatible with all other 10Mbps Ethernet environments, it provides a

straightforward upgrade and takes advantage of the existing investment in

hardware, software, and personnel training.

D-Link’s Green Technology

D-Link’s Green Technology implements special power-saving features

under speed at 100Mbps that link status and adjust power usage

accordingly. Further, D-Link Green implements the newly ratified IEEE

802.3az Energy Efficient Ethernet standard for reducing energy

consumption of network links during periods of low utilization by

transitioning interfaces into low-power state without interrupting the

network connection.

•IEEE 802.3az Energy-Efficient Ethernet (EEE):

It is the first standard in the history of Ethernet to address proactive

reduction in energy consumption for networked devices. The IEEE 802.3

EEE standard defines mechanisms and protocols intended to reduce the

energy consumption of network links during periods of low utilization, by

transitioning interfaces into a low-power state without interrupting the

network connection.

•Power Saving Technology:

Power saving by link status. If there is no link on a port, such as when

there is no computer connected to the port or the connected computer is

powered off, D-Link’s Green Technology will enter a "sleep mode",

drastically reducing power used for that port.

Switching Technology

Switching is a cost-effective way of increasing the total network capacity

available to users on a LAN. If an Ethernet network begins to display

symptoms of congestion, low throughput, slow response times, and high

rates of collision, installing a switch to a network can preserve much or all

of the existing network's cabling and workstation interface card

infrastructure, while still greatly enhancing the throughput for users. A

switch is a viable solution even if demanding applications, such as

multimedia production and video conferencing, are on the horizon. The

most promising techniques, as well as the best return on investment, could

well consist of installing the right mixture of Ethernet switches.

A switch increases capacity and decreases network loading by dividing a

local area network into different LAN segments. Dividing a LAN into

multiple segments is one of the most common ways of increasing available

bandwidth. If segmented correctly, most network traffic will remain within

a single segment, enjoying the full-line speed bandwidth of that segment.

Switches provide full-line speed and dedicated bandwidth for all

connections. This is in contrast to hubs, which use the traditional shared

networking topology, where the connected nodes contend for the same

network bandwidth. When two switching nodes are communicating, they

are connected with a dedicated channel between them, so there is no

contention for network bandwidth with other nodes. As a result, the switch

considerably reduces the likelihood of traffic congestion.

For Ethernet networks, a switch is an effective way of eliminating the

problem of chaining hubs beyond the “two-repeater limit.” A switch can

be used to split parts of the network into different collision domains,

making it possible to expand your Ethernet network beyond the 205-meter

network diameter limit for 100BASE-TX networks. Switches supporting

both 10Mbps Ethernet and 100Mbps Fast Ethernet are also ideal for

bridging between existing 10Mbps networks and newer 100Mbps

networks.

Switching LAN technology is a marked improvement over the previous

generation of network hubs and bridges, which were characterized by

higher latencies. Routers have also been used to segment local area

networks, but the cost of a router, the setup and maintenance required,

make routers relatively impractical. Today switches are an ideal solution

to most kinds of local area network congestion problems.

Features

The GO-SW-5E is a high performance switch designed specifically for

environments where traffic on the network and the number of users

increase continuously.

GO-SW-5E implements D-Link’s Green Technology special power-saving

features under speed at 100Mbps that link status and adjust power usage

accordingly. Furthermore, D-Link Green implements the newly ratified

IEEE 802.3az Energy Efficient Ethernet standard for reducing energy

consumption of network links during periods of low utilization by

transitioning interfaces into low-power state without interrupting the

network connection.

The GO-SW-5E, with its small, compact size, was specifically designed

for small to mid-sized workgroups. The GO-SW-5E can be installed where

space is limited; moreover, it provides immediate access to a rapidly

growing network through a wide range of user-reliable functions.

The GO-SW-5E is ideal for deployment with multiple high-speed servers

for 10Mbps or 100Mbps shared-bandwidth workgroups. With the highest

bandwidth at 200Mbps (100Mbps full-duplex mode), any port can provide

workstations with a congestion-free data pipe for simultaneous access to

the server.

The GO-SW-5E is scalable, allowing two or more GO-SW-5E to be

cascaded together. Since all ports support 200Mbps, any one of its five

ports may be used to cascade to an additional switch to open a Full-Duplex

Fast Ethernet pipe.

The GO-SW-5E is the perfect choice for a department or office planning

to upgrade to Fast Ethernet. The GO-SW-5E can accommodate 10Mbps

or 100Mbps devices, providing a flexible solution for existing (10Mbps)

Ethernet workgroups.

The GO-SW-5E combines dynamic memory allocation with store-and-

forward switching to ensure that the buffer is effectively allocated for each

port; and it controls the data flow between the transmit and receive nodes

to guarantee against possible packet loss.

The GO-SW-5E is an unmanaged 10/100Mbps Fast Ethernet switch that

offers solutions for the accelerating bandwidth needs of small Ethernet

workgroups.

Other key features include:

Auto-MDI/MDI-X function supports automatic MDI/MDI-X

crossover detection, giving true ‘plug and play’ capability—Crossover

or Straight-Through CAT5 cables can be plugged into any port.

Nway Auto-negotiation for any port. This allows for auto-sensing of

speed (10/100Mbps), providing an automatic and flexible solution for

the network.

Flow control for any port. This minimizes dropped packets by sending

out collision signals when the port’s receiving buffer is full.

Data filtering rate eliminates all error packets, runts, etc., per port at

wire-speed for 100Mbps operation and 10Mbps operation.

UNPACKING AND SETUP

Unpacking

Open the box and carefully unpack it. The box should contain the

following items:

One GO-SW-5E: 5-PORT FAST ETHERNET EASY DESKTOP

SWITCH

One External Power Adapter

Quick Installation Guide

If any item is missing or damaged, please contact your local reseller for a

replacement.

Setup

The setup of the GO-SW-5E can be performed using the following steps:

The power outlet should be within 1.82 meters (6 feet) of the Switch.

Visually inspect the DC power jack and make sure that it is fully

secured to the power adapter.

Do not cover the ventilation holes on the sides of the Switch, and

make sure there is adequate ventilation around it.

Do not place heavy objects on the switch.

IDENTIFYING EXTERNAL COMPONENTS

Front Panel

The figure below shows the front panel of the GO-SW-5E.

GO-SW-5E 5-PORT FAST ETHERNET EASY DESKTOP SWITCH

LED Indicators

Power Indicator:

This green indicator light is on when the Switch is receiving power;

otherwise, it is off.

Link/Act:

This LED indicator light is green when the port is connected to a

device. The green indicator blinks as data is transmitted or received.

Rear Panel

Auto MDI/MDI-X Ports:

All ports support automatic MDI/MDI-X crossover detection. The

AutoMDI/MDI-X function makes it simple to connect to the switch—just

plug either a Crossover or Straight-Through CAT5 cable into any port.

Side Panel

Power Jack:

Power is supplied through an external power adapter. Check the technical

specification section for information about the power input voltage.

Since the GO-SW-5E does not require a power button, plugging its power

adapter into a power outlet will immediately power it on.

GO-SW-5E 5-PORT FAST ETHERNET EASY DESKTOP SWITCH

Otros manuales para GO-SW-5E

Tabla de contenidos

Otros manuales de Cambiar de D-Link

D-Link

D-Link DIS-F200G Series Manual de usuario

D-Link

D-Link Nuclias DNH-100 Manual de usuario

D-Link

D-Link DES-3226S Manual de usuario

D-Link

D-Link DUB-1341 Manual de usuario

D-Link

D-Link DFE-2600 Series Manual de usuario

D-Link

D-Link DGS-3630 SERIES Manual de usuario

D-Link

D-Link DIS-RK200G Manual de usuario

D-Link

D-Link DUB-2325 Manual de usuario

D-Link

D-Link DXS-3227P - xStack Switch - Stackable Manual de usuario

D-Link

D-Link DGS-2000 Series Manual de usuario

D-Link

D-Link DUB-1370 Manual de usuario

D-Link

D-Link DGS-3312SR Manual de usuario

D-Link

D-Link DUB-H7 - Hub - USB Manual de usuario

D-Link

D-Link xStack DGS-3324SRi Manual de usuario

D-Link

D-Link DGS-1224TP - Web Smart Switch Manual de usuario

D-Link

D-Link DXS-3227P - xStack Switch - Stackable Manual de usuario

D-Link

D-Link xStack DGS-3620-52P Manual de usuario

D-Link

D-Link TM DES-6500 Manual de usuario

D-Link

D-Link DIS-F100G Series Manual de usuario

D-Link

D-Link xStack DES-3500 Series Manual de usuario

D-Link

D-Link DES-2212 Manual de usuario

D-Link

D-Link 1016T - DGS Switch Manual de usuario

D-Link

D-Link Nuclias DNH-100 Manual de usuario

D-Link

D-Link DSH-16 - Hub Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manual de usuario