D-Link Express Ethernetwork DI-704P Manual de usuario
1
This product can be set up using
any current Web browser, i.e.,
Internet Explorer or Netscape
Navigator.
DI-704P
Ethernet Broadband
Router and Print Server
5V DC Power Adapter
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
specifications subject to change without notice. DI-704P. 08122003
Before You Begin
1. If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for configuring
the DI-704P Broadband Router. The DI-704P acts as a DHCP server and will assign
all the necessary IP address information on your network. See Appendix at the
end of this Quick Installation Guide or the Manual on the CD-ROM for setting
each network adapter to automatically obtain an IP address.
Check Your Package Contents
DI-704P Ethernet Broadband Router
CD-ROM (containing Manual, Warranty and
Print Server Software for Windows)
Ethernet (Straight Through) Cable
Using a power supply
with a different voltage
rating will damage and void
the warranty of this product.
If any of the above items are missing, please contact your reseller.
2
Connecting The DI-704P Broadband
Router To Your Network
B. WAN Port This is for the
connection of an Ethernet cable
to the Cable or DSL modem
C. LAN Ports These are the
connections for Ethernet cables
to Ethernet enabled computers.
D. Printer Port You
can connect a Printer to
the Parallel Port here.
A. Receptor for
Power Adapter.
Reset Button Pressing this
button restores the Router to its
original factory default settings.
A. First, connect the power adapter to the receptor at the back panel of the
DI-704P and then plug the other end of the power adapter to a wall outlet or
power strip. The Power LED will turn ON to indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices may not have a on/off
switch and will require you to unplug the power adapter. Now, the DI-704P
should be powered on and the Cable / DSL modem should be turned off.
2. Cable / DSL modem (Power Off) – DI-704P (Power On)
Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL
modem. After the Ethernet cable is securely connected, power on the Cable /
DSL modem by turning on the unit or plugging in the power adapter.
3. Cable / DSL modem (Power On) – DI-704P (Power On)
Insert the other end of the Ethernet cable to the WAN PORT on the back panel
of the DI-704P. The WAN LED light will illuminate to indicate proper connection.
If the WAN LED is not illuminated, please go back to step B1 and repeat the
instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the DI-704P and an
available Ethernet port on the network adapter in the computer you will use to
configure the DI-704P. The LED light for LAN Port 1 will illuminate to indicate
proper connection. (Note: The LAN Ports on the DI-704P are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover-Ethernet cable to the LAN
Ports.)
D. The parallel port on the DI-704P is used to connect printers only. Connect one
end of the printer cable to your printer and the other end to the DI-704P.
3
Restart Your Computer
Connecting Additional Computers To
The DI-704P
Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-equipped
computers to the remaining Ethernet LAN ports on the back panel of the DI-704P
WAN LED – a
solid light indicates
connection on the
WAN port. This
LED blinks during
data transmission.
LOCAL NETWORK
LEDs – a solid light
on the port indicates a
connection to an
Ethernet enabled
computer on ports 1-4.
This LED blinks during
data transmission.
POWER LED – a solid
light indicates a proper
connection to the
power supply.
M1 LED – will flash
consistently to indicate
that the DI-704P is
working properly.
M2 LED – a solid light indicates
that Internet connection has
been established.
4
When you have completed the steps in this Quick Installation
Guide, your connected network should look similar to this:
Using The Setup Wizard
The logon pop-up screen will appear.
Open your Web browser and
type “http://192.168.0.1” into the
URL address box. Then press the
Enter or Return key.
Type “admin” for the username and
leave the password field blank.
Click OK
5
The Setup Wizard (continued)
Once you have logged in, the
Home screen will appear.
You will see the following screens
Set up your new password.
You have the option to
establish a password.
Click Run Wizard
Click Next
Click Next
6
The Setup Wizard (continued)
Select your Internet Connection.
You will be prompted to select the type
of Internet connection for your router.
If you are unsure of which setting to select,
please contact your Internet Service Provider.
If you selected Dynamic IP Address,
this screen will appear: (Used mainly
for Cable Internet service.)
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You can
also manually type in the MAC
address.
Click Next
This setup should be done on the computer
that is registered on the ISP’s network.
Choose your time zone from the drop
down list.
Click Next
Click Next
7
The Setup Wizard (continued)
If your ISP requires a Static IP
Address, and this option is
selected, then this screen will
appear:
If your ISP uses PPPoE (Point-to-Point
Protocol over Ethernet), and this option
is selected, then this screen will
appear: (Used mainly for DSL Internet
service.)
Enter the IP address information
originally provided to you by your
ISP. You will need to complete all
the required fields.
Please be sure to remove any
existing PPPoE client software
installed on your computers.
Enter in the username and password
provided to you by your ISP.
Click Next
Click Next
8
Your Setup is Complete!
Click Restart
Test Internet Connection.
You will be returned to the Home tab.
For additional settings or
information, refer to the
Advanced, Tools, or
Status tabs on the web-
management interface;
or to the Manual located
on the CD.
Then relaunch your Web
browser (i.e., Internet
Explorer or Netscape
Navigator), to link to your
favorite Web site to test
your Internet connection.
Click to Exit
9
APPENDIX
Insert the installation CD-ROM into the
CD-ROM drive. The following window
will be shown automatically. If it is not,
please run “autorun.exe” on the CD-
ROM.
Installing the Print Server Software
Wait until the following Welcome
dialog appears.
Select the destination folder.
Click Next
Click Install Windows
Printer Software
Click Next
Select your Windows
operating system
10
After rebooting your computer, the software installation procedure is finished.
Installing the Print Server Software (continued)
Configuring on Windows 98se/Me Platforms
After you finish the software installation procedure, your
computer will be capable of network printing provided by
the DI-704P. On a Windows 95/98 platform, open the
Printers window in the My Computer menu.
Now, you can configure the print server of the DI-704P:
Find out the corresponding icon of your printer, for
example, the HP LaserJet 6L. Right click on that icon,
and then select Properties.
The following screen appears:
When the following window is displayed.
Click Finish
Click OK
Then, the setup program will begin to
install the programs into the destination
folder.
Otros manuales para Express Ethernetwork DI-704P
8
Tabla de contenidos
Otros manuales de Enrutador de red de D-Link
D-Link
D-Link Express Ethernetwork DI-704P Manual de usuario
D-Link
D-Link DSL-522T Manual de usuario
D-Link
D-Link DWR-555 Manual de usuario
D-Link
D-Link DIR-826L Manual de usuario
D-Link
D-Link DI-808HV Manual de usuario
D-Link
D-Link DSL-2544N Manual de usuario
D-Link
D-Link DIR-827 Manual de usuario
D-Link
D-Link AirPlus DWL-810+ Manual de usuario
D-Link
D-Link DWR-922 Manual de usuario
D-Link
D-Link WR830A1 Manual de usuario
D-Link
D-Link DES-6300 Manual de usuario
D-Link
D-Link DIR-815 Manual de usuario
D-Link
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual de usuario
D-Link
D-Link Express Ethernetwork DI-704P Manual de usuario
D-Link
D-Link DSL-224 Manual de usuario
D-Link
D-Link DI-304 Manual de usuario
D-Link
D-Link DIR-600 Manual de usuario
D-Link
D-Link DSL-2890L Manual de usuario
D-Link
D-Link DSL-2640B Manual de usuario
D-Link
D-Link myPocket DIR-457 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad