D-Link DI-704 Manual de usuario
D-Link
DI-704 Quick Installation Guide
1. Hardware Installation
A. Setup LAN connection: connect an Ethernet cable (straight-through) from your
computer’s Ethernet port to one of the LAN ports of the DI-704.
B. Setup WAN connection:connect the network cable from your cable or DSL modem
to the WAN port of the DI-704. Use the cable that came with your Cable or DSL
modem. If you don’t see a link light on the WAN LED, try the other network cable.
C. Power on: connect the power cord to power inlet and turn the power switch on. The
DI-704 will automatically enter the self-test phase. When in the self-test phase, the
indicators M1 and M2 will be lit for about 5 seconds, and then M1 and M2 will flash
three times to indicate that the self-test operation has finished. Finally, the M1 will
flash continuously once per second to indicate that the DI-704 is in normal operation.
*If you are using PPPoE, begin Step 5.
If you are not using PPPoE, proceed to Step 2 below.
2. Find and Write Down Your Computer's Internet Settings
A. Open the Control Panel
B. Find and Double Click the Network Icon
-1-
C. Click the Identification Tab
D. Write down your computer name on a sheet of paper.
E. Click the Configuration Tab. It should list your network (Ethernet) adapter and the
loaded network protocols and services. Find TCP/IP for the network adapter
connected to your Cable/DSL modem.
F. Find and double click the TCP/IP setting for your Network Adapter that connects to
your cable or DSL modem.If you have not yet installed your network card, install
your network card,and then return to this step. You should see one of the following
screens:
-2-
or
G. Write down whether "Obtain An IP Address Automatically" or "Specify an IP
Address" is checked.
H. If Specify is checked, write down the IP Address ____. ____. ____. ____ and Subnet
Mask ____.____.____.____ on a sheet of paper.
I. If Specify is checked, find and write down your Gateway address
____.____.____.____ by clicking on the Gateway tab.
J. Find and write down your host name ___________________. It is listed under the
DNS Configuration Tab.
-3-
K. If Specify was checked, find and write down your DNS Server addresses
_____.____.____.____ , ____.____.____.____. There are normally two, but only one
is needed. In step 4 all of this information will be required to configure the DI-704
with your provider.
3. Reconfigure your TCP/IP settings
A. Click the IP Address tab. Select Obtain an IP address automatically.
B. Click the Gateway tab. Clear all of the gateway settings. Click on the OK button.
C. Disable DNS settings
-4-
4. Configure the DI-704 without PPPoE
A. Launch Netscape or Internet Explorer. You must use Netscape 4.0 or Internet
Explorer 4.0 or higher. If you are using proxy settings, either remove the proxy
settings or add the IP address of the DI-704 into the exceptions box. Type the DI-
704’s IP address (default is: http://192.168.0.1) in the Location (for Netscape) or
Address (for IE) field and press ENTER.
B. Key in the system password (the factory default setting is ”admin”) in the System
Password field and click on the Log inbutton.
C. Press the Setup button and the following screen will be shown.
D. Press the Change…button, select the WAN type you use, and then press the Save
button. The following screen will appear.
E. Key in the proper values for the setting items shown on the page. Use the settings
that you saved from your step 2. For the meaning of the items, please press the Help
button or refer to the User Manual –Chapter 4.4.
F. After all of the items are set, press the Save button and reboot the DI-704.
You have now configured the DI-704. Refer to the User manual to review features and
operation instructions that you may need for your use.
5. Configure the DI-704 with PPPoE
What is PPPoE?
PPPoE stand for Point-to-Point Protocol over Ethernet. It is a non-standard method
of connecting to your ISP to gain an IP address. It relies upon a software client that is
provided by the ISP. An IP address is required to gain a connection to the Internet.
How can I tell if I am using PPPoE?
PPPoE requires a client on your computer. If you have a broadband connection and
have to login to your provider in a similar fashion to how you would dial in with a
modem, you are probably using PPPoE. If you are simply connected to the Internet
when you turn on your computer, you probably are not. The safest way to check is to
call your provider, or read the documentation provided with your Internet service to
determine if you currently use PPPoE.
A. Click the IP Address tab. Select Obtain an IP address automatically.
-5-
B. Click the Gateway tab. Clear all of the gateway settings. Click on the OK button.
C. Disable DNS settings
D. Launch Netscape or Internet Explorer. You must use Netscape 4.0 or Internet
Explorer 4.0 or higher. If you are using proxy settings, either remove the proxy
settings or add the IP address of the DI-704 into the exceptions box. Type the DI-
704’s IP address (default is: http://192.168.0.1) in the Location (for Netscape) or
Address (for IE) field and press ENTER.
E. Key in the system password (the factory default setting is ”admin”) in the System
Password field and click on the Log inbutton.
F. Press the Setup button and the following screen will be shown.
G. Press the Change…button, select PPPoE over Ethernet, and then press the Save
button. The following screen will be shown.
H. Key in the proper values for the setting items shown on the page. For the meaning
of the items, please press the Help button or refer to the User Manual –Chapter
4.4. After all of the items are set, press the Save button and reboot the DI-704.
You have now configured the DI-704. Refer to the User manual to review features and
operation instructions that you may need for your use.
Otros manuales para DI-704
2
Otros manuales de Enrutador de red de D-Link
D-Link
D-Link EXO AX COVR-X1870 Manual de usuario
D-Link
D-Link DSL-500T Manual de usuario
D-Link
D-Link DSL-526B Manual de usuario
D-Link
D-Link DVG-N5402SP Manual de usuario
D-Link
D-Link DSL-604+ Manual de usuario
D-Link
D-Link DFL-300 - Security Appliance Manual de usuario
D-Link
D-Link DSL-124 Manual de usuario
D-Link
D-Link Xstack DGS-3300 Series Manual de usuario
D-Link
D-Link DWR-920 Manual de usuario
D-Link
D-Link DWR-921E Manual de usuario
D-Link
D-Link DWR-933 Manual de usuario
D-Link
D-Link DSL-2750U Hoja de información del producto
D-Link
D-Link DWR Series Manual de usuario
D-Link
D-Link DIR-802 Manual de usuario
D-Link
D-Link DIR-615 - Wireless N Router Guía de instalación
D-Link
D-Link XTREME N DIR-655 Manual de usuario
D-Link
D-Link DSL-1500G Manual de usuario
D-Link
D-Link DIR-879 Manual de usuario
D-Link
D-Link DES-1228/ME Manual de usuario
D-Link
D-Link DSL-2544N Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad