CYP CH-507TXBD: CH-507RXBD Manual de usuario
DRAFT
CH-507TXBD & RXBD
HDMI to CAT5e/6 with LAN/IR/RS-232/
Bidirectional PoE
Operation Manual
Operation Manual
DRAFT
DRAFT
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2012 by Cypress Technology.
All Rights Reserved.
Version 1.0 December 2012
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
DRAFT
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 07/12/12 Preliminary Released
DRAFT
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Transmitter Front and Rear Panels..3
6.2 Receiver Front and Rear Panels .....4
6.3. IR Cable Pin Assignment.................5
6.4. D-Sub 9 Pin Denitions ....................5
7. Connection Diagram ............................ 6
8. Specications ........................................ 7
9. Acronyms ............................................... 8
DRAFT
1
1. INTRODUCTION
The HDMI with RS-232 over Single CAT5e/6 transmitter and receiver set
can send uncompressed audio/video over a single run of CAT5e/6
cable up to 100 m with PoE feature and the added benet of control
through the built-in RS-232 and IR ports and a bi-directional LAN
connection.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1×HDMI to CAT5e/6 (with LAN/IR/RS-232/Bidirectionlal PoE)
Transmitter
• 1×CAT5e/6 to HDMI (with LAN/IR/RS-232/Bidirectionlal PoE) Reciever
• 1×IR Blaster
• 1×IR Receiver
• 1×24 V/1.25 A DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
Input HDMI source equipment such as DVD/Blu-ray player and HDMI
equipped output display (TV or monitor).
DRAFT
2
5. FEATURES
• HDMI 1.4 with 3D, 4k×2k support, HDCP & DVI Compliant
• Supports CEC bypass
• Simultaneous transmission of uncompressed data over a single
100 m/328 ft CAT5e/6 cable
• Uncompressed video 1080p, 60 Hz, 36-bit
• Audio support up to 7.1CH & Dolby TrueHD, DTS-HD
• 5Play™ convergence: HDMI, LAN, Bidirectionlal PoE & Control
(IR & RS-232)
• Installation Friendly
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
with cables of a different specication.
2. The PoE function is designed for powering compatible receiver
units only—non-PoE receivers will need their own power supply.
Receivers of another brand may not be compatible.
DRAFT
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
RearFront
RS-232 In
LAN
HDMI In
HDMI to CAT5e/6 with LAN/IR/RS232
Transmitter
CAT5e/6 Out
Link
IR2 Extender
IR1 Blaster
DC 24V
Power
2 31 64 7 8 95
1HDMI In: Connect to HDMI source equipment such as a DVD or Blu-
ray player.
2LAN: Connect to an internet or network connection.
3RS-232 In: Connect to a PC or laptop with D-Sub 9 pin male cable
for the transmission of RS-232 commands.
4Power LED: This blue LED will illuminate when the device is
connected to a power supply.
5DC 24V: Plug the 24 V DC power supply into the unit and connect
the adaptor to an AC outlet. Only one side of power needs to be
connected to activate both transmitter and receiver.
6IR 1 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line-of-sight of the
equipment to be controlled.
7IR 2 Extender: Connect to the supplied IR receiver cables for IR
signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR extender.
8Link LED: The yellow LED will illuminate when both the input and
output signals are connected.
9CAT5e/6 Out: Connect to the reciever unit with a Single CAT5e/6
cable for tranmission of all data signals.
DRAFT
4
6.2 Receiver Front and Rear Panels
RS-232 Out
LAN
HDMI Out
CAT5e/6 to HDMI with LAN/IR/RS232
Receiver
RearFront
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
DC 24V
2 31 74 8 965
1HDMI Out: Connect to a HDMI equipped TV/monitor for display of
the HDMI input source signal.
2LAN: Connect to a PC or Laptop to the Internet or network
connection.
3RS-232 Out: Connect to the device that is to be controlled (via
D-Sub 9 pin female cable) by RS-232 commands.
4Power LED: This blue LED will illuminate when the device is
connected to a power supply.
5DC 24V: Plug the 24 V DC power supply into the unit and connect
the adaptor to an AC outlet. Only one side of power needs to be
connected to activate both transmitter and receiver.
6IR 2 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line of sight of the
equipment to be controlled.
7IR 1 Extender: Connect to the supplied IR receiver cables for IR
signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR extender.
8Link LED: The yellow LED will illuminate when both the input and
output signals are connected.
9CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6
cable for tranmission of all data signals.
DRAFT
5
6.3. IR Cable Pin Assignment
3
1
2
3
1
2
Power 5 V
IR Blaster Signal
NC
IR Signal
Power 5 V
Grounding
IR Receiver
IR Blaster
6.4. D-Sub 9 Pin Denitions
Pin Dene TX / RX
1 N/C
2TxD / RxD
3RxD / TxD
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C
Tabla de contenidos
Otros manuales de Transmisor de CYP
CYP
CYP CH-A320TX Manual de usuario
CYP
CYP CH-1527TXPLV Manual de usuario
CYP
CYP PU-514LTX-1H Manual de usuario
CYP
CYP CH-2538TXM-TB Manual de usuario
CYP
CYP CPLUS-12FTX Manual de usuario
CYP
CYP CSI-8H8CVTX Manual de usuario
CYP
CYP AVIP-P5104T-B1C Manual de usuario
CYP
CYP CH-507TXWPUS Manual de usuario
CYP
CYP VEX-X1102T-B0C Manual de usuario
CYP
CYP CH-103TX Manual de usuario
CYP
CYP PUV-3050TX-UA Manual de usuario
CYP
CYP PU-1109 Manual de usuario
CYP
CYP AVX-101F-TX Manual de usuario
CYP
CYP CH-306TXA & RXA Manual de usuario
CYP
CYP CH-516TXAS Manual de usuario
CYP
CYP CH-107TX Manual de usuario
CYP
CYP PU-8H8CTXIR Manual de usuario
CYP
CYP CH-352TX Manual de usuario
CYP
CYP PUV-3090TX-UEA Manual de usuario
CYP
CYP CH-1602TXR Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
