CYP PU-IR01 Manual de usuario
OPERATION MANUAL
PU-IR01
Infra red over CAT5/6 extender
set
Table of Contents
1. Introduction 1
2. Features 1
3. Package Contents 1
4. Operation Controls and Functions 2
4.1 Front Panel Diagram 2
4.2 Rear Panel Diagram 3
5. Connection Diagram 4
6. Specications 4
Page 1
1. Introduction
The IR Extender and the Repeater set is perfect for controlling IR controlled source
equipment over long distances. Up to ve sources can be controlled using this
extender set. Two sources can be controlled located locally to the repeater, whilst
the remaining three sources can be controlled locally to the extender, which can be
located up to 250m away via CAT5/6 cable. This system allows for the sources to be
controlled by their own original remote controls, from extended distances. A 5-eye
emitter accessory can be supplied for additional control of extra source equipment.
2. Features
• Supports ve outputs (two from the repeater, three from the extender).
• Control source equipment from a distance of up to 250 metres away, via
CAT5/6 cable.
• Transmits infrared signals only.
• Allows the use of existing remote controls.
• IR Receiver’s frequency is at 20~60 kHz.
3. Package Contents
• Infrared Extender Box (CIR-03)
• Infrared Repeater Box (CIR-12)
• 1pc IR Eye Receiver cable (CIR-12)
• 5pcs IR Eye blaster cables (3pcs for CIR-03, 2pcs for CIR-12)
• 2pcs 5V DC power supply adaptors
• Operation Manual
Page 2
4. Operation Controls and Functions
4.1 Front Panel
1. IR OUT1, 2 and 3: Connect your IR Eye Blaster cables to control source equipment.
2. IR IN: Connect to IR Eye receiver cable in order to receive IR remote control signals.
3. Note:
1. Please be careful when plugging in the blaster and receiver cables as a wrong
connection will result in a cable and device overload.
IR OUT1
CIR-03 IR Extender
IR OUT2 IR OUT3 IR IN
CIR-12 IR Repeater
IR OUT1 IR OUT2
1 2 3
Page 3
4.2 Rear Panel
1. IR CAT5: Connect the CAT 5 cable to Infrared Extender Box with IR receiver.
2. Power: Plug the 5VDC power supply into the unit and connect the adaptor to an
AC outlet.
Note:
1. Only a power adapter is needed, connect the power adapter on either the CIR-
03 or CIR-12.
1 2
IR CAT5
DC 5V
Page 4
5. Connection Diagram
6. Specications
Input Port
1 x IR Jack
1 x CAT5/6
Output Port
2 x IR Jack, 1 x CAT5/6
3 x IR Jack
Power Supply 5V/1A DC (both units the same)
Dimensions (mm) 60(W) x 50(D) x 25(H)
Weight (g) Repeater: 260, Extender: 140
Chassis Material Aluminium
Silk Skin Colour Black
Operating Temperature Operating from 0°C ~ 40°C
Tabla de contenidos
Otros manuales de Extensor de CYP
CYP
CYP CH-506TX Manual de usuario
CYP
CYP CH-1601TXRX Manual de usuario
CYP
CYP CH-1529TXPL Manual de usuario
CYP
CYP CH-514TXL Manual de usuario
CYP
CYP CH-513TXL Manual de usuario
CYP
CYP PU-USBX Manual de usuario
CYP
CYP PU-1103 Manual de usuario
CYP
CYP Suprex SPX-7400 Series Manual de usuario
CYP
CYP PU-1107-KIT Manual de usuario
CYP
CYP PU-513L-KIT Manual de usuario
CYP
CYP PU-HBTPL-ZE Manual de usuario
CYP
CYP PU-506-KIT Manual de usuario
CYP
CYP PU-506-KIT Manual de usuario
CYP
CYP CH-110TX Manual de usuario
CYP
CYP CIR-03 Manual de usuario
CYP
CYP CH-1106TX & RX Manual de usuario
CYP
CYP CH-506TX Manual de usuario
CYP
CYP PU-USBX Manual de usuario
CYP
CYP CH-710TX Manual de usuario
CYP
CYP SDV-FTX Manual de usuario
