CyberData 011403 Manual de usuario
Quick Start Guide 931975A
The IP Endpoint Company
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operations Guide,
which is available in the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011403/
Note You can also navigate to the Downloads tab by going to
www.CyberData.net and following the steps that are indicated by
the following figures:
2.0 Select Power Source
IEEE 802.3af or 802.3at PoE Switch IEEE 802.3af or 802.3at PoE Injector
Set PoE power type to Class 0 = 15.4Wa
OR
for high power PoE+ set Class 4 = 30W
a. The 15.4W power connection will limit the maximum dB/SPL output.
Therefore, if the maximum volume is desired, you should target the 802.3at
(30W) level.
CAT6 cable recommended—
for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
011403 INFORMACAST ENABLED
PAGING AMPLIFIER
1
3
2
OUR PRODUCTS
VOIP PRODUCTS
A
B
Downloads
INFORMACAST ENABLED
C
InformaCast Enabled Paging Amplifier
Quick Start Guide
Quick Start Guide 931975A
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of
the device during the initialization process. See the following figure:
3.2. The Power (Pwr) LED is GREEN for 802.3af and is BLUE for 802.3at. The
GREEN Status LED and the GREEN Power (Pwr) LED come on
immediately. The Link/Network Activity LED blinks to indicate network
traffic.
After about 20 seconds the GREEN Status LED will blink twice to indicate
that the board is fully booted.
If there is no DHCP server available on the network, it will try 12 times with a
three second delay between tries and eventually fall back to the
programmed static IP address (by default 192.168.1.23). This process will
take approximately 80 seconds.
3.3. When the device has completed the initialization process, press and hold
the RTFM switch for 3 seconds to announce the IP address.
This concludes the power test. Go to Section 4.0, "InformaCast
Configuration File Retrieval".
Power
Link / Act. Status
Power (Pwr) LED
(BLUE/GREEN)
Link/Network Activity (Link/Act.) LED
(GREEN)
Status LED
(GREEN)
Quick Start Guide 931975A
4.0 InformaCast Configuration File Retrieval
4.1. DHCP should be enabled. After the device initializes, it will send a
broadcast to the DHCP server to ask for the location of its
InformaCastSpeaker.cfg configuration file.
4.2. SLP or TFTP?
•SLP should be enabled on InformaCast version 5.0.4 or higher. SLP is an
InformaCast protocol introduced in InformaCast version 5.0.4. The device
will retrieve its configuration file from an InformaCast server folder
specified by SLP. SLP method is preferred.
•TFTP servers may be used instead of SLP. In this alternate scenario,
DHCP option 150 is required to provide the device with the address of the
TFTP server. Otherwise, the device will be unable to retrieve its
configuration file.
Note The device and InformaCast server should be on the same subnet
during the device's initial configuration if it cannot access the
VLANs upon which the InformaCast Server and DHCP servers are
located.
5.0 Identification and Testing
5.1. Ensure the InformaCast Server has detected a new device.
5.2. Test the newly detected device.
5.3. Add the newly detected device to the InformaCast Server.
Quick Start Guide 931975A
6.0 Contacting CyberData VoIP Technical Support
You are welcome to call CyberData VoIP Technical Support at 831-373-2601
x333.
We encourage you to access our Technical Support help desk at the following
address:
https://support.cyberdata.net/
Note You can also access the Technical Support help desk by going to
www.cyberdata.net and clicking on the SUPPORT menu.
The Technical Support help desk provides the options of accessing
documentation for your CyberData product, browsing the knowledge base, and
submitting a troubleshooting ticket.
Please be advised requests for Returned Materials Authorization (RMA) numbers
require an active VoIP Technical Support ticket number. A product will not be
accepted for return without an approved RMA number.
Otros manuales para 011403
2
Tabla de contenidos
Otros manuales de Amplificador de CyberData
CyberData
CyberData Part #010861 930106D Manual de usuario
CyberData
CyberData 011579 Manual de usuario
CyberData
CyberData VoIP V2 Manual de usuario
CyberData
CyberData Syn-Apps 011413 Manual
CyberData
CyberData 011403 Manual
CyberData
CyberData 11097 Manual
CyberData
CyberData VoIP Paging/Loudspeaker Amplifier Manual de usuario
CyberData
CyberData 11097 Manual de usuario
CyberData
CyberData 11114 Manual
CyberData
CyberData 011404 Manual de usuario
CyberData
CyberData VoIP Loudspeaker Amplifier Part #010859 Manual de usuario
CyberData
CyberData 11095 Manual de usuario
CyberData
CyberData 11114 Manual de usuario
CyberData
CyberData 11115 Manual de usuario
CyberData
CyberData InformaCast Enabled 011407 Manual de usuario
CyberData
CyberData 11061 Manual de usuario
CyberData
CyberData 11096 Manual de usuario
CyberData
CyberData 011579 Manual
CyberData
CyberData InformaCast Enabled 011407 Manual de usuario
CyberData
CyberData 011405 Manual
