CyberData VoIP V2 Manual de usuario
Quick Start Guide 930459D
The IP Endpoint Company
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operation Guide,
which is available on the Documentation page at the following website
address:
http://www.cyberdata.net/products/voip/digitalanalog/loudspeakerampv2/docs.html
Note You can also navigate to the Documentation page by going to
www.CyberData.net and following the steps that are indicated by
the following figures:
2.0 Select Power Source
Note For PoE powered, place DIP Switches 1and 4to OFF and place DIP Switch 3
to ON.
PoE Switch PoE Injector
Set PoE power type to Class 0 = 13W
CAT6 cable recommended—
for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
12
3
VoIP V2 Loudspeaker Amplifier
Quick Start Guide (AC-Powered)
Quick Start Guide 930459D
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of
the device. See the following figure:
3.2. The GREEN power and status LEDs and the YELLOW link LED come on
immediately. The activity LED illuminates GREEN for a 10Mb link or
YELLOW/GREEN for a 100MB when the network link to the Paging
Amplifier is established. The activity LED blinks to indicate network traffic.
After about 27 seconds, the GREEN status LED will blink twice to indicate
that the amplifier is fully booted.
If there is no DHCP server available on the network, it will try 12 times with a
three second delay between tries and eventually fall back to the
programmed static IP address (by default 10.10.10.10). This process will
take approximately 80 seconds.
3.3. When the device has completed the initialization process, press and hold
the RTFM switch for 3 seconds to announce the IP address.
This concludes the power test. Go to Section 4.0, "Connecting to a Network
in a Test Environment".
Activity LED (GREEN)
Link LED (GREEN/YELLOW)
Quick Start Guide 930459D
4.0 Connecting to a Network in a Test Environment
Note The following connections are usually needed for this procedure:
• Computer
• PoE switch or injector
• CyberData device
4.1. In a test environment, use a computer that is connected to the same switch
as a single CyberData device. Note the subnet of the test computer.
4.2. Use the CyberData Discovery Utility program to locate the device on the
network. You can download the Discovery Utility program from the following
website address:
http://www.cyberdata.net/support/voip/discovery.html
4.3. Wait for initialization to complete before using the Discovery Utility program
to scan for a device. The device will show the current IP address, MAC
address, and serial number.
4.4. Select the device.
4.5. Click Launch Browser. If the IP address is in a reachable subnet from the
computer that you are using to access the device, the Discovery Utility
program should be able to launch a browser window pointing to the device’s
IP address.
4.6. Log on to the web interface by using the default username (admin) and
password (admin) to configure the device.
4.7. Perform an audio test by pressing the Test Audio button that is located at
the bottom of the Device Configuration page. If the audio test message is
clearly audible, then your CyberData device is functioning properly.
4.8. The device is now ready to be set for your desired network configuration.
You may search the Compatible IP-PBX Servers index for available
sample VoIP phone system configurations and set up guides at the following
website address:
http://www.cyberdata.net/support/server/index.html
Quick Start Guide 930459D
5.0 Contacting CyberData VoIP Technical Support
Please visit our website and complete the Contact VoIP Tech Support form
available at the following website address:
http://www.cyberdata.net/support/contactsupportvoip.php
Note You can also navigate through menus to the Support form by going to
www.CyberData.net as shown in the following figure:
The Contact VoIP Tech Support form initiates a ticket which CyberData uses for
tracking. Most importantly, the Contact VoIP Tech Support form tells us which
PBX system and software version that you are using, the make and model of the
switch, and other essential troubleshooting information. Please also include as
much detail as possible in the Describe Problem section of the Support form.
Requests for Returned Materials Authorization (RMA) numbers require an active
VoIP Technical Support ticket number. A product will not be accepted for return
without an approved RMA number.
More information about warranty and RMA returns is available at the following
website address:
http://www.cyberdata.net/support/warranty/index.html
Otros manuales para VoIP V2
5
Tabla de contenidos
Otros manuales de Amplificador de CyberData
CyberData
CyberData InformaCast Enabled 011407 Manual de usuario
CyberData
CyberData 11114 Manual
CyberData
CyberData 11097 Manual de usuario
CyberData
CyberData 11114 Manual de usuario
CyberData
CyberData VoIP Paging/Loudspeaker Amplifier Manual de usuario
CyberData
CyberData 011403 Manual de usuario
CyberData
CyberData InformaCast Enabled 011407 Manual de usuario
CyberData
CyberData 011403 Manual
CyberData
CyberData 011085 Manual de usuario
CyberData
CyberData 11085 Manual de usuario
CyberData
CyberData 011324 Manual de usuario
CyberData
CyberData 10965 Manual de usuario
CyberData
CyberData 11061 Manual de usuario
CyberData
CyberData 011579 Manual de usuario
CyberData
CyberData InformaCast Enabled 011407 Manual
CyberData
CyberData InformaCast Enabled 011407 Manual de usuario
CyberData
CyberData 11097 Manual de usuario
CyberData
CyberData 11097 Manual de usuario
CyberData
CyberData 11097 Manual
CyberData
CyberData 11115 Manual
