Curt Manufacturing 58987 Manual de usuario

58987-INS-RA •04/20/2021 •ECN8140 •PAGE 1 OF 4

INSTALLATION MANUAL

Tools Required

Drill Fishwire

Drill bit, 3/32" Electrical tape

Panel trim

removal tool

Cutting tool

Wiring Location(s)

Product Photo

WARNING

Do not exceed product rating or tow vehicle lamp load rating, whichever is lower.

Maintenance

Periodic inspection of all wires and connections should be performed

to ensure there is no visible damage or loose connections.

Wiring Location Guide*

for Trucks (T)

T1 Behind driver side taillight housing

T2 Behind passenger side taillight housing

T3 Behind driver side rear bumper

T4 Behind center of rear bumper fascia

T5 Behind passenger side rear bumper

T4 T5

* Representative vehicle shown

NOTICE

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

All steps must be followed to ensure the product will function properly. Once installed,

test for proper function by using a test light or connecting a properly wired trailer.

Level of Difficulty

Easy

Installation difficulty levels are based on time

and effort involved and may vary depending on

the installer level of expertise, condition of the

vehicle and proper tools and equipment.

58987-INS-RA •04/20/2021 •ECN8140 •PAGE 2 OF 4

Step 1

Locate the vehicle battery and

disconnect the negative battery terminal.

Note: Some vehicles may have a second

battery. Remove this terminal also.

Be sure to fasten this wire down

and away from the battery while

completing the installation process

Step 2

Starting at the rear of the passenger side of

the vehicle, on the inside frame rail, locate the

taillight vehicle connectors. The connectors will

be similar to those on your new custom wiring

product. Separate the connectors from the

taillight housing taking care not to damage the

locking tabs.

Insert the custom wiring end with yellow wire

between the separated connectors. Make sure

the connectors are fully inserted with locking

tabs in place. Loosely zip tie in place.

Step 3

Locate a grounding point such as an existing screw or bolt in the frame of the

vehicle or drill a 3/32"pilot hole. The area should be free from rust, dirt, and paint

(abrasive pad/paper to remove rust and paint). Secure the white ground wire with

the ring terminal on the existing fastener or with the provided ground screw.

CAUTION

Check for miscellaneous items that may be hidden behind or under

any surface before drilling to avoid damage and/or personal injury

NOTICE

Once the custom wiring harness is installed, verify that the harness is functioning

by attaching the 4-flat to any vehicle with functioning trailer lights. The taillights

on the tow vehicle should function along with the taillights on the towing vehicle.

58987-INS-RA •04/20/2021 •ECN8140 •PAGE 3 OF 4

Step 4

On the passenger side of the vehicle, route

the 4-flat along the and above the fame rail

up to the rear of the passenger-side front tire.

Step 5

Using a ﬁshwire, route it down along the inner

fender and outer fender. From under the vehicle,

pull back the inside of the wheel well lining until

you see the ﬁshwire. Feed the 4-ﬂat wire up into

the engine compartment using the ﬁshwire.

How to Fishwire

A) Fish wire is a way to push or pull

an electrical wire through a blind hole.

Make sure the wire is long enough

to stick out on the other side.

Insert the fish wire through the blind

hole and locate it on the other side.

B) Use tape to secure the harness

to the fish wire and pull back up.

The fish wire or harness may get hung up on

something, if this happens you may have to

push back down, wiggle it around or twist the

wire to loosen it from what it's hung up on.

Fish wire could be anything from a cut-up wire

hanger, stiff wire, rope or string depending on

what is needed for the installation.

A A

58987-INS-RA •04/20/2021 •ECN8140 •PAGE 4 OF 4

Step 6

Route the 4-flat along the passenger-side

inner fender to the front of the truck.

Step 7

Secure any excess wire so that it is not drooping or dangling, but not so tight that

it causes unnecessary strain to the wire which could lead to breakage over time.

After removing slack from the 4-flat wire, tighten any zip ties and add as needed.

Use a zip tie to fasten any excess wire to a solid spot along the driver-side inner fender.

Reinstall all items removed during install. If it was disconnected at the beginning of the installation,

reconnect the negative battery terminal. Install the provided 4-ﬂat dust cover to help prevent corrosion.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Curt Manufacturing

Curt Manufacturing

Curt Manufacturing 16600 Manual de usuario

Curt Manufacturing

Curt Manufacturing 16320 Manual de usuario

Curt Manufacturing

Curt Manufacturing CHT-56438 Manual de usuario

Curt Manufacturing

Curt Manufacturing 3025104 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13203 Manual de usuario

Curt Manufacturing

Curt Manufacturing 58957 Manual de usuario

Curt Manufacturing

Curt Manufacturing 15809 Manual de usuario

Curt Manufacturing

Curt Manufacturing 2060 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18412 Manual de usuario

Curt Manufacturing

Curt Manufacturing 56218 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13364 Manual de usuario

Curt Manufacturing

Curt Manufacturing 16050 Manual de usuario

Curt Manufacturing

Curt Manufacturing 70001 Manual de usuario

Curt Manufacturing

Curt Manufacturing RockerBall 40047 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13454 Manual de usuario

Curt Manufacturing

Curt Manufacturing 11435 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13081 Manual de usuario

Curt Manufacturing

Curt Manufacturing 45950 Manual de usuario

Curt Manufacturing

Curt Manufacturing 12070 Manual de usuario

Curt Manufacturing

Curt Manufacturing Quick Goose II Manual de usuario

Curt Manufacturing

Curt Manufacturing 56436 Manual de usuario

Curt Manufacturing

Curt Manufacturing DISCOVERY Manual de usuario

Curt Manufacturing

Curt Manufacturing 18009 Manual de usuario

Curt Manufacturing

Curt Manufacturing 4501 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario