Curt Manufacturing 56165 Manual de usuario

INSTALLATION INSTRUCTIONS

CUSTOM WIRING HARNESS

WIRING LOCATION GUIDEAPPLICATIONS

NOTICE

WARNING

TOOLS NEEDED

Signal Circuits - 3.0 amps per side

Tail / Running Circuits - 6.0 amps total

Check vehicle owner's manual or contact

the vehicle manufacturer for more information.

Ratchet

10mm socket

Phillips screwdriver

Panel trim removal tool

The battery connection must be fuse-protected, 10-amp max.

Exceeding the product rating can cause loss of warranty,

overheating and potential fire. Do not exceed product rating

or tow vehicle lamp load rating, whichever is lower.

Make Model

Toyota Rav4

WARNING: DO NOT EXCEED PRODUCT RATING OR TOW VEHICLE LAMP LOAD RATING, WHICHEVER IS LOWER

SUVS, MINI & FULL-SIZED VANS (S)

Representative vehicle shown below

S3 - Behind driver side rear access panel

S4 - Behind passenger side rear access panel

S3 S4

All steps must be followed to ensure the wiring harness

will function properly. Once installed, test for proper function

by using a test light or connecting a properly wired trailer.

PAGE 1 • 56165-INS-RB

A B C

Step 1

Open the vehicle tailgate. Remove the rear scuff panel, trunk

floor coverings, storage covers and the privacy screen (A,B).

Step 2

On both sides, remove all trim fasteners and slightly pull

out on the rear trim panels to locate the vehicle taillight wiring

harness connectors. The connectors will be similar to those on

the custom wiring harness C,D).

Step 3

Starting on the driver side, separate the connectors from the

taillight housing taking care not to damage the locking tabs.

Step 4

Insert the custom wiring harness end with yellow wire

between the separated connectors. Make sure the

connectors are fully inserted with locking tabs in place.

Step 5

Locate a suitable grounding point near the connector such as

an existing screw with nut in the vehicle frame or drill a 3/32"

pilot hole for the provided screw. The area should be free of

rust, dirt and paint. Secure the white ground wire using the ring

terminal and provided screw.

WARNING: Check for miscellaneous items that may be

hidden behind or under any surface before drilling to avoid

damage and / or personal injury.

Step 6

Route the custom wiring harness end with the green wire to the

passenger side behind the removed scuff panel. Repeat steps

3 and 4 on the passenger side using the harness end with the

green wire.

Step 7

Route the black power wire from the vehicle battery

as shown on the included CME-PCL-INS sheet.

Step 8

Locate a flat spot inside the vehicle, near the taillight. Adhere

the black converter box using the provided double-sided tape.

Step 9

When in use, route the 4-flat to the center of the vehicle. When

not in use, roll up and store in a convenient, out of the way

location. Secure any loose wires with the provided cable ties.

Step 10

Reinstall all items removed during install. Install the

provided 4-flat dust cover to help prevent corrosion.

INSTALLATION /SAFETY INSTRUCTIONS

56165-INS-RB • PAGE 2

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Curt Manufacturing

Curt Manufacturing

Curt Manufacturing 11065 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13118 Manual de usuario

Curt Manufacturing

Curt Manufacturing 70112 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13333 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18412 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18153 Manual de usuario

Curt Manufacturing

Curt Manufacturing LIPPERT 18109 Manual de usuario

Curt Manufacturing

Curt Manufacturing DISCOVERY Manual de usuario

Curt Manufacturing

Curt Manufacturing 45950 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18035 Manual de usuario

Curt Manufacturing

Curt Manufacturing 56436 Manual de usuario

Curt Manufacturing

Curt Manufacturing 3025104 Manual de usuario

Curt Manufacturing

Curt Manufacturing A25 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13364 Manual de usuario

Curt Manufacturing

Curt Manufacturing 12070 Manual de usuario

Curt Manufacturing

Curt Manufacturing 51451 Manual de usuario

Curt Manufacturing

Curt Manufacturing ECHO Manual de usuario

Curt Manufacturing

Curt Manufacturing 18100 Manual del operador

Curt Manufacturing

Curt Manufacturing 70001 Manual de usuario

Curt Manufacturing

Curt Manufacturing 70103 Manual de usuario

Curt Manufacturing

Curt Manufacturing RockerBall 40047 Manual de usuario

Curt Manufacturing

Curt Manufacturing 56218 Manual de usuario

Curt Manufacturing

Curt Manufacturing 16050 Manual de usuario

Curt Manufacturing

Curt Manufacturing 4516 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario