Curt Manufacturing 55525 Manual de usuario

INSTALLATION INSTRUCTIONS

CUSTOM WIRING HARNESS

WIRING LOCATION GUIDEAPPLICATIONS

NOTICE

WARNING

TOOLS NEEDED

Signal Circuits - 2.1 amps per side

Tail / Running Circuits - 4.2 amps total

Check vehicle owner's manual or contact

the vehicle manufacturer for more information.

Phillips screwdriver

Flat blade screwdriver

Panel trim removal tool

The battery connection must be fuse-protected, 10-amp max.

Exceeding the product rating can cause loss of warranty,

overheating and potential fire. Do not exceed product rating

or tow vehicle lamp load rating, whichever is lower.

Make Model

Ford Windstar

WARNING: DO NOT EXCEED PRODUCT RATING OR TOW VEHICLE LAMP LOAD RATING, WHICHEVER IS LOWER

SUVS, MINI & FULL-SIZED VANS (S)

Representative vehicle shown below

S1 - Behind driver side taillight housing

S2 - Behind passenger side taillight housing

S1 S2

All steps must be followed to ensure the wiring harness

will function properly. Once installed, test for proper function

by using a test light or connecting a properly wired trailer.

PAGE 1 • 55525-INS-RB

A B C

D E

Step 1

Open the tailgate and remove the vehicle taillight

assemblies by removing the screws and carefully

prying the taillight away from the vehicle (A).

CAUTION: Pry the taillights at

the indicated points to avoid damage.

Step 2

Remove the fasteners securing the rear scuff panel. Remove

the scuff panel by pulling out on the bottom and then up (B).

Take care not to damage the alignment tabs on the back.

Step 3

Remove the trim panel to locate the vehicle taillight wiring

harness connectors (C,D). The connectors will be similar to

those on the custom wiring harness. Separate the connectors

from the taillight housing taking care not to damage the locking

tabs.

Step 4

Beginning on the driver side, disconnect the top,

grey connector from the taillight assembly (E). Insert

the custom wiring harness end with the yellow wire

between the separated connectors. Make sure the

connectors are fully inserted with locking tabs in place.

Step 5

Route the remainder of the custom wiring harness to the

passenger side. At the same time push the yellow wire

in between the bumper fascia and the vehicle body.

Step 6

On the passenger side, disconnect the middle, black connector

and insert the custom wiring harness end with the red and

brown wires between the separated connectors. Make sure that

the connectors are fully inserted with locking tabs in place.

Step 7

Disconnect the top, grey connector from the taillight assembly

(E), and insert the custom wiring harness end with the green &

red with white stripe wires between the separated connectors.

Make sure that the connectors are fully inserted with locking tabs

in place.

Step 8

Locate a suitable grounding point near the connector such as

an existing screw with nut in the vehicle frame or drill a 3/32"

pilot hole for the provided screw. The area should be free of

rust, dirt and paint. Secure the white ground wire using the ring

terminal and provided screw.

WARNING: Check for miscellaneous items that may

be hidden behind or under any surface before drilling to avoid

damage and / or personal injury.

INSTALLATION /SAFETY INSTRUCTIONS

55525-INS-RB • PAGE 2

1 2 3 4

F FFF

INSTALLATION /SAFETY INSTRUCTIONS

Step 9

Disconnect the negative battery cable. Using the

provided ring terminal, attach the fuse holder (with

the fuse removed) to the positive battery terminal.

Step 10

Connect the fuse holder to the black, 12 gauge wire using

the provided yellow butt connector. Route the wire rearward

from the fuse holder, underneath the vehicle along the frame

rail, to the bumper. End at the passenger-side taillight.

WARNING: Make sure to avoid areas that contain moving

parts that could cut, pinch or burn the wires when routing the 4-flat

harness to the rear of the vehicle. Failure to follow these warnings

may cause property damage, personal injury or loss of life.

Step 11

Attach the 12 gauge wire to the blue wire on the

custom wiring harness marked "Battery +" with

the provided yellow butt connector.

Step 12

Open the jack storage compartment cover. From the

outside of the vehicle, pull the rubber grommet surrounding

the passenger-side wiring harness away from the body.

Carefully slit the grommet to allow the wiring harness 4-flat

connector and wires to pass through the grommet and into

the jack storage compartment. Reseat the grommet into the

mounting hole. Retain the 4-flat connector inside the jack

storage compartment for future use. Use the provided sealant

to seal the cut in the grommet and around all the wires (F,G).

Step 13

Reconnect the negative battery cable

and install the provided 10 amp fuse.

Step 14

Locate a flat clean surface that is out of the path of spray

and debris from the rear wheels and road. Adhere the black

converter box using the provided double-sided tape. Failure to

mount the box in a protected area can cause loss of warranty,

product failure, overheating and potential fire.

WARNING: Check for miscellaneous items that may

be hidden behind or under any surface before drilling to avoid

damage and / or personal injury.

Step 15

Reinstall all items removed during install. Install the

provided 4-flat dust cover to help prevent corrosion.

PAGE 3 • 55525-INS-RB

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Curt Manufacturing

Curt Manufacturing

Curt Manufacturing 18101 Manual del operador

Curt Manufacturing

Curt Manufacturing LIPPERT 18109 Manual de usuario

Curt Manufacturing

Curt Manufacturing 3025104 Manual de usuario

Curt Manufacturing

Curt Manufacturing CHT-56438 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18009 Manual de usuario

Curt Manufacturing

Curt Manufacturing 12113 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18412 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18153 Manual de usuario

Curt Manufacturing

Curt Manufacturing 16600 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18035 Manual de usuario

Curt Manufacturing

Curt Manufacturing 11435 Manual de usuario

Curt Manufacturing

Curt Manufacturing ECHO Manual de usuario

Curt Manufacturing

Curt Manufacturing 56165 Manual de usuario

Curt Manufacturing

Curt Manufacturing 13454 Manual de usuario

Curt Manufacturing

Curt Manufacturing 56446 Manual de usuario

Curt Manufacturing

Curt Manufacturing 18100 Manual del operador

Curt Manufacturing

Curt Manufacturing 11419 Manual de usuario

Curt Manufacturing

Curt Manufacturing 16320 Manual de usuario

Curt Manufacturing

Curt Manufacturing DISCOVERY Manual de usuario

Curt Manufacturing

Curt Manufacturing 12170 Manual de usuario

Curt Manufacturing

Curt Manufacturing 58963 Manual de usuario

Curt Manufacturing

Curt Manufacturing 45950 Manual de usuario

Curt Manufacturing

Curt Manufacturing 16050 Manual de usuario

Curt Manufacturing

Curt Manufacturing ECHO Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario