Cub VS-95A043 Instrucciones de instalación y funcionamiento
b
VS-95A043
For Passenger Cars
Blind Spot Detection I Lane Change Alert
1
1. Precautions ......................................................................................................... 2
2. Introduction ........................................................................................................ 5
2.1 System block ................................................................................................................ 5
2.2 Product specications ......................................................................................... 5
3. Installation Guide .................................................................................... 6
3.1 Installation diagram ............................................................................................... 6
3.2 Package contents ................................................................................................... 6
3.3 Installation steps ....................................................................................................... 7
3.4 Reinstallation ............................................................................................................... 9
4. User Manual ....................................................................................................... 10
4.1 System startup and shut o .......................................................................... 10
4.1.1 System startup ........................................................................................................... 10
4.1.2 System shut o .......................................................................................................... 10
4.2 Function ............................................................................................................................. 10
4.2.1 Detection zone ........................................................................................................... 11
4.2.2 Blind Spot Detection (BSD) .......................................................................... 11
4.2.3 Lane Change Alert (LCA) ..................................................................... 11
4.3 System abnormalities .......................................................................................... 12
4.3.1 Malfunction prompts ............................................................................................. 12
4.3.2 Troubleshooting ........................................................................................................ 12
Contents
2
1Blind Spot Detection System
Precautions
Before using this device, please read this instruction
manual carefully before installing or removing it to
ensure that the device is safe to use. The Company
shall not be liable for any damage arising from failure
to comply with the following matters.
Before installing
If you wish to laminate your car’s rear windshield with or it has
already laminated with a heat insulation film, please contact the
dealer to ensure that the heat insulation film does not technically
contain metal components. If it contains the metal components, it is
recommended not to install this device.
If your car has the following conditions, please consult a professional
technician to evaluate whether or not to install this device：
• If the angle between the rear windshield and the horizon is not
within 20 - 60 degrees, it is recommended not to install this device.
• If the third brake light is on top of the interior rear windshield, it
may aect the radar installation position.
• If there is a rear spoiler, rear spare tire, or a bicycle, it may block
the radar and aect the system performance.
Due to the highly sensitive detection performance of this device,
please ensure to follow the installation procedures and precautions
during installation to avoid affecting the device performance, and
please ensure to hide the wires properly according to the layout of
the car to avoid the wiring harness from aecting driving safety, and
obstructing you from getting in and o the car. It is recommended that
you consult a professional technician for installation.
Please follow the preparatory works before installation：
Please wear protective
goggles.
Please work with an
assistant.
Please tighten with
a specified torque.
wrench
(1)
(2)
(3)
(4)
3
If the connector is
dislocated, please
replace the connector
to its original position.
Please do not pull the
connector apart by
pulling the harness.
Please do not pull
the harness by force.
Connect the connector
and terminal tightly.
Cut o the excessive
length of the cable tie.
RF Standard
(1)
(2)
NCC low-power radio waves radiated device management methods：
Companies, stores, or users are prohibited from changing
the frequency, increasing the power, or modifying the
characteristics and functions of the original design of the
certified low-power radio waves radiated device without
permission.
The use of low-power RF devices must not affect the
safety of aviation and interfere with legal communications.
If any interference occurs, they should be stopped
immediately and improved to the extent of no interference
before users can use the legal communications mentioned
in the previous paragraph, i.e., radio communications
under the provisions of the Telecommunications Act. Low-
power RF devices must endure interference from legal
communications or industrial, scientic, and medical radio
wave-radiated electrical equipment.
Article 12:
Article 14:
FCC regulations：
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including
interference that may cause undesired operation.
4
NOTE : This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more
of the following measures :
━Reorient or relocate the receiving antenna.
━Increase the separation between the equipment and receiver.
━Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
━Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user΄s authority to operate the
equipment.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and a
human body.
Although the device provides blind spot detection assistance
warning function, it might still be affected by multiple factors
such as road conditions, driver behaviors, driving environment
or weather which may result in occasional false alarm/no alarm.
Therefore, the device does not guarantee 100 % detection accuracy
rate. Do not over-rely on the device for avoidance of accidents, and
you shall at all times follow the traffic rules, pay attention to the
actual road conditions, stay alert, drive carefully.
5
2Introduction
Blind Spot Detection System
Thank you for purchasing this device. The device uses a 77 GHz
millimeter-wave radar to detect vehicles coming behind your car. When
there is a car getting in the detection zone, the device will provide visual
and audible warnings to remind you to pay attention to the car in order to
protect the safety of the driver and passengers. If you have any problems
while using it, please contact your dealer.
Radar frequency 76-77 GHz
Operating temperature -40℃~ +85℃
Storage temperature -40℃~ +95℃
Input voltage 9~16 V
Current consumption 6 W (Max.)
Left turn signal wiring
Right turn signal wiring
Cigarette lighter plug
Left indicator
Right indicator
Buzzer
2-1 system block
2-2 Product Specifications
6
3
No. Item Q'ty
Radar with its bracket 1 set
Indicator 2 pcs
Buzzer 1 pcs
Main power harness 1 set
Accessories
(including 2 iron plates, 2 indicator adhesive
tapes, 15 cable ties, 4 crab clips, 1 manual)
1 bag
Blind Spot Detection System
Left turn signal
Radar
Right turn signal
Cigarette lighter plug
/ IGN WIRING
Left indicator
Right indicator
Buzzer
3-1 Installation diagram
3-2 Package contents
Installation Guide
7
3-3 Installation steps
Note: Please ensure that the heat insulation lm on the rear windshield
does not contain metal components.
Please prepare a tape measure, a multimeter and an alcohol pad before
installing.
1
10cm10cm
Radar installation position diagram
Center of rear windshield
Radar
Find a position ±10 cm at the center of the rear windshield's upper edge
with a tape measure, and wipe it with an alcohol pad.
Note 1:
There must not be any no-original object such as driving recorder,
brake light and other devices within 5 cm left and right of the radar.
If the third brake light is located at the center of the rear
windshield's upper edge, it is recommended to install the radar
beneath it with the distance at least 2 cm.
Note 2:
2
Tear off the tape on the radar's bracket, face the surface printed with
the logo Cub outwards, and attach the bracket parallel and close to the
ceiling or align along the defog line. Be careful not to attach it to the
defog line.
3
Flip down radar's level, adjust the bracket until the bubble in the level is
at the center of the two vertical black lines, and then tighten the knob.
8
4
5
6
After connecting the radar and main power harness, hide the wires along
with the ceiling to the C-pillar on the driver side, and connect the left
and right turn signal wirings to the car's left and right turn signal trigger
wires(+) with crab clips.
Note: Please ensure the positive
electrode of the left and right
turn signals by a multimeter.
Note: If the turn signals are
not connected, the system will
alarm by illuminating indicators
only.
Continue to hide the main power harness along with the ceiling or down
the door frame's waterproof strip to the driver side's A-pillar, connect the
indicators and buzzer, and hide the two wire harnesses into the door
rubber strip.
If there is a risk of airbags'interference when hiding harness, please hide
harness down the door frame's waterproof strip to the driver side' s A-pillar.
Attach the left indicators directly to the A-pillar at an appropriate visible
height, or attach it to an iron plate, insert it between the A-pillar and the
instrument panel, and then adjust the best viewing angle. Attach the
alarm buzzer at a position near the instrument panel.
Note: If the surface of the
A-pillar has a velvet cover, the
indicators will be unable to x
firmly. It is recommended to
install it with an iron plate.
9
9
7
8
3-4 Reinstallation
Right indicator goes to right side A-pillar through the left side A-pillar and
then the ceiling. The installation height and method is the same with the
left one.
Please ensure to hide all the wires properly into the trims and frame's
waterproof strips to avoid the wiring harness from aecting driving safety,
and obstructing you from getting in and o the car. Besides please hide
the splitter into the trim under the instrument panel properly and use
cable ties to x with the car cables.
Plug into Cigarette lighter and hide the remaining wires properly. When
ACC ON, the indicators will light up for 3 seconds, and the buzzer will
chime once, indicating that the system has started normally.
If the bracket is incidentally attached wrongly, such as not at the center
of the rear windshield, not close to the upper edge of the rear windshield,
or not maintained at a horizontal level, etc., and you wish to remove
and reattach, spray alcohol around the bracket base in contact with
rear windshield. Then use a thin line such as a shing line to scrape the
edges of the bottom back and forth.
Tabla de contenidos
