CTC Union SDTU-01 Manual de usuario
Revision: 2.0
User's Manual
May 18, 2000
Revision Number:2.0 SDSL Modem
i
SDTU-01/ET10
T
Ta
ab
bl
le
e
o
of
f
C
Co
on
nt
te
en
nt
ts
s
1. Overview.................................................................... 1
2. Features .................................................................... 1
3. Packaging.................................................................. 1
4. Appearance ............................................................... 2
5. Hardware Installation.................................................. 3
6. Management.............................................................. 4
7. Default values............................................................ 5
8. Software Upgrade ...................................................... 6
Appendix A. Console Setup................................................ 7
Appendix B. Command Line Interface................................. 8
Appendix C. Specifications............................................... 25
Hardware Specifications............................................... 25
Software Specifications................................................ 26
May 18, 2000
Revision Number: 2.0 SDSL Modem
ii
SDTU-01/ET10
T
Ta
ab
bl
le
e
o
of
f
F
Fi
ig
gu
ur
re
es
s
FIGURE 1: FRONT PANEL ...................................................................2
FIGURE 2: REAR PANEL.....................................................................2
FIGURE 3: HARDWARE INSTALLATIONS ................................................3
FIGURE 4: COMMAND TREE.................................................................9
May 18, 2000
Revision Number: 2.0 SDSL Modem
iii
SDTU-01/ET10
R
Re
ev
vi
is
si
io
on
n
M
Ma
ar
rk
ks
s
Revision Date Notes
V2.0 May 25, 2000 Software: 2.11B-H30.02-F45.108
May 18, 2000
Revision Number: 2.0 SDSL Modem
1
SDTU-01/ET10
1. Overview
The SDTU-01/ET10 is an SDSL modem supporting ATM bridging with
4-port 10Base-T Ethernet hub. The SDSL front end provides
symmetrical data rates from 144Kbps up to 2320Kbps in
programmable rate steps of 8Kbps. The SDTU-01/ET10 can be
configured to inter-operate with SDSL DSLAM or to support Point-to-
Point data transmission applications by flexible CO/RT configuration.
2. Features
üHigh Speed Symmetrical Data Transmission on Single Twisted Copper
Pair Wire
ü2B1Q Line Coding
üSymmetrical Multi-rate data transmission from 144Kbps up to
2320Kbps
üRFC 1483 Bridging over ATM over SDSL
ü4-port 10Base-T Ethernet hub for PC/LAN
üHigh quality, simple operation, low power consumption
üCompatible and interoperable with major Central Office side SDSL
DSLAM or Multi-service Access System
üLocal OAM&P through command line interface via RS-232 Craft
port
üLocal Telnet through the Ethernet interface
üRemote Telnet through SDSL interface
üSupports point-to-point applications
3. Packaging
This package consists of the following items:
4The SDTU-01/ET10 unit
4AC Adapter
4Installation and Operation Manual
49-pin to 9-pin serial configuration cable
May 18, 2000
Revision Number: 2.0 SDSL Modem
2
SDTU-01/ET10
4. Appearance
Front Panel
Figure 1: Front Panel
Rear Panel
Figure 2: Rear Panel
WAN Status: Blinks while training with DSLAM and On
when SDSL link is ready
Power: On when the power supply is properly connected.
Activity: Blinks while transmitting or receiving packets over one of Ethernet
ports
LINK Status:On when one of Ethernet ports is properly connected to a
LAN or PC
RJ11, SDSL inlet
RJ45*4, for connection to LAN or PC
Power Jack, for connection to an AC-DC power adapter, 12VDC, 1A
DB9, serial port for connection to ASCII data terminal
Alarm:Blinks while booting up, and On when there is
an error, continuous “On” indicates internal error
Green LED*4, On while corresponding Ethernet port is
connected. Blinks while transmitting or receiving
packets
Red LED, on when Ethernet
collision occur
May 18, 2000
Revision Number: 2.0 SDSL Modem
3
SDTU-01/ET10
5. Hardware Installation
1.Connect the SDSL cable, (item 1) indicated in Figure 3, to
the LINE port of RJ-11 socket.
2.Use a RJ-45 cable, (item 2) indicated in Figure 3, to connect
the SDTU-01/ET10 to the LAN or a PC with Ethernet adapter
installed.
Note: Be sure to use RJ-45 cross-over cable when
connecting to a hub.
3.Plug in the AC adapter to an AC power socket, then connect
the DC jack, (item 3) indicated in Figure 3, the DC inlet of the
SDTU-01/ET10.
4.Use a 9-pin RS-232 cable (item 4) indicated in Figure 3, to
connect the Console Port to a serial port of a terminal such
as PC with data terminal emulation software (Hyper Terminal)
installed, in order to perform local management.
Figure 3: Hardware Installations
(1)
(2)
(3)
(4)
SDSL outlet
Management Terminal
May 18, 2000
Revision Number: 2.0 SDSL Modem
4
SDTU-01/ET10
6. Management
SDTU-01/ET10 supports simple, flexible and easy-to-operate
methods for management purposes. The SDTU-01/ET10 can be
managed via the following paths, refer to Appendix B for
detailed information.
üConsole port – use the RS-232 cable for connecting SDTU-
01/ET10 to a console terminal or a PC running terminal
emulation program, such as Hyper Terminal, see Appendix A for
proper console setup.
üLocal Ethernet Port – connect the Ethernet port to your local
area network or to a PC directly, “Telnet” SDTU-01/ET10 from any
workstation on the LAN.
üSDSL port from remote site – while SDSL connection is in
service, you may remotely “Telnet” SDTU-01/ET10 from a
workstation networking to the CO equipment.
Note: As operating SDSL modem requires technical know-how and
experience, it is recommended that management of the SDTU-
01/ET10 be performed by qualified technical staff only.
May 18, 2000
Revision Number: 2.0 SDSL Modem
5
SDTU-01/ET10
7. Default values
SDTU-01/ET10 is pre-configured with the following parameters; the
user may also re-load the default parameters by selecting Default from
the main menu.
LAN and VC setting WAN and SDSL
Ethernet (local) IP: 192.168.2.1 Side selected: CPE (RT) side
Subnet mask: 255.255.255.0 Auto Rate: disable
Protocol: RFC1483, bridge Mode Rate select: 2320Kbps
VPI/VCI: 8/35 Sign/Magnitude Bit Sequence: reverse
Spanning tree: disable Data Bit Polarity: Normal
Packet control: IP and PPPoE Scrambling: enable
Idle-cell-sending: enable
May 18, 2000
Revision Number: 2.0 SDSL Modem
6
SDTU-01/ET10
8. Software Upgrade
You may easily upgrade the SDTU-01/ET10's embedded
software by obtaining the compressed upgrade kit, ZIP file, from
the service provider then following the steps:
üExtract the ZIP file
üConnect SDTU-01/ET10 via the local Ethernet port or remote
SDSL link, make sure the SDTU-01/ET10 Ethernet IP address is
set and your terminal is properly configured so you can
successfully “ping” SDTU-01/ET10.
üUnder a DOS prompt, execute the command line “xupgrade
<IP address of SDTU-01/ET10>”, for instance “xupgrade
192.168.2.1”.
üThis upgrade process may take as long as 60 seconds.
üThen reboot SDTU-01/ET10 with new software.
NOTE: Strictly maintain stable power to SDTU-01/ET10 while
upgrading software. If power fails during the upgrading
process, contents in the memory could be destroyed and
the system may hang. In such a case, you must call the
dealer or system integrator for repair.
Otros manuales para SDTU-01
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Módem de CTC Union
CTC Union
CTC Union VDTU01 Manual de usuario
CTC Union
CTC Union xDSL Series Manual de usuario
CTC Union
CTC Union SHDTU03 Manual de usuario
CTC Union
CTC Union SDTU-01 Manual de usuario
CTC Union
CTC Union SHDTU03b Manual de usuario
CTC Union
CTC Union VDTU2-104 Manual de usuario
CTC Union
CTC Union ATU-R140 Manual de usuario
CTC Union
CTC Union VDTU2-102 Manual de usuario
CTC Union
CTC Union MSDTU01-A/E1 Manual de usuario
CTC Union
CTC Union I-DSL64 Manual de usuario
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario