CSL CS203X-2 Manual de usuario
CS203X-2 EPC Class 1 Gen 2 RFID
Reader User’s Manual
Version 2.0
CSL: The One-Stop-Shop for RFID
Solutions
USER'S MANUAL, VERSION 4.0
2
1 Content
1. Content ………………………………………………………………..……….…………….. 2
2. FCC and IC Statement ………………………………………………….……..…………… 3
3. INTRODUCTION ON FEATURES
3.1 CS203X-2 RFID Fixed Reader ……………………………….….………………… 6
3.2 Product Package ………………………………………………..…..……………….. 7
3.2.1 Basic Package Content …………………………………….…….…..……………… 7
3.3 Product Specification ………………………………………………………………… 8
4. INTRODUCTION ON APPLICATION
4.1 Basic Hardware ……………………………………..……………...……………….10
4.2 Power Supply …………………………………….…………………………………. 13
4.3 Demo Software on PC ………………………….………………………………….. 14
4.4 GPIO Ports Signals ……………………………….………………………………… 17
APPENDIX A
Frequency Channel Table ………………………………………..……………..………… 18
APPENDIX B
Link Profiles of CS203X-2 RFID Reader ………………………….……….…..…………. 19
APPENDIX C
Antenna Ports Operation Description ……………………………………….…….……….20
USER'S MANUAL, VERSION 4.0
3
2 FCC and FCC Statement
FCC regulatory conformance：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority to
operate the equipment.
USER'S MANUAL, VERSION 4.0
4
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 30 cm
between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IC regulatory conformance
This device complies with CAN ICES-3 (B)/NMB-3(B).
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Cet appareil est conforme à la norme CAN ICES-3 (B)/NMB-3 (B).
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 30 cm
between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
USER'S MANUAL, VERSION 4.0
5
Cet équipement est conforme aux limites d’exposition aux rayonnements de la IC établies pour
unenvironnement non contrôé. Cet équipement doit être installé et fonctionner à au moins 30cm de
distance d’un radiateur ou de votre corps.
USER'S MANUAL, VERSION 4.0
6
3 Introduction on Features
3.1 CS203X-2 RFID Fixed Reader
The CS203X-2 RFID fixed reader is a reader designed to work with an any personal computer
via the ethernet connection, where the application on the PCs would control the CS203X-2
reader to perform RFID tag reading and GPIO port ON/OFF operation.
Below photo shows the typical connection during operation of CS203X-2 fixed reader
Note: DO NOT use any antenna not including in the shipment package or specify within the
product manual. Use only the PowerAdaptor Unit included in the package.
USER'S MANUAL, VERSION 4.0
7
3.2 Product Package
3.2.1 Basic Package Content
The reader package contains:
•A CS203X-2 fixed reader
•Power Adaptor Unit
•Ethernet Cable–1 piece
USER'S MANUAL, VERSION 4.0
8
3.3 Product Specification
Figure 3-1 CS203X-2 Fixed Reader
Features:
ISO 18000-6C and EPCglobal Class 1 Gen 2 UHF RFID protocol compliant including
dense reader mode
Ultra long read range –peak at more than 18 meters for Monza R6 Dogbone tag
Sophisticated data handling for efficient management of large streams of tag data.
Highly configurable buffering and tag filtering modes to eliminate the redundant tag data
so as to reduce LAN traffic and server loading
Robust performance in dense-reader environments
Excellent in transmit and receive mode –generates a different combination of unique
reader-to-tag command rate, tag-to-reader backscatter rate, modulation format, and
backscatter type
Configurable parameters offer maximum throughput and optimal performance
Supports all Gen 2 commands, including write, lock and kill
USER'S MANUAL, VERSION 4.0
9
Specifications:
Physical Characteristics:
Length: 26.5 cm; Width: 26.5 cm; Height: 12 cm;
Weight: 4180 grams
Environment:
Operating Temp: -200C to 500C
Storage Temp: -400C to 850C
Humidity: 5% to 95% non-condensing
Antenna:
External antenna has a RP-SMA male connector
RF Power:
Internal conducted power 30 dBm
EIRPPower:
35 dBm (max.)
RFID Frequency Ranges:
902 -928 MHz band
Connectivity
Ethernet , Debug Serial(RS232)
Accessories:
Ethernet cable
GPIO cable
Order Code:
CS203X-2
Restrictions on Use:
Approvals, features and parameters may vary
depending on country legislation and may change
without notice
USER'S MANUAL, VERSION 4.0
10
4 Introduction on Application
4.1 Basic Hardware
The CSL CS203X-2 RFID Reader is an EPCglobal Class 1 Gen 2 handheld reader product.
Below is the front view of the CS203X-2 reader. There are LEDs at side to indicate the
operating status
1) Power On
2) RFID Read
3) Active antenna port being selected (default internal)
Figure 4-1 CS203X-2 Reader Front-side View
Tabla de contenidos
Otros manuales de Sistema RFID de CSL
