Crow OLED Manual de usuario

ELECTRONIC ENGINEERING LTD.

OLED Keypad

User’s Guide

December 2009

Crow Limited Warranty

(Crow) warrants this product to be free from defects in materials and workmanship under normal use and service

for a period of one year from the last day of the week and year whose numbers are printed on the printed circuit

board inside his product.

Crow’s obligation is limited to repairing or replacing this product, at its option, free of charge for materials or labor,

if it is proved to be defective in materials or workmanship under normal use and service. Crow shall have no

obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by

anyone other then Crow.

There are no warranties, expressed or implied, of merchantability or fitness for a particular purpose or otherwise,

which extend beyond the description on the face hereof. In no case shall Crow be liable to anyone for any

consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any

other basis of liability whatsoever, even if the loss or damage is caused by Crow’s own negligence or fault.

Crow does not represent that this product can not be compromised or circumvented; that this product will prevent

any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that this product will in all

cases provide adequate warning or protection. Purchaser understands that a properly installed and maintained

product can only reduce the risk of burglary, robbery or other events occurring without providing an alarm, but it is

not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or

damage as a result. Consequently, Crow shall have no liability for any personal injury, property damage or any

other loss based on claim that this product failed to give any warning. However, if Crow is held liable, whether

directly or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause

or origin, Crow’s maximum liability shall not in any case exceed the purchase price of this product, which shall be

the complete and exclusive remedy against Crow.

Information in this document is subject to change without notice. No part of this document may be reproduced or

transmitted in any form or by any means, electronic or mechanical, without express written permission of

Print version 001

Contents

KEYPAD DESCRIPTION ........................................................................................................................3

FUNCTION KEYS................................................................................................................................. 3

ALPHANUMERIC KEYS .......................................................................................................................... 4

AUDIBLE SIGNALS .............................................................................................................................. 4

INDICATORS ..................................................................................................................................... 4

SUMMARY OF FUNCTIONS ..................................................................................................................... 4

OPERATING THE KEYPAD ....................................................................................................................7

HOW TO ARM THE SYSTEM BEFORE EXIT ................................................................................................... 7

Preparing the System for Arming.......................................................................................................7

Arming the System............................................................................................................................7

Quick Arm (When enabled at installation)..........................................................................................7

Disarming the System .......................................................................................................................8

Stopping and Resetting Alarms..........................................................................................................8

ARMING THE SYSTEM WHILE STAYING HOME.............................................................................................. 9

Arming the System in Stay Mode.......................................................................................................9

Disarming the System .......................................................................................................................9

HOW TO BYPASS ZONES ..................................................................................................................... 10

USING CHIME (IF ENABLED AT INSTALLATION) .......................................................................................... 11

EMERGENCY ALERTS.......................................................................................................................... 12

How to initiate Panic........................................................................................................................12

How to initiate Medical Alarm...........................................................................................................12

How to initiate Fire Alarm.................................................................................................................12

GENERATE THREAT OR DURESS ............................................................................................................ 12

SYSTEM MESSAGES ........................................................................................................................... 12

HOW TO READ TROUBLE MESSAGES AND EVENTS FROM MEMORY.................................................................... 12

SPECIAL INDICATIONS........................................................................................................................ 13

HOW TO CONTROL OUTPUTS AND DEVICES .............................................................................................. 14

ENTERING THE USER PROGRAM/CLIENT MODE .......................................................................................... 14

HOW TO CHANGE OR ADD CODES ......................................................................................................... 14

About Master Code and the User Code ...........................................................................................14

How to Change the Master Code.....................................................................................................15

How to Add or Change the User Code.............................................................................................15

How to Delete the User Code..........................................................................................................15

ADDING/CHANGING TELEPHONE NUMBERS............................................................................................... 15

HOW TO SET TIME AND DATE .............................................................................................................. 16

HOW TO START WALK TEST MODE ........................................................................................................ 16

HOW TO ANSWER AN IN-COMING CALL................................................................................................... 16

USING THE REMOTE COMMAND CONTROL ................................................................................................ 16

USING LOCAL COMMAND CONTROL........................................................................................................ 17

LCD KEYPAD IN LOCAL EDIT MODE ....................................................................................................... 18

Accessing Local Edit Mode..............................................................................................................18

Edit Names at Local Edit Mode........................................................................................................19

Button Assignment..........................................................................................................................20

Changing Language........................................................................................................................21

Adjusting Backlighting .....................................................................................................................21

Resetting All Text to Default ............................................................................................................22

Contents

Copying Text to another LCD or OLED Keypad...............................................................................23

Exiting Local Edit Program Mode.....................................................................................................23

Keypad Description

The OLED Keypad shows all the information required to operate the system. The User

communicates with the alarm system via the keypad. The Keypad displays continuous

information about the status of the alarm system, and enables the User to operate the system in

different modes, change settings and program Users access codes.

The keypad also collects and records events to be displayed afterward on request, to overview

system activities, and to analyze system performance for diagnostics.

Function Keys

These keys are used to arm the system, enter commands to alter system settings, or scroll

through the history events.

ARM, STAY, BYPASS, PROGRAM, CONTROL, MEMORY, PANIC, ENTER, MENU,

, , , - these buttons are pre-programmed:

- Arm Area A

- Arm Area B

- Chime

- Bypass

These buttons can be reprogrammed at Local Edit mode (see P21 "button assignment

ARM

STAY

ARM/READY LED

TROUBLE LED

OPEN

ZONES

STATUS

HELP

Keypad Description

Alphanumeric Keys

These keys are used to enter codes, Initiate Emergency or used for programming.

Audible Signals

When the keypad is used to activate or deactivate the different functions it emits different

audible beeps. Their meaning is described in the table below.

Table 1 List of Audible Signals

Sound Sequence Description

Short beep Once only A key in the keypad has been pressed.

3 short beeps Once only Operation carried out successfully.

Long beep Once only Illegal operation or wrong key pressed.

Slow beeping Through the Exit or

Entry delay time

Exit or entry delay warning. When arming the system, this

indicates you must exit the protected area. When disarming the

system, it indicates you have entered the protected entry zone.

Indicators

qARM/READY -RED/GREEN

qTROUBLE-RED

Summary of Functions

The system's main functions are listed in table

Function Keys Description Notes

Full or

Partition Arm C

C O D E

Initiates full arm

Full Arm C

Initiates full arm Only if enabled by

installer. Another way use

Arm operation is to enter

a MENU and scroll

down, until the Arm

option.

Disarm

during exit C

Disarms the system

during exit delay

Only when slow beeping

is emitted.

Disarm C

C O D E

Disarms the system Stopping Alarms.

Function Keys Description Notes

Arm Stay C

C O D E

Initiates partial alarm

when the user is home

Only if enabled by

installer.

Arm Stay CInitiates partial alarm

when the user is home

Another way use Stay

operation is to enter a

MENU and scroll

down, until the Stay

option.

Keypad Description

Function Keys Description Notes

Disarm Stay C

C O D E

Disarms the system

Disarm Stay CDisarms the system

Bypass C

BYPASS

Zone #

Bypasses a zone(s) Repeat the procedure to

un-bypass zones. Bypass

button can be one of the

following buttons:

, , ,

Another option to bypass

is by enter MENU and

scroll down until the

bypass option.

Option 1:

At this case

Button assigned to

operate bypass.

(default)

Option 2:

MENU:

Initiate Panic C+

Activates emergency

alert

Initiate

Medical C+

Activates emergency

alert

Initiate Fire

Alarm C+

Activates emergency

alert

Memory C

MEMORY

Initiates display of

events from memory.

or cancels

memory readout

Displays events and

current faults of the

system.

Memory button can be

one of the following

buttons: , , ,

Another option to enter

memory is by enter MENU

Keypad Description

Function Keys Description Notes

and scroll down until

the Memory View option.

Chime

Enable/disabl

Enable or disable chime

function

Chime button can be one

of the following buttons:

, , , .

(default)

Another way to use

Chime operation is to

enter a MENU and

scroll down, until the

Chime option.

Control C

CONTROL

Device#

Activates or deactivates

outputs and devices

Control button can be one

of the following buttons:

, , , .

Note: If you started an operation incorrectly, press to exit and return to the previous mode.

Operating the Keypad

How to Arm the System before Exit

Preparing the System for Arming

Verify that all zone indicators are off, when all zones are closed (all doors, exits and windows are

closed and motion in the protected area is restricted or bypassed), the system is ready to be

armed. If one or more zone indicators are illuminated, it displays the open zones.

When system is ready, there is ready indication light at green.

Close open zones, or bypass them. Bypass any zone you cannot close. To see which zones

are in bypass mode, press or

Note: Bypassed zones are not protected.

Arming the System

Before leaving premises you must arm the system.

Arming the alarm system turns on all detectors in the partition/s being armed.

1. Enter your code.

2. Press to arm the system.

There is an exit delay prior to the system being armed. During this delay time, a slow

beeping is heard to indicate that the system is not armed yet and reminds you to vacate

the protected area.

The following writing lights up at the screen to indicate that the system is armed:

Armed A –for Area A, and Armed B –for Area B.

The indicators may go out few seconds after exit delay times out, depending on the installation

setting.

qTo disarm the system during the exit delay, press .

Quick Arm (When enabled at installation)

qPress to arm the system.

During exit delay time, a slow beeping is heard reminding you to vacate the protected area.

Operating the Keypad

Disarming the System

1. Enter your code.

2. Press .

The Aor Bindicator goes off, the system is now disarmed.

Stopping and Resetting Alarms

1. Enter your code.

2. Press .

This stops the alarm at any time, and also turns off any audible sirens.

Tabla de contenidos

Otros manuales de Teclado de Crow

Crow

Crow OLED Keypad Manual de usuario

Crow

Crow Runner Series Instrucciones de funcionamiento

Crow

Crow Power Wave CR16M Instrucciones de funcionamiento

Crow

Crow Runner Series Manual de usuario

Crow

Crow Power Wave CR16M Manual del propietario

Crow

Crow FW-KP Manual

Manuales populares de Teclado de otras marcas

BFT

BFT SELETTO Manual de usuario

Micro Id

Micro Id MP7G3BL Manual de instrucciones

WindowMaster

WindowMaster WLI 130 Manual de usuario

ACT

ACT ACT PRO 1030 Manual de usuario

Cardin

Cardin SSB Series Manual de usuario

Harman Kardon

Harman Kardon KP 1 Manual de usuario

Chamberlain

Chamberlain KPR2000 Guía del usuario

CYP

CYP CR-KP1 Manual de usuario

Aeware

Aeware k-35 Series Guía de referencia

Aritech

Aritech CS-175 Series Manual de usuario

GE NetworX NX-1600E Series Manual de usuario

Lenze AC Tech

Lenze AC Tech MC SERIES Manual de usuario

Burg Wächter

Burg Wächter secuENTRY 7711 Manual de usuario

Aeware

Aeware in.k450 Manual de usuario

Lenze

Lenze EPM-H410 Manual de usuario

Toshiba

Toshiba RKP007Z Manual de usuario

Gemini

Gemini GEM-DXK1 KEYPAD Manual de usuario

Russound

Russound MDK-C5 Manual de funcionamiento