CrimeStopper RS-800.III Manual de usuario

RS800 Series III

Remote Engine Starting System

OPERATING INSTRUCTIONS

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from

the use of this equipment. This system is designed to be professionally installed onto a vehicle in which all items, such

as parking brake and all associated components, door switches, transmission shift linkage, throttle linkage, and all

engine safety features, are in perfect working condition.

DO NOT install this Remote Engine Starting System on MANUAL TRANSMISSION vehicles. If accidentally left in

gear the vehicle could become a self-propelled threat to life and property.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system and its

safety features. B) Check for proper operation of these safety features prior to accepting delivery of the vehicle from the

installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper operation of

this system and its safety features. D) Always leave the doors and windows closed and locked to protect against

accident and theft.

DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is adequate

ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.

This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1)

This device may not cause interference, and (2) this device must accept any interference that may be

received, including interference that may cause undesired operation. The manufacturer is not

responsible for any radio or TV interference caused by unauthorized modification to this equipment.

Such modification could void the user's authority to operate the equipment.

REV. A 09/2002

OPERATION

REMOTE ENGINE STARTING - SUCCESSFUL START:

TRANSMITTER BUTTONS

START

LOCK/

REMOTE

START

UNLOCK

CAR 1-2

1. Press and release the remote start button.

2. Parking lights flash once, then turn ON along with the IGN/ACC

circuits

3. After a few seconds the Starter Motor engages. (Parking lights

and Acc circuits turn off while cranking.)

4. Engine Starts and Runs. Parking Lights and Acc turn back on,

Doors Lock.

5. Engine will remain running for programmed run time or until reset

with Brake pedal.

REMOTE ENGINE STARTING - UNSUCCESSFUL START

In the event that the engine does not start on the first attempt, the

system shuts down for a few seconds, then attempts to restart the

engine a 2nd and 3rd time. For hard starting engines, the unit will

allow a starter crank time of up to a maximum of10 seconds. This should provide ample cranking time for difficult starts,

but is limited to help prevent damage to the starter from over cranking in the case of a malfunctioning unit.

1. If engine starts on 2nd or 3rd attempt, see steps 4 & 5 above of "Successful Start".

2. If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER ATTEMPTS

WILL BE MADE AUTOMATICALLY

TURNING OFF A REMOTE STARTED ENGINE:

1. Engine is running in Remote Start (Parking lights are ON).

2. Press and release the Remote Start button again.

3. Engine turns & parking lights OFF, Doors remain locked or will re-lock/re-arm if applicable.

KEYLESS ENTRY (POWER DOOR LOCK CONTROL) (OPTIONAL)

This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) through the

transmitter for safety and convenience. This feature may require extra labor and/or parts to install. Press the

Lock/Unlock button on the transmitter as you leave or come near the vehicle. Parking lights will flash 1X for lock and

2X’s for unlock.

NOTES: Doors lock automatically when vehicle is Remote Started. Starter Disable/Anti-grind is also enabled/disabled

with the lock/unlock button. If an anti-grind/starter kill relay is installed on a vehicle without power door locks, the

lock/unlock button of the remote control must still be used to operate the Starter disable. We recommend installing the

LED also when installing the Optional Starter Disable, as this will be your only indicator that it is active.

OPERATION

ANTI-GRIND / STARTER DISABLE (OPTIONAL)

Prevents the driver from accidentally grinding the starter if the Ignition key is turned too far (to the start position) while

engine is already running from the remote starter. Starter circuit is automatically disabled when doors are locked using

the remote control to act as an added security feature.

VALET MODE / STARTER DISABLE OVERRIDE

Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The

remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position,

press and hold Program/Valet switch for 6 seconds. The LED will turn on solid and the system is now in valet. Perform

this procedure again to exit of Valet mode. The keyless entry will still function normally while in valet mode. In the event

of a lost or broken transmitter, perform this step to override the Optional Starter Disable (If installed).

HOOD OPEN SAFETY SWITCH (WITH INSTALLED HOOD PIN SWITCH)

Prevents the engine being Remote Started when hood is open and will abort a remote start if running. Eliminates risk of

injury to someone working under the hood of the vehicle. This unit will not attempt a start if a hood pin is installed.

BRAKE PEDAL RESET CIRCUITRY

Prevents starting or shuts off a remote started vehicle when this circuit is active or activated. Prevents unauthorized

tampering. This circuit shuts the system down immediately when brake pedal is pressed if key is not in ignition and

turned to the run position.

NOTE:

In the event of a major malfunction, performing electrical service or jumpstarting the vehicle you should remove the main

Power Fuse(s) to protect the unit from possible damage.

TRANSMITTER PROGRAMMING

Note: All transmitter codes must be learned at time of programming!! The RS800 allows storage of up to 4

different transmitter codes.

1. Open Hood (Ground Gray hood pin wire if no hood pin is installed).

2. Turn key to the ON position.

3. Press Programming button 4 times. After a few seconds, the unit will flash the parking lights 4 times.

4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a 2nd

code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd code and

4 flashes for the 4th code. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise

turn key off and close hood.

2-VEHICLE OPERATION

The RS-800 III system can be used for 2 car operation. A single RS800 III remote can control two independent vehicles

with RS800 III systems installed.

SETUP:

See diagram below on how to switch your remote to car 2 operation. Once you have switched your remote to Car 2,

then follow the transmitter programming steps AT VEHICLE #2 and learn YOUR remote, along with Car 2’s existing

remotes. Transmitter programming steps are listed on previous page.

CAR

Slide

RS 800

III

CAR

I /

CAR

OPERATION

START

Crimestopper Security Products Inc.

1770 S. Tapo St. Simi Valley, CA 93063

(800) 998-6880 www.crimestopper.com

Otros manuales para RS-800.III

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arranque remoto de CrimeStopper

CrimeStopper

CrimeStopper RS-999.FM Manual de usuario

CrimeStopper

CrimeStopper EZEE Start EZ-1 Manual de usuario

CrimeStopper

CrimeStopper PS01-G5 Manual de usuario

CrimeStopper

CrimeStopper Cool Start RS-850 Manual de usuario

CrimeStopper

CrimeStopper RS-800.IV Manual de usuario

CrimeStopper

CrimeStopper Ezee Start EZ-90 Manual de usuario

CrimeStopper

CrimeStopper SP-400 Manual de usuario

CrimeStopper

CrimeStopper REVO-1 Series Manual de usuario

CrimeStopper

CrimeStopper SP-400 Manual del sistema

CrimeStopper

CrimeStopper CS-830RKE Manual de usuario

CrimeStopper

CrimeStopper RS800ER Manual de usuario

CrimeStopper

CrimeStopper Ezee Start EZ-777 FM Manual de usuario

CrimeStopper

CrimeStopper COOL START RS-901 Manual de usuario

CrimeStopper

CrimeStopper Ezee Start EZ-30DP Manual de usuario

CrimeStopper

CrimeStopper Pro Start LCPRO-3 Manual de usuario

CrimeStopper

CrimeStopper Cool Start RS-7 Manual de usuario

CrimeStopper

CrimeStopper ezee Start EZ-777 VII Manual de usuario

CrimeStopper

CrimeStopper EZEE START EZ-10 Manual de usuario

CrimeStopper

CrimeStopper EZEE Start EZ-45DP Manual de usuario

CrimeStopper

CrimeStopper REVO-1 Series Manual de usuario

CrimeStopper

CrimeStopper RS1-G4 Cool Start Manual de usuario

CrimeStopper

CrimeStopper Ezee Start EZ-30DP Manual de usuario

CrimeStopper

CrimeStopper CoolStart RS900ER Manual de usuario

CrimeStopper

CrimeStopper Infinity CS-2900DP-FM Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual