Crestron ZUMMESH-JBOX Series Manual de usuario

The Crestron® ZUMMESH-JBOX load controller provides sophisticated

lighting control with simple installation. The ZUMMESH-JBOX mounts

directly to a 4 in. square junction box and pairs wirelessly with one or more

Zūm wireless keypads.

The following ZUMMESH-JBOX Devices are available:

lZUMMESH-JBOX-5A-LV: 0-10 V Dimmer, 5 A, 100-277 V

lZUMMESH-JBOX-16A-LV: 0-10 V Dimmer, 16 A, 100-277 V

lZUMMESH-JBOX-16A-LV-EM: 0-10 V Dimmer, 16 A, 100-277 V,

Emergency Load Controller

lZUMMESH-JBOX-20A-SW: High Inrush Switch, 20 A, 100-277 V

lZUMMESH-JBOX-20A-PLUG: Plug Load Switch, 20 A, 100-240 V

lZUMMESH-JBOX-PSU: Power Supply

In the Box

1 ZUMMESH-JBOX, Zūm™ Mesh Wireless J-Box Load

Controller

Additional Items

1 Yellow Wire Nut, 22-10 AWG (2049245)

1 Locknut (2047626)

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Installation

WARNING: To avoid fire, shock, or death, turn off the power at the

circuit breaker or remove the fuse and test that the power is off

before wiring!

NOTES:

lInstall and use this product in accordance with appropriate

electrical codes and regulations.

lA licensed electrician should install this product.

lThe product should project 3-11/16 in. (93 mm) from the junction

box when installed.

lFor a Chicago plenum compliant installation, refer to the

ZUMMESH-JBOX-FMKT-CP Quick Start (8461) at

www.crestron.com/manuals.

To install a ZUMMESH-JBOX:

1. Turn the power off at the circuit breaker.

NOTE: When installing a ZUMMESH-JBOX-16A-LV-EM, ensure

that any backup power source is also off.

2. Mount the ZUMMESH-JBOX to the J-Box using the included locknut.

3. Wire the ZUMMESH-JBOX as shown in the following diagrams.

ZUMMESH-JBOX-5A-LV, ZUMMESH-JBOX-16A-LV, and

ZUMMESH-JBOX-20A-SWWiring

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

ZUMMESH-JBOX-20A-PLUG Wiring

ZUMMESH-JBOX-PSU Wiring

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

ZUMMESH-JBOX-16A-LV-EM Wiring IMPORTANT SAFEGUARDS:

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

lDo not mount near gas or electric heaters.

lEquipment should be mounted in locations and at heights where it

will not be subjected to tampering by unauthorized personnel.

lThe use of accessory equipment not recommended by the

manufacturer may cause an unsafe condition.

lDo not use this equipment for other than its intended use.

SAVE THESE INSTRUCTIONS

WARNING: The installation and the use of this product within a

specific installation must be approved by an applicable local, state, or

federal Authority Having Jurisdiction (AHJ). All installations must be

performed by qualified personnel according to applicable local and

regional codes and standards. Requirements vary between

jurisdictions.

NOTES:

lWhen wiring a ZUMMESH-JBOX-16A-LV-EM, ensure that power is

routed through a transfer switch for emergency load control.

lAfter normal power is lost, 200ms (120V) or 750ms (277V) must

pass before the ZUMMESH-JBOX-16A-LV-EM is powered by an

emergency power source.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Emergency Lighting

The ZUMMESH-JBOX-16A-LV-EM provides emergency load control to

meet UL® 924 standards. Refer to Installation to install the device.

The device operates as a standard J-box load controller in normal

conditions, where it can bind to keypads, make scene modifications, follow

sensor control states, and perform any other actions that

ZUMMESH-JBOX controllers can. When power to the lighting system is

lost, the device enters Emergency Mode.

In Emergency mode, the device operates with the following behavior:

lAll loads in the zone fully illuminate.

lAttached loads remain fully illuminated for 90 minutes or until normal

power is restored to a non-emergency AC-powered device, whichever

comes first.

lKeypads and any other user controls are disabled.

lDaylight sensors, occupancy sensors, and vacancy sensors are

disabled.

lThe TEST button toggles the connected load On and Off.

The device will exit Emergency mode and return to normal operation when

normal power is restored. Communications with nonemergency devices

continue when normal power is restored.

Test the Loads

To verify system wiring, the loads can be tested before setting up the Zūm

space. Press the TEST button to toggle the connected loads on and off.

Press and hold the TEST button to cycle the connected dimmers.

Creating and Modifying Zūm Spaces

How to Set Up a Zūm Space and Add Zūm Devices

Once all devices are physically installed in a board room or conference

space, a new Zūm space can be created and devices added.

NOTES:

lSet up only one Zūm space at a time.

lFor simplified setup of a Zūm space, use the Zūm app on a mobile

device.

Create a New Zūm Space

Creating a Zūm space defines the area where the devices are located,

such as a board room or conference room. A Zūm space is created with a

keypad, dimmer or switch, a J-box device, or an AV Bridge.

NOTES:

lOnly one device in a space can create a Zūm space.

lA Zūm space cannot be created from a battery-powered keypad.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Using a J-Box Device or AV Bridge

To create a new Zūm space using a J-box device or an AV Bridge:

1. Press the SETUP button 5 times.

2. Press and hold the SETUP button until the LED on the device lights

(about 10 seconds). After approximately 3 seconds, the device LED

begins flashing slowly. This indicates that the Zūm space is now

created and in Joining mode, allowing you to add devices.

NOTE: The device used to create the Zūm space is automatically added

to the space and does not need to be added in Step 2.

Using a Keypad, Dimmer, or Switch

To create a new Zūm space using a keypad, dimmer, or switch:

1. Press the bottom button 5 times.

2. Press and hold the bottom button until the LED on the device lights

(about 10 seconds). After approximately 3 seconds, the device LED

begins flashing slowly. This indicates that the Zūm space is now

created and in Joining mode, allowing you to add devices.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Add Zūm Devices to the Zūm Space

After a new Zūm space is created, add Zūm devices while the space is in

Joining mode.

NOTES:

lTo conserve battery power, battery-powered devices do not flash

their LEDs after joining the space. AC-powered devices in the space

will flash their LED to indicate that the space is in Joining mode.

lA Zūm mesh device can belong to only one space.

lJoining mode ends automatically after 4 minutes.

Adding a ZUMMESH-JBOX or AV Bridge

To add the ZUMMESH-JBOX or AV Bridge to a Zūm Space:

1. Press the SETUP button 3 times.

2. Press and hold the SETUP button until the LED on the device lights (up

to 10 seconds). The LED on the device will start to flash slowly to

indicate that it has joined the space.

NOTE: Only one ZUMMESH-AVBRIDGE can be installed per Zūm

space.

Adding a Keypad, Dimmer, or Switch

To add a keypad, dimmer, or switch to a Zūm space:

1. Press the top button 3 times.

2. Press and hold the button until the LED on the device lights (up to 10

seconds). The LED on the device will start to flash slowly to indicate

that it has joined the space.

Adding a Photocell or Occupancy/Vacancy Sensor

To add a photocell or occupancy/vacancy sensor to a Zūm space:

1. Press the SETUP button 3 times.

2. Press and hold the button until the LED on the device lights (up to

10seconds) to indicate that it has joined the space.

Complete Zūm Space Setup

To finish creating a Zūm space, press any button on an AC-powered

device that is part of the Zūm space to exit Joining mode.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Add a Zūm Device to an Existing Zūm Space

Add new Zūm devices to an existing Zūm space by placing the Zūm space

in Joining mode.

Add the Zūm Device using a J-box device:

1. Enter Joining mode.

a. Press the SETUP button 2 times.

b. Press the TEST button once. The LEDs on all devices in the space

(except battery-powered devices) flash slowly to indicate that the

devices are part of the space and that the space is in Joining mode.

2. Add the Zūm Device according to Add Zūm Devices to the Zūm Space.

3. Press any button on a device that is part of the Zūm space to exit

Joining mode.

Using a Keypad, Dimmer, or Switch

Add the Zūm device using a keypad, dimmer, or switch:

1. Enter Joining mode.

a. Press and hold both the top and bottom buttons until the LED

lights (about 5 seconds).

b. Press the top button once.

c. Press the bottom button once. The LEDs on all devices in the space

(except battery-powered devices) flash slowly to indicate that the

devices are part of the space and that the space is in Joining mode.

2. Add the device according to Add Zūm Devices to the Zūm Space.

a. Press the SETUP button 3 times.

b. Press and hold the SETUP button until the LED on the

ZUMMESH-JBOX lights (up to 10 seconds). The LED on the

ZUMMESH-5A will start to flash slowly to indicate that it has joined

the space.

3. Press any button on a device that is part of the Zūm space to exit

Joining mode.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Attach a J-Box Module

A J-box module, such as the ZUMMESH-NETBRIDGE or ZUMMESH-CCO

(both not included), can be attached to any J-box device.

NOTE: For product specifications and additional installation details,

refer to the ZUMMESH-NETBRIDGE Quick Start (Doc. 7955) or

ZUMMESH-CCO Installation Guide (Doc. 7935) at

www.crestron.com/manuals for details.

Attach the J-box module to the ZUMMESH-JBOX device.

1. Use a flat-head screwdriver to remove the cover on the

ZUMMESH-JBOX device. Insert the flat-head screwdriver into the slot

next to the cover and pry upward to remove the cover.

2. Align the ports on the J-box module and the ZUMMESH-JBOX device,

and then insert the J-box module into the ZUMMESH-JBOX device.

The J-box module snaps into place.

If the J-box module needs to be removed, place your thumb on the side of

the J-box module that is closest to the J-box and gently push the module

away from the J-box. The module should easily separate from the J-box

device.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Connect the Network Bridge to the

Zūm Net Wireless Gateway

The Zūm Network Bridge connects wirelessly to the Zūm Net Wireless

Gateway to form a centrally managed, enterprise-wide lighting control

system.

Add the Zūm Network Bridge to the Zūm Net Wireless Gateway’s

network:

1. Press the ACQUIRE button on the Zūm Net Wireless Gateway to place

the gateway into Acquire mode.

2. Join the Zūm Net Wireless Gateway’s network.

a. Press the SET button on the Network Bridge 3 times.

b. Press and hold the SET button until the LED flashes once (up to 10

seconds). The LED on the Network Bridge flashes slowly to indicate

that it is searching for a network to join.

lThe LED lights for 5 seconds when the network bridge

successfully joins the gateway.

lThe LED flashes quickly to indicate that the network bridge

failed to join the gateway. Press the SET button to acknowledge

the failure and then repeat this procedure.

3. Press the ACQUIRE button on the gateway to exit Acquire mode.

Calibrate and Test the Daylight

Sensor

To enable daylight harvesting, calibrate and then test the daylight sensor

after all devices are installed and powered in the Zūm space.

NOTES:

lOnly dimmers are capable of adjusting load levels that are driven by

daylight sensor readings.

lDaylighting only operates when Scene 1 is enabled.

lCalibrate the daylight sensor during the day when the sun is bright.

Avoid light fluctuations caused by clouds that are rapidly exposing

and hiding the sun.

lDo not stand between the daylight sensor and the windows. Doing

so affects the readings and can result in poor calibration settings.

ZUMMESH-JBOX Series QuickStart

Zūm™ Mesh Wireless J-Box Load Controllers

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Crestron

Crestron

Crestron SP-SC Manual de usuario

Crestron

Crestron DigitalMedia DM-RMC-100-1 Cómo utilizar

Crestron

Crestron TSW-1050-FMKT Manual de usuario

Crestron

Crestron SP-RY Manual de usuario

Crestron

Crestron C2N-SSC-2 Cómo utilizar

Crestron

Crestron PC-200 Manual del propietario

Crestron

Crestron MC2W Manual

Crestron

Crestron 3 Series Manual de usuario

Crestron

Crestron DigitalMedia 8G DM-RMC-200-S Dibujo dimensional

Crestron

Crestron CNECI-4A Manual de usuario

Crestron

Crestron 4 Series Manual de usuario

Crestron

Crestron DigitalMedia 8G+ DM-RMC-200-C Dibujo dimensional

Crestron

Crestron ST-VC Manual de usuario

Crestron

Crestron 4K DigitalMedia 3-Series Dibujo dimensional

Crestron

Crestron HD-CTL-101 Manual de usuario

Crestron

Crestron CP3-R Manual de usuario

Crestron

Crestron CLCI-MCEX Manual de usuario

Crestron

Crestron QM-RMC Manual de usuario

Crestron

Crestron MPC-M10 Cómo utilizar

Crestron

Crestron MC2W Manual de usuario

Crestron

Crestron CEN-TVAV Manual de usuario

Crestron

Crestron 302 Manual de usuario

Crestron

Crestron IPAC Manual de usuario

Crestron

Crestron MPC-M10 Dibujo dimensional

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario