Cornelius Nordic CCM1030 Manual de usuario
ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
© 2007-2010, IMI Cornelius Inc. - 1 - Publication Number: 620204732INS
INSTALLATION INSTRUCTIONS
ED/DF300 30” CCM330/430/530/630/830/1030 NORDIC BLACK/GRAY
STYLE LID KITS
This Nordic style kit applies to the Cornelius 30” wide CCM330/430/530/630/830/1030 ice maker.
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer’s instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
The dispenser must be secured with 3/8-16 bolts (6) to the counter before installing this Ice Maker Adapter Kit. Refer
to the installation manual and Figure 3 for the counter mounting template.
NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 sec-
onds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper
front panel.
1. Unpack the kit.
2. Remove the two (2) screws from each side of the dispenser cabinet and the plastic hopper covers (2) that were
shipped with the unit.
3. Place the adapter lid on the unit and use the four (4) screws that were removed to fasten the lid in place.
4. Install the ice baffle on the lid assembly as shown in Figure 2.
Table 1. Supplied Loose Parts
Item No. Part No. Name Qty.
1 15209 Adapter Lid 1
222127 Bracket 2
350904 RTV 1
452946
52964
Cover, Gray
Cover, Black 1
591957 Label 1
6620042919 Baffle, Ice 1
770226 #10 x 3/4” Sheetmetal Screw 12
8620701902 Acorn Nut, 8--32 Nylon 4
9620701901 Sealing Washer 4
10 611701903 #8 Nylon Washer 4
11 15192 Lid Opening Cover (For 22–inch Wide Icemakers) 2
12 630500109 Bin Stat 1
Release Date: November 4, 2010 www.cornelius.com Revision: B
ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
Publication Number: 620204732INS - 2 - © 2007-2010, IMI Cornelius Inc.
IMPORTANT: The baffle prevents ice from over–filling the manual fill area during agitation/
dispensing with a full storage bin and forcing the manual fill cover off.
5. Seal the ice maker to the top of the dispenser after determining the correct location for the ice maker (see Figure 1).
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so
that the ice maker will set on the RTV.
B. Set the ice maker onto the lid and position it as required.
C. Wipe away the excess RTV.
6. Drill 0.136” diameter holes into the ice maker cabinet and the dispenser lid using the ice maker mounting brack-
ets as templates. USE CAUTION SO AS NOT TO DRILL INTO ANY ICE MAKER COMPONENTS (CON-
DENSER, TUBING, ETC.). Secure the brackets using the #10 sheet metal screws provided.
7. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in the bottom of
the ice maker. Wrap the eye of the wire form over the stud near the hole to the end of the wire form bracket and
wrap the tube around the end of the bracket several times, insuring the tube is secure.
NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from the ice-
maker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.
8. For 22–inch wide ice makers, locate the lid opening covers (2) (item 11) as shown in Figure 1. Secure the covers
to the adapter lid by drilling 0.136” diameter holes into the lid. Use the covers as templates to locate the mounting
holes. Secure the covers with the # 10 sheet metal screws.
9. Locate the cleaning caution label (item 5) on the manual ice fill cover (item 4) as shown in Figure 1. Place the
manual fill cover in position over the flange on the lid assembly and the front access hopper opening.
10. The unit is now ready for operation.
Figure 1. ED/DF300 Kit
ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
© 2007-2010, IMI Cornelius Inc. - 3 - Publication Number: 620204732INS
Figure 2. ED/DF300 Kit Ice Baffle Installation
Figure 3 ED/DF300 Mounting Template
ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
Publication Number: 620204732INS - 4 - © 2007-2010, IMI Cornelius Inc.
Figure 4. Bin Stat
Figure 5. Detail X
FRONT PANEL OF ICE MAKER
REMOVED FOR CLARITY
SEE DETAIL X
IN FIGURE 3
DETAIL X
SCALE 0.580
NOTE: BINSTAT MUST BE WRAPPED AROUND SUPPORT AS SHOWN.
BINSTAT COIL
SUPPORT
NOT SUPPLIED
WITH BINSTAT
Este manual sirve para los siguientes modelos
10
Tabla de contenidos
Otros manuales de Máquina de hielo de Cornelius
Cornelius
Cornelius ED150 "K" Style Lid Kit Manual de usuario
Cornelius
Cornelius IDC215 Manual de usuario
Cornelius
Cornelius Nordic CCU0300 Series Manual de usuario
Cornelius
Cornelius pmnice systems Manual de usuario
Cornelius
Cornelius Ice Cube Maker JEACS50SL1 Manual de usuario
Cornelius
Cornelius P/N 620046011 Manual de usuario
Cornelius
Cornelius D100 Manual de usuario
Cornelius
Cornelius Remcor 620037007 Manual de usuario
Cornelius
Cornelius 2306 Manual de usuario
Cornelius
Cornelius WM600 Instrucciones de funcionamiento
Cornelius
Cornelius Flavor Fusion 22127 Manual de usuario
Cornelius
Cornelius I Series Manual de usuario
Cornelius
Cornelius Hoshizaki KM250 Manual de usuario
Cornelius
Cornelius 500-Series Manual
Cornelius
Cornelius Nordic CCU0150 Manual de usuario
Cornelius
Cornelius Nordic CCM0830 1 Guía
Cornelius
Cornelius XWC1230 Manual de usuario
Cornelius
Cornelius Series 200 Manual de usuario
Cornelius
Cornelius CCM330 Manual de usuario
Cornelius
Cornelius ED250 PRO GATE Especificaciones técnicas
