Cornelius SPIRE 4.2 Guía de seguridad

Manual Installation Conversion Kit 4.1 To 4.2

MANUAL INSTALLATION CONVERSION KIT

SPIRE 4.1 TO 4.2

SAFETY OVERVIEW

• Read and follow ALL SAFETY INSTRUCTIONS in this manual and any warning/caution labels on the unit

(decals, labels or laminated cards).

• Read and understand ALL applicable OSHA (Occupational Safety and Health Administration) safety regula-

tions before operating this unit.

SAFETY ALERT SYMBOL

Types of Alerts

SAFETY TIPS

• Carefully read and follow all safety messages in this manual and safety signs on the unit.

• Keep safety signs in good condition and replace missing or damaged items.

• Learn how to operate the unit and how to use the controls.

• Do not let anyone operate the unit without proper training. This appliance is not intended for use by very

young children or infirm persons without supervision. Young children should be supervised to ensure that

they do not play with the appliance.

• Keep your unit in proper working condition and do not allow unauthorized modifications to the unit.

Safety Instructions

WARNING:

Before starting installation, read and understand all safety label and warnings on the machine. Also review and

understand all safety instructions in the owners, installation and service manuals.

Failure to comply could result in serious injury, death or damage to the equipment.

This is the safety alert symbol. When you see this in the manual or on the unit, be alert to the

potential of personal injury or damage to the unit.

DANGER:

Indicates an immediate hazardous situation which if not avoided WILL result in serious

injury, death or equipment damage.

WARNING:

Indicates a potentially hazardous situation which, if not avoided, COULD result in serious

injury, death, or equipment damage.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or

moderate injury or equipment damage.

Revision Date: June 7, 2019 www.cornelius.com Revision: B

Manual Installation Conversion Kit 4.1 To 4.2

QUALIFIED SERVICE PERSONNEL

WARNING:

Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.

All wiring and plumbing must conform to national and local codes. Failure to comply could result in serious injury,

death or equipment damage.

SAFETY PRECAUTIONS

WARNING:

Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all

power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to

the equipment.

CAUTION:

Always be sure to keep the area around the unit clean and free of clutter. Failure to keep this area clean may result in

injury or equipment damage.

CAUTION:

Note the following: This unit is not designed for use in outdoor locations. The appliance must be placed in a horizontal

position. The appliance is not suitable for installation in an area where a water jet would be used.

Manual Installation Conversion Kit 4.1 To 4.2

MANUAL INSTALLATION CONVERSION KIT SPIRE 4.1 TO 4.2

INSTALL KIT PART LIST:

TOOLS REQUIRED:

INSTALLATION INSTRUCTION:

1. Shut Down unit per proper shutdown procedure

2. Unplug unit from its AC Power source.

PART NUMBER DESCRIPTION QTY

620070411 Ebox cover (pre-assembled with all required labels and

new wiring diagram) 1

620070273 Door service cover pre-assembled w/ mounting screws

and labels) 1

N/A AIO Display assembly (pre-assembled with bezel and

mounting bracket and screws) 1

N/A LX3 mounting bracket assembly (pre-assembled w/LX3,

terminal block, display on/ off switch and required wiring/

jumpers)

62058545-002 Breaker Circuit 5A 1

620058733-003 Ferrite Snap- On 240 Ohm 1

620058733-007 Ferrite Snap- On 225 Ohm 1

620070445 Flex Antenna Kit 2

620070523-200 MFV Board Assy 1

620070550 Bracket 3rd Circuit Breaker 1

620070556 Cable Clamp 2

629097805 Installation Instructions 1

Description

#2 Phillips Screwdriver

Utility Knife or side-cutting pliers

Flat Head Screwdriver

11/32” nut driver or equivalent

WARNING

Only trained and certified electrical, plumbing and refrigeration technicians should

service this unit.

All wiring and plumbing must conform to National and Local Codes. Failure to

comply could result in serious injury, death or equipment damage.

Manual Installation Conversion Kit 4.1 To 4.2

3. Locate power cord inside unit next to the valves and add ferrite supplied on the power cord at approximate

location shown.

Figure 1

4. Open door and remove translucent door service panel and discard of properly.

Figure 2

Manual Installation Conversion Kit 4.1 To 4.2

5. Unplug all connections to display, this includes the cove lighting to the LX3 board.

Figure 3

6. Remove ebox cover saving the (2) screws. Discard ebox cover.

7. Unplug all cables/harnesses from MFV board, remove and properly discard MFV board, install new MFV board supplied

with the kit and reinstall previously removed cables/harnesses.

8. Remove wire bundle from the (2) most far right wire clips.

Figure 4

9. From the same wire bundle, remove the (2) USB cables that feed the MFV board, USB hub and the (1) antenna cable that

goes to the rear of the unit.

10. Carefully remove/clip off the (2) far most right wire clips from step 8 and discard.

11. Insert circuit breaker into the mounting bracket supplied.

cove lighting harness

Manual Installation Conversion Kit 4.1 To 4.2

12. Insert new circuit breaker bracket into the(2) holes where the wire clips used to be. Use (2) #8-32 nuts to secure the

bracket to the unit. (DO NOT OVERTIGHTEN)

Figure 5

13. Install (2) new cable clip supplied with kit to the mounting studs of the circuits breaker with (1) #8-32 nut on each stud as

shown. (DO NOT OVERTIGHTEN)

Figure 6

Manual Installation Conversion Kit 4.1 To 4.2

14. Wire new circuit breaker with supplied harness, one end goes to the 12VDC Power supply (red to V+, black to V-)....the

other gets routed to the door with the (2) USB Cables and (1) antenna cable. Refer to new wiring diagram supplied with

kit for reference.

15. Bundle wires thru wire clips shown on step 11 except the (2) USB cables, (1) antenna cable and display/cove lighting

harnesses.

16. Using the supplied wire ties, secure the (2) USB cables, (1) antenna cable and display/cove lighting harnesses from the

main wire bundle downward approx. 1.5'' to 2''. Make sure all wires/cables are cleanly bundled and secured.

Figure 9

Figure 7 Figure 8

1.5''-2.0''

Manual Installation Conversion Kit 4.1 To 4.2

17. Remove the NUC mounting panel assembly from the door by loosen the (2) top screws and removing the (2) bottom

screws, discard bottom screws. Lift the panel assembly up and out, this panel assembly can be discarded. Remove the (2)

top screws and save.

Figure 10

18. Remove the display assembly from the door by loosening the ‘A’ screws and removing and saving the ‘B’ screws.

Figure 11

19. Carefully lift up and out the display assembly from the door. Place display assembly on a protected table top, glass side

down to get ready to remove lens/lighting.

Manual Installation Conversion Kit 4.1 To 4.2

20. Remove and save the (6) ‘C’ screws, lift up the lens / lighting and place aside and then remove the (3) white reflectors.

The old display can now be disposed of per local, state or national recycling laws for electronic equipment.

21. Reassemble the reflectors and lens / lighting into the new display assembly supplied in the kit. Do not overtighten the

screws that mount the lens / lighting, these should be hand tight only. Make sure the lighting harness is routed thru

the lens opening as shown below.

Figure 14

Figure 12 Figure 13

Manual Installation Conversion Kit 4.1 To 4.2

22. Mount new display assembly onto door key slots. Reinstall ‘B’ screws from step 18. Tighten all (8) screws hand tight only.

(DO NOT OVERTIGHTEN)

23. Clean back of door with mild detergent or alcohol wipe to prepare the surface for the adhesive tape. Remove tape backing

from new LX3 mounting bracket (backside of bracket) and install bracket using (2) screws from step 17. Firmly push

bracket, where tape is located, into door for best tape adhesion.

Figure 15

24. Install the display power harness from ebox at ‘Z’ and the cove lighting harness from the 3rd circuit breaker at ‘Y’ onto the

terminal block. Note the wire colors and their locations installed on the terminal block.

Figure 16

Tape location

underneath

bracket

screw

Clean back

of door

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Dispensador de Cornelius

Cornelius

Cornelius ED22 Series Manual de usuario

Cornelius

Cornelius Millenium II 4000 Manual de usuario

Cornelius

Cornelius Enduro 200 Manual de usuario

Cornelius

Cornelius Flavor OverLoad CG5017-1007 Manual de usuario

Cornelius

Cornelius Jetspray JT20 Manual de usuario

Cornelius

Cornelius QUEST ELITE QLT 2000 Manual

Cornelius

Cornelius UF-1 Guía de configuración

Cornelius

Cornelius FCB POST-MIX DISPENSER Suplemento

Cornelius

Cornelius 2232 Manual de usuario

Cornelius

Cornelius Remcor TJ45-D Manual de usuario

Cornelius

Cornelius ABS 2.0 Manual de usuario

Cornelius

Cornelius REMCOR 1550 Guía de configuración

Cornelius

Cornelius pbd175 Manual de usuario

Cornelius

Cornelius DF250 Manual de usuario

Cornelius

Cornelius Quest Elite 2000 Manual de usuario

Cornelius

Cornelius Universal 750 2849949xxx Guía de configuración

Cornelius

Cornelius FRUITISTA 3 Manual de usuario

Cornelius

Cornelius Ribbon Manual de usuario

Cornelius

Cornelius ICE-COOLED CHEST-A-FIELD DISPENSER Manual de usuario

Cornelius

Cornelius IDC Pro255 Manual de usuario

Cornelius

Cornelius CNB BIB Manual de usuario

Cornelius

Cornelius UltraFlow Manual de usuario

Cornelius

Cornelius IDC Pro Guía

Cornelius

Cornelius NITROPRO MINI Manual de usuario

Manuales populares de Dispensador de otras marcas

Silver King

Silver King Majestic SK12MAJ Guía de inicio rápido

Franke

Franke F3Dn Twin Manual de usuario

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manual de usuario

DAN DRYER

DAN DRYER 282 Manual de usuario

Essity

Essity Tork 473208 Manual de usuario

CBS

CBS SD300BU-88 Guía de configuración

Sealey

Sealey MK77 Manual de usuario

Fluid Management

Fluid Management Accutinter 1600 Manual de usuario

Franke

Franke DVS SD99-010 Manual de usuario

Graco

Graco Dispensit 1053-10C Guía de solución de problemas

ITALTINTO

ITALTINTO i50 Manual de usuario

Coca-Cola

Coca-Cola FREESTYLE 9000 Manual de usuario

Graco

Graco ProMix 2KE Manual de instrucciones

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manual de usuario

Wayne

Wayne GLOBAL VISTA CNG Manual de usuario

clarsen

clarsen H133 Manual de usuario

PicoBrew

PicoBrew Zymatic Manual de usuario

BOWMAN

BOWMAN BP-007 Manual de usuario