Cornelius IDC Pro Guía
IDC Pro - SSD Replacement Instructions
© 2019, Cornelius Inc. - 1 - Publication Number: 629097779INS
IDC PRO SSD REPLACEMENT INSTRUCTIONS
SAFETY OVERVIEW
• Read and follow ALL SAFETY INSTRUCTIONS in this manual and any warning/caution labels on the unit
(decals, labels or laminated cards).
• Read and understand ALL applicable OSHA (Occupational Safety and Health Administration) safety
regulations before operating this unit.
SAFETY ALERT SYMBOL
TYPES OF ALERTS
SAFETY TIPS
• Carefully read and follow all safety messages in this manual and safety signs on the unit.
• Keep safety signs in good condition and replace missing or damaged items.
• Learn how to operate the unit and how to use the controls.
• Do not let anyone operate the unit without proper training. This appliance is not intended for use by very
young children or infirm persons without supervision. Young children should be supervised to ensure that
they do not play with the appliance.
• Keep your unit in proper working condition and do not allow unauthorized modifications to the unit.
This is the safety alert symbol. When you see this in the manual or on the unit, be alert to the
potential of personal injury or damage to the unit.
!
DANGER:
Indicates an immediate hazardous situation which if not avoided WILL result in serious
injury, death or equipment damage.
!
WARNING:
Indicates a potentially hazardous situation which, if not avoided, COULD result in serious
injury, death, or equipment damage.
CAUTION:
!
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or
moderate injury or equipment damage.
!
Revision Date: August 02, 2019 www.cornelius.com Revision: A
IDC Pro - SSD Replacement Instructions
Publication Number: 629097779INS - 2 - © 2019, Cornelius Inc.
SAFETY INSTRUCTIONS
!
WARNING:
Before starting installation, read and understand all safety label and warnings on the machine. Also review and
understand all safety instructions in the owners, installation and service manuals.
Failure to comply could result in serious injury, death or damage to the equipment.
QUALIFIED SERVICE PERSONNEL
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.
All wiring and plumbing must conform to national and local codes. Failure to comply could
result in serious injury, death or equipment damage.
SAFETY PRECAUTIONS
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work. Failure to comply could result in serious injury,
death or damage to the equipment.
CAUTION:
!
Always be sure to keep the area around the unit clean and free of clutter. Failure to keep this area clean may
result in injury or equipment damage.
CAUTION:
!
Note the following: This unit is not designed for use in outdoor locations. The appliance must be placed on horizontal
surface. The appliance is not suitable for installation in an area where a water jet would be used.
IDC Pro - SSD Replacement Instructions
© 2019, Cornelius Inc. - 3 - Publication Number: 629097779INS
IMPORTANT
Before replacing SSD, if unit is operational or you have a second IDC PRO unit with an identical brand lineup be sure
to get a back up copy of the unit’s configuration onto a USB memory stick (see troubleshooting pages 13-17
“
Exporting brand configuration from a pre-existing machine
”) and or write down the units flavor line up on the provided
Flavor Line Up sheet. This will speed up the process when you are reconfiguring the unit after new SSD is put into
screen.
IDC PRO FLAVOR LINE UP
• Up to 10 brands per multi-flavor valve
• Up to 4 flavor shots per multi-flavor valve
• One plain water per valve, with optional flavor shots
• One carbonated water per valve
• One flavor shot pour per valve
Dispenser serial number - _______________________________
Left Side Right Side
S1 ______________________________ S8 ___________________________
S2 ______________________________ S9 ___________________________
S3 ______________________________ S10 ___________________________
S4 ______________________________ S11 ___________________________
S5 ______________________________ S12 ___________________________
S6 ______________________________ S13 ___________________________
S7 ______________________________ S14 ___________________________
A1 ______________________________ A4 ___________________________
A2 ______________________________ A5 ___________________________
A3 ______________________________ A6 ___________________________
Flavor Shots
F1 ______________________________ F5 ___________________________
F2 ______________________________ F6 ___________________________
F3 ______________________________ F7 ___________________________
F4 ______________________________ F8 ___________________________
• S1-S14 will run through the cold plate and will be used for your carbonated brands.
• A1-A6 is your ambient lines and will be used for your non-carbonated brands. If you have more than 7
carbonated brands you can run carbonated brands through the ambient lines but you want to use a low
volume and low foaming brand.
IDC Pro - SSD Replacement Instructions
Publication Number: 629097779INS - 4 - © 2019, Cornelius Inc.
TOOLS REQUIRED:
1. Large Phillips Screw Driver
2. Fine Tip Phillips Screw Driver
NOTE: Wear a properly grounded ESD wrist strap if available & minimize body contact with electronic components.
SSD REPLACEMENT INSTRUCTION
Table 1:
Step Action Figure
1
A. Disconnect power to the unit.
B. Locate the SBC Cover on the back side of
the door.
C. Remove the 4 screws as shown.
D. Carefully hold the cover until the Fan
harness is disconnected.
Figure 1.
2Disconnect the Fan harness and remove the
Cover.
Figure 2.
IDC Pro - SSD Replacement Instructions
© 2019, Cornelius Inc. - 5 - Publication Number: 629097779INS
3Carefully undo the lock screw to unlock the SSD.
NOTE: DO NOT LOOSE THIS PART!
Figure 3.
4Carefully replace the SSD with a new part.
Figure 4.
5
Carefully secure the lock screw to lock the SSD.
NOTE: DO NOT LOOSE THIS PART!
Figure 5.
Table 1: (Continued)
IDC Pro - SSD Replacement Instructions
Publication Number: 629097779INS - 6 - © 2019, Cornelius Inc.
6
Connect the Fan harness and replace the Cover.
Make sure the silicone (white glue) doesn’t get in
the way of the pins and connector.
Figure 6.
7
A. Close the SBC cover
B. Secure the 4 screws as shown
C. Reconnect the Power harness
D. After Power up, ensure the Fan is working
properly.
Figure 7.
Table 1: (Continued)
IDC Pro - SSD Replacement Instructions
© 2019, Cornelius Inc. - 7 - Publication Number: 629097779INS
TROUBLESHOOTING
SCREEN RESOLUTION COMES UPINCORRECT
Table 2:
Step Action Figure
1
If image on the screen appears to be too far
zoomed in or out, the screen resolution will
need to be adjusted in the BIOS settings.
Figure 8.
2
Plug in a keyboard into a USB port on the
back of the screen. Restart the unit and
during the initial startup “AAEON” screen,
continually press the DELETE key.
Figure 9.
3
BIOS menu will display as shown in the
picture. Using the keyboard arrow keys move
over to the “Chipset” tab.
Figure 10.
IDC Pro - SSD Replacement Instructions
Publication Number: 629097779INS - 8 - © 2019, Cornelius Inc.
4“North Bridge” should already be highlighted,
press the ENTER key.
Figure 11.
5Use the down arrow key to highlight “LVDS
Panel Type” and press ENTER key.
Figure 12.
6
From the dropdown list select the “1920 x
1080, 48 bit, 60hz” option and press the
ENTER key.
Figure 13.
Table 2: (Continued)
IDC Pro - SSD Replacement Instructions
© 2019, Cornelius Inc. - 9 - Publication Number: 629097779INS
7LVDS Panel type will now read “1920 x 1080,
48 bit, 60hz”.
Figure 14.
8Press F4 on the keyboard to Save and Exit.
9
On the “Save & Exit Setup” screen, highlight
“Yes” and Press ENTER key. Unit will restart
and the screen resolution should come up
normal.
Figure 15.
Table 2: (Continued)
IDC Pro - SSD Replacement Instructions
Publication Number: 629097779INS - 10 - © 2019, Cornelius Inc.
TROUBLESHOOTING
MAPPING BRANDS
Table 3:
Step Action Figure
1
Display the keypad screen by tapping
each corner of the video screen start-
ing in the upper right corner and con-
tinuing to tap each corner in a
counterclockwise direction, in the
form of a “C”.
NOTE: As each corner is touched, a
small confirmation rectangle
momentarily appears to con-
firm the touch.
Figure 16.
2
Input the proper password for your
access level (technician) and press
“Enter”.
Password is 3333
Figure 17.
Otros manuales para IDC Pro
4
Tabla de contenidos
Otros manuales de Dispensador de Cornelius
Cornelius
Cornelius essense Manual de usuario
Cornelius
Cornelius QUEST CAFE Guía de configuración
Cornelius
Cornelius QUEST ELITE QLT 2000 Manual
Cornelius
Cornelius UltraFlow Manual de usuario
Cornelius
Cornelius Quest Elite 2000 Manual de usuario
Cornelius
Cornelius FCB 3 H.P. POST-MIX DISPENSER Suplemento
Cornelius
Cornelius ICE-COOLED CHEST-A-FIELD DISPENSER Manual de usuario
Cornelius
Cornelius Vitalize430 Manual del operador
Cornelius
Cornelius VANTAGE Manual de usuario
Cornelius
Cornelius NITROPRO MINI Manual de usuario
Cornelius
Cornelius Remcor TJ45-D Manual de usuario
Cornelius
Cornelius QUEST 4000 Manual de usuario
Cornelius
Cornelius REMCOR 1550 Guía de configuración
Cornelius
Cornelius QUEST ELITE 4290 Manual de usuario
Cornelius
Cornelius CNB BIB Manual de usuario
Cornelius
Cornelius VIPER Manual de usuario
Cornelius
Cornelius 318569000 Manual de usuario
Cornelius
Cornelius FCB OVERCOUNTER POST-MIX DISPENSER Manual de usuario
Cornelius
Cornelius ED 300 BC Manual de usuario
Cornelius
Cornelius ED2XX-B Series Manual de usuario
